Common Specs & Procedures
IS 200t COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA [04/2013 - 09/2020] | ||
| Torque | TORQUE SPECIFICATIONS [08/2015 - 09/2020] | ||
| Axle Nut/Hub Nut | |||
| Front | NA | ||
| Rear | 290 N.m (2, 957 kgf.cm 214 ft.lbf) | ||
| Battery | SERVICE DATA [08/2015 - 09/2020] | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING [04/2013 - 10/2016] or BLEEDING [10/2016 - 09/2020] | ||
| Front Brakes | SERVICE DATA [08/2015 - 09/2020] | ||
| Torque | TORQUE SPECIFICATIONS [08/2015 - 09/2020] | ||
| Rear Brakes | SERVICE DATA [08/2015 - 09/2020] | ||
| Torque | TORQUE SPECIFICATIONS [04/2013 - 09/2020] | ||
| Charging | |||
| Generator | SERVICE DATA [08/2015 - 09/2020] | ||
| Torque | TORQUE SPECIFICATIONS [08/2015 - 09/2020] | ||
| Drive Belts | |||
| Adjustment | ON-VEHICLE INSPECTION [08/2015 - ] | ||
| Belt Routing | INSTALLATION [08/2015 - ] | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE DATA [08/2015 - ] | ||
| Radiator Cap Pressure | Standard valve (for brand-new cap) 93 to 123 kPa (0.9 to 1.3 kgf/cm2 , 13.5 to 18.0 psi) Minimum standard valve (for used cap) 79 kPa (0.8 kgf/cm2 , 11.5 psi) |
||
| Thermostat R & I | THERMOSTAT , and THERMOSTAT (FOR CYLINDER BLOCK) | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | ON-VEHICLE INSPECTION [08/2015 - 09/2020], Step 10 | ||
| Oil Pressure | At Idle: 30 kPa (0.3 kgf.cm2 , 4.4 psi) or higher At 2500 RPM: 260 kPa (2.7 kgf.cm2 , 38 psi) or higher |
||
| Overhaul | SERVICE DATA [08/2015 - 09/2020] | ||
| Torque | TORQUE SPECIFICATIONS [08/2015 - 10/2016] or TORQUE SPECIFICATIONS [10/2016 - 09/2020] | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | 98 N.m (999 kgf.cm, 72 ft.lbf) | ||
| Fuel System | |||
| Standard Fuel Pressure | 196 to 833 kPa (2.0 to 8.5 kgf/cm2 , 28 to 121 psi) | ||
| Standard Fuel Pressure (For High Pressure) | 4000 to 8000 kPa (40.8 to 81.6 kgf/cm2 , 580 to 1160 psi) | ||
| Fuel Pressure Test Procedure | ON-VEHICLE INSPECTION [08/2015 - ] | ||
| Fuel Filter Location | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Spark Plug | |||
| Type | NGK DILFR7K9G | ||
| Gap | Standard electrode gap for new spark plug: 0.8 - 0.9 mm (0.0315 - 0.0354 in.) Maximum electrode gap for used spark plug: 1.1 mm (0.0433 in.) |
||
| Torque | 25 N.m (255 kgf.cm, 18 ft.lbs) | ||
| Starting | |||
| Starter | SERVICE DATA [08/2015 - ] | ||
| Torque | TORQUE SPECIFICATIONS [08/2015 - ] | ||
| Wheel Alignment | |||
| Adjustment Specifications | SERVICE DATA [08/2015 - 10/2016] or SERVICE DATA [10/2016 - 09/2020] | ||
| Torque | TORQUE SPECIFICATIONS [04/2013 - ] | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 N.m (1, 050 kgf.cm 76 ft.lbf) | ||