Common Specifications & Procedures
NAUTILUS COMMON SPECIFICATIONS & PROCEDURES
| System | Specifications/Procedures | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATIONS | ||
| Torque | Refer to the appropriate procedure in REMOVAL AND INSTALLATION | ||
| Axle Nut/Hub Nut | |||
| 203 Ft. Lbs. (275 N.m) | |||
| Battery | SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | BRAKE SYSTEM PRESSURE BLEEDING |
||
| Front Disc Brakes w/Torque | Refer to the appropriate component in REMOVAL AND INSTALLATION | ||
| Rear Disc Brakes w/Torque | Refer to the appropriate component in REMOVAL AND INSTALLATION | ||
| Charging | |||
| Generator w/Torque | |||
| 2.0L | Lower Generator Bolts: 35 lb.ft (47.5 Nm) Upper Generator Bolt: 35 lb.ft (47.5 Nm) |
||
| Drive Belts | |||
| 2.0L EcoBoost - Hybrid (FHEV 224kW 300PS) (S0) | |||
| Adjustment | ACCESSORY DRIVE BELT | ||
| Belt Routing | Accessory Drive - Component Location | ||
| 2.0L EcoBoost (184kW 250PS) (E3) | |||
| Adjustment | Accessory Drive Belt | ||
| Belt Routing | Accessory Drive - Component Location | ||
| Engine Cooling | |||
| 2. 0L EcoBoost - Hybrid (FHEV 224kW 300PS) (S0) | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | 145 kPa (21 psi) | ||
| Thermostat R & I | Thermostat | ||
| Water Pump R & I | Coolant Pump | ||
| 2.0L EcoBoost (184kW/250PS) (E3) | |||
| General Service Specifications | SPECIFICATIONS | ||
| Radiator Cap Pressure | 145 kPa (21 psi) | ||
| Thermostat R & I | Thermostat | ||
| Water Pump R & I | Coolant Pump | ||
| Engine Mechanical | |||
| 2.0L EcoBoost - Hybrid (FHEV 224kW/300PS) (S0) | |||
| Compression | SPECIFICATIONS | ||
| Oil pressure @ 1, 500 rpm with engine oil temperature between 50-80°C | 190-300 kPa | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | Refer to the appropriate procedure in REMOVAL AND INSTALLATION | ||
| 2.0L EcoBoost (184kW/250PS) (E3) | |||
| Compression | SPECIFICATIONS | ||
| Oil pressure @ 1, 500 rpm with engine oil temperature between 50-80°C | 190-300 kPa | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | Refer to the appropriate procedure in REMOVAL AND INSTALLATION | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| 2.0L EcoBoost - Hybrid (FHEV 224kW/300PS) (S0) | For tightening sequence, refer to Flexplate |
||
| 2.0L | For tightening sequence, refer to Stage 1: 37 lb.ft (50 Nm) Stage 2: 59 lb.ft (80 Nm) Stage 3: 83 lb.ft (112 Nm) |
||
| Fuel System | |||
| 2. 0L EcoBoost - Hybrid (FHEV 224kW 300PS) (S0) | |||
| Fuel Filter Location | Located in fuel tank as part of Fuel Pump Module. | ||
| Fuel Filter R & I | Fuel Pump and Sender Unit | ||
| Pressure Release Procedure | Fuel System Pressure Release | ||
| Pressure Specification | SPECIFICATIONS | ||
| Fuel Pressure Test Procedure | Fuel System Pressure Check | ||
| 2.0L EcoBoost (184kW 250PS) (E3) | |||
| Fuel Filter Location | Located in fuel tank as part of Fuel Pump Module. | ||
| Fuel Filter R & I | Fuel Pump and Sender Unit | ||
| Pressure Release Procedure | Fuel System Pressure Release | ||
| Pressure Specification | SPECIFICATIONS | ||
| Fuel Pressure Test Procedure | Fuel System Pressure Check | ||
| Ignition | |||
| 2.0L EcoBoost - Hybrid (FHEV 224kW 300PS) (S0) | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Routing) | Engines are equipped with Coil-on-plug ignition. | ||
| 2.0L | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Routing) | Engines are equipped with Coil-on-plug ignition. | ||
| Spark Plugs | |||
| 2.7L | |||
| Type | CYFS 12Y RT3 | ||
| Gap | 0.028-0.031 in (.7-.8 mm) | ||
| Torque | 128 lb.in (14.5 Nm) | ||
| 2.0L | |||
| Type | JYSP-12Y-PTX | ||
| Gap | 0.030 in (.75 mm) | ||
| Torque | 177 lb.in (20 Nm) | ||
| Starting | |||
| 2.0L | |||
| Starter | SPECIFICATIONS | ||
| Torque | Starter Motor Stud Bolt: 35 lb.ft (47.5 Nm) | ||
| 2.0L | |||
| Starter | STARTING SYSTEM - 2.0L ECOBOOST (184KW 250PS) (E3) | ||
| Wheel Alignment | |||
| Adjustment Specifications | SPECIFICATIONS | ||
| Torque | Refer to the appropriate procedure in GENERAL PROCEDURES . | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | For tightening sequence, refer to WHEELS AND TIRES
. 150 lb.ft (204 Nm) |
||