Shift Lever Position Sensor: Installation: Installation

INSTALL PARK/NEUTRAL POSITION SWITCH
1. Install the park/neutral position switch to the hybrid vehicle transmission assembly.
2. Temporarily install the 2 bolts.
  
  Fig 1: Locating Park/Neutral Position Switch Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  Fully tighten the bolts with the neutral alignment mark line aligned with the groove. [*1]
3. Install a new lock washer and the nut.
  
  Fig 2: Locating Lock Washer And Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 6.9 N*m (70 kgf*cm, 61 in.*lbf)
4. Temporarily install the control shaft lever with the nut.
  
  Fig 3: Locating Washer And Transmission Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  Bend the tabs of the lock washer before fully tightening the nut. [*2]
5. Turn the control shaft lever counterclockwise until it stops. Next, turn the control shaft lever clockwise 2 notches to set it to the N position.
  
  Fig 4: Turning Control Shaft Lever Counterclockwise
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Remove the nut and transmission control shaft lever.
  
  Fig 5: Locating Washer And Transmission Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Align the neutral alignment mark line with the switch groove, and tighten the 2 adjusting bolts. [*1]
  
  Fig 6: Locating Shift Lever Position Sensor Bolts With Neutral Alignment Mark And Groove
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
8. Using a screwdriver, bend the tabs of the lock washer.
  
  Fig 7: Bending Tabs Of Lock Washer
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  NOTE:
  Make sure that the nut is held firmly.
9. Install the transmission control shaft lever with the nut. [*2]
  
  Fig 8: Locating Washer And Transmission Control Shaft Lever Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 16 N*m (163 kgf*cm, 12 ft.*lbf)
10. Connect the park/neutral position switch connector.
  
  Fig 9: Locating Park/Neutral Position Switch Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY
1. Move the shift lever to the N position and tighten the nut while lightly pushing the lever toward the R position.
  
  Fig 10: Locating Floor Shift Gear Shifting Rod Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 13 N*m (130 kgf*cm, 9 ft.*lbf)
  
  NOTE:
  Do not push the shift lever too hard.
INSTALL OIL COOLER TUBE
1. Install the oil cooler tube with the 3 bolts in the order shown in the illustration.
  
  Fig 11: Locating Oil Cooler Tube Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf)
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Refer to INITIALIZATION .
INSPECT SHIFT LEVER POSITION See step 1
INSPECT PARK/NEUTRAL POSITION SWITCH POSITION See step 3
ADJUST PARK/NEUTRAL POSITION SWITCH POSITION See step 4
INSPECT SHIFT LEVER OPERATION See step 2
INSTALL NO. 2 ENGINE UNDER COVER . Refer to INSTALLATION - Step 86
INSTALL FRONT FLOOR COVER CENTER . Refer to INSTALLATION - Step 87
INSTALL BATTERY SERVICE HOLE COVER LH . Refer to INSTALLATION - Step 15
INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)
INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire) . Refer to INSTALLATION - Step 16
INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY . Refer to INSTALLATION - Step 17