Combination Meter: Installation

WARNING: This page is about a different car, the 2008 Lexus LS 600hL. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL COMBINATION METER ASSEMBLY
1. Connect the connector.
  
  Fig 1: Installing Combination Meter Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the combination meter with the 4 screws.
  
  Fig 2: Locating Combination Meter Screws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
1. Rotate the finish panel as shown in the illustration to install it.
  
  Fig 3: Rotating Finish Panel For Installation
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Hold the back of the trip switch on the finish panel with your right hand, and connect the connector with your left hand.
  
  Fig 4: Locating Instrument Cluster Finish Panel Trip Switch Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Hold the back of the light control rheostat on the finish panel with your right hand, and connect the connector with your left hand.
  
  Fig 5: Locating Instrument Cluster Finish Panel Light Control Rheostat Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Insert the upper part of the finish panel into the instrument panel opening, and fix the center with your right hand.
  
  Fig 6: Locating Instrument Cluster Finish Panel Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Press up the lower right side of the finish panel to attach the clip.
  NOTE: If the trip switch is pressed to attach the clip, the switch will be damaged.
  
  Fig 7: Identifying Finish Panel Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Press up the lower left side of the finish panel to attach the clip
  NOTE: If the light control rheostat switch is pressed to attach the clip, the switch will be damaged.
  
  Fig 8: Identifying Finish Panel Clip
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Install the 2 clips
INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY (See INSTALLATION )
INSTALL STEERING COLUMN COVER (w/o Driver Monitor Camera) (See INSTALLATION )
INSTALL STEERING COLUMN COVER (w/ Driver Monitor Camera) (See INSTALLATION )

Fig 9: Identifying Instrument Cluster Finish Panel Clips
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
1. Connect the connectors.
2. Attach the 5 clips and claw to install the safety pad
3. Install the 2 screws
  
  Fig 10: Identifying No. 1 Instrument Panel Safety Pad Clips And Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Attach the claw to install the hole cover
Fig 11: Identifying Panel Safety Pad Claw
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 1 INSTRUMENT CLUSTER MOLDING
1. Attach the 2 clips to install the molding
Fig 12: Identifying No. 1 Instrument Cluster Molding Clips
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INSTRUMENT SIDE PANEL LH
1. Attach the 6 clips to install the side panel.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE:
- Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter (see CUSTOMIZE PARAMETERS ).
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (see INITIALIZATION ).
Fig 13: Identifying Instrument Side Panel LH Clips
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL BATTERY SERVICE HOLE COVER LH (See INSTALLATION )
INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (See INSTALLATION )