Combination Meter: Installation: Installation

INSTALL COMBINATION METER ASSEMBLY
1. Connect the connector.
  
  Fig 1: Installing Combination Meter Assembly Harness Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the combination meter with the 4 screws.
  
  Fig 2: Identifying Combination Meter Assembly Screw Fasteners
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
1. Rotate the finish panel as shown in the illustration to install it.
  
  Fig 3: Rotating Finish Panel For Installation
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Hold the back of the trip switch on the finish panel with your right hand, and connect the connector with your left hand.
  
  Fig 4: Locating Instrument Cluster Finish Panel Trip Switch Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Hold the back of the light control rheostat on the finish panel with your right hand, and connect the connector with your left hand.
  
  Fig 5: Locating Instrument Cluster Finish Panel Light Control Rheostat Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Insert the upper part of the finish panel into the instrument panel opening, and fix the center with your right hand.
  
  Fig 6: Locating Instrument Cluster Finish Panel Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Press up the lower right side of the finish panel to attach the clip.
  
  Fig 7: Identifying Finish Panel Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  NOTE:
  If the trip switch is pressed to attach the clip, the switch will be damaged.
6. Press up the lower left side of the finish panel to attach the clip.
  
  Fig 8: Identifying Finish Panel Clip
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  NOTE:
  If the light control rheostat switch is pressed to attach the clip, the switch will be damaged.
7. Install the 2 clips.
  
  Fig 9: Identifying Instrument Cluster Finish Panel Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY . Refer to INSTALLATION - Step 1
INSTALL STEERING COLUMN COVER (w/o Driver Monitor Camera) . Refer to INSTALLATION - Step 2
INSTALL STEERING COLUMN COVER (w/ Driver Monitor Camera) . Refer to INSTALLATION - Step 3
INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
1. Connect the connectors.
  
  Fig 10: Identifying No. 1 Instrument Panel Safety Pad Claw, Clips And Screws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Attach the 5 clips and claw to install the safety pad.
3. Install the 2 screws.
4. Attach the claw to install the hole cover.
  
  Fig 11: Identifying Panel Safety Pad Claw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 1 INSTRUMENT CLUSTER MOLDING
1. Attach the 2 clips to install the molding.
  
  Fig 12: Identifying No. 1 Instrument Cluster Molding Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INSTRUMENT SIDE PANEL LH
1. Attach the 6 clips to install the side panel.
  
  Fig 13: Identifying Instrument Side Panel LH Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE:
- Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter. Refer to CUSTOMIZE PARAMETERS .
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Refer to INITIALIZATION .
INSTALL BATTERY SERVICE HOLE COVER LH . Refer to INSTALLATION - Step 15
INSTALL DECK TRIM SIDE BOARD LH . Refer to INSTALLATION - Step 16
INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY . Refer to INSTALLATION - Step 17
INITIALIZE COMBINATION METER
HINT:

If the combination meter assembly has been replaced with a new one, it is necessary to perform initialization. Refer to INITIALIZATION .