Adjustment [10/2016 - 09/2020]: Procedure

Refer to PROCEDURE - Step 1

See step  2

1. Install a camber-caster-kingpin gauge.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Camber-caster-kingpin Gauge

2. Inspect the camber.

   Camber (Unloaded Vehicle)

   -	Camber Inclination	Right-left Difference
   2WD	-1°35' +/- 0°45' (-1.58° +/- 0.75°)	0°45' (0.75°) or less
   AWD	-1°38' +/- 0°45' (-1.63° +/- 0.75°)

   HINT: 

   Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.

1. Bounce the vehicle up and down at the corners to stabilize the suspension.
2. Release the parking brake and move the shift lever to N.
3. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
4. Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Tread Center Mark
   *b	Dimension B
   	Front of the Vehicle

5. Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

   HINT: 

   Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.

6. Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *a	Dimension A
   	Front of the Vehicle

   Toe-in (Unloaded Vehicle)

   Specified Condition
   C + D: 0°11' +/- 0°11' (0.18° +/- 0.18°)
   B - A: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.)

   HINT: 

   Measure "B - A" only when "C + D" cannot be measured.

   If the toe-in is not within the specified range, adjust it at the toe control link sub-assembly.

1. Loosen the nut of the toe control link sub-assembly (on the rear suspension member sub-assembly side).
   NOTE:

   Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Rotate the rear suspension toe adjust cam sub-assembly to adjust the toe-in.

   Toe-in (Unloaded Vehicle)

   Specified Condition
   C + D: 0°11' +/- 0°11' (0.18° +/- 0.18°)
   B - A: 2.0 +/- 2.0 mm (0.0787 +/- 0.0787 in.)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT: 

   • Perform adjustments so that the value is as close as possible to the median of the specified range.
   • Rotating the toe adjust cam sub-assembly by one notch changes the toe by approximately 4.7 mm (0.185 in.).
3. Tighten the nut of the toe control link sub-assembly (on the rear suspension member sub-assembly side).

   Torque: 117 N.m (1193 kgf/cm, 86 ft.lbf) 

   NOTE:

   Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.

1. Inspect the rear suspension member sub-assembly.
   1. Measure the distance between the centers of the 2 installation bolts of the rear No. 2 suspension arm assembly LH and RH.

      Standard

      496.5 to 503.5 mm (1.63 to 1.65 ft.)

      If the distance is not within the specified range, replace the rear suspension member sub-assembly.

      HINT: 

      Refer to the instructions for Removal and Installation of the rear suspension member sub-assembly.

      Refer to REMOVAL [10/2016 - 10/2017] , or refer to REMOVAL [10/2017 - 09/2020]

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

2. Inspect the rear No. 2 suspension arm assembly.
   1. Measure the distance between the centers of the 2 installation bolts of the rear No. 2 suspension arm assembly.

      Standard

      433.2 to 435.0 mm (1.421 to 1.426 ft.)

      If the distance is not within the specified range, replace the rear No. 2 suspension arm assembly.

      HINT: 

      Refer to the instructions for Removal and Installation of the rear No. 2 suspension arm assembly.

      Refer to REMOVAL [06/2014 - 09/2020]

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

3. Inspect the rear upper control arm assembly.
   1. Measure the distance between the centers of the 2 installation bolts of the rear upper control arm assembly.

      Standard

      298.5 to 299.5 mm (11.76 to 11.79 in.)

      If the distance is not within the specified range, replace the rear upper control arm assembly.

      HINT: 

      Refer to the instructions for Removal and Installation of the rear upper control arm assembly.

      Refer to REMOVAL [04/2013 - ]

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Refer to CALIBRATION [10/2016 - 09/2020]