Technical Service Bulletins

• A/C Compressor
  • Use Of A/C Tracer Dye Service Info (CAT. U, NO. 008/97)
  • Use Of R-12 Refrigerant Substitutes (CAT. U, NO. 009/96)
  • HFC-134A A/C Recovery & Recycling Training/Equipment (CAT. ST, NO. 008/95)
  • Correct FREON Charge Warning Specs (CAT. 16, NO. 034/88)
  • 1.3L Eng Heat & A/C Fail - System Diagnosis (CAT. 15, NO. 056/88)
• Accessories & Equipment
  • All Models - WDS Ms-Can 5-Meter Cable (ST-003/04)
  • All Models - WDS Ms-Can 16-Pin Cable Shipment (ST001/03)
• Accessories Control Systems
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • Shipment Of NGS Program Card Version 2.0:Information (CAT. ST, NO. 002/94)
  • Acceptable Battery Drain (CAT. 5, NO. 017/88)
• Air Bag, SRS
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
• Anti-Lock Brakes
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • Shipment Of NGS Program Card Version 2.0:Information (CAT. ST, NO. 002/94)
• Anti-Theft Systems
  • Wind Noise Around Doors (S018/98)
  • Key Cylinder Replacement - REKEY Cylinders To Match (MT 0995-10)
  • Static ELECTRICTY Buildup - Solutions (MT 1095-11)
  • Door Trim Recess Broken -Recess Available Separately (MT 0395-03)
  • Key Replacement (CALIFORNIA Dealers Only) (CAT. AD, NO. 005/94)
  • Static Electricity Shock When Exiting Vehicle (CAT. 14, NO. 067/89)
  • Acceptable Battery Drain (CAT. 5, NO. 017/88)
• Automatic Trans
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • A/T Oil Cooler Flushing Equipment Guideline (CAT. J, NO. 96-01)
  • Recommended A/T Cooler Line Flushing Equipment (CAT. ST, NO. 009/95)
  • Automatic Transmission Repair Policy (CAT. K, NO. 002/95)
  • Automatic Transmission Diagnostic Procedures (CAT. K, NO. 002/94)
  • L4N71B Trans Revised Rear Clutch Plate Parts Info (CAT. 7, NO. 061/89)
  • Auto Transaxle Oil Leak - Change Rod Boot Breather (CAT. 7, NO. 056/89)
  • 2.2/2.6L Eng Trans Hanger Tool Modification (CAT. 40, NO. 017/87)
• Auxiliary Emission Control Systems
  • TAS (Throttle Adjustment Screw) Location/Adjustment (F014/98)
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • Shipment Of NGS Program Card Version 2.0:Information (CAT. ST, NO. 002/94)
  • Emission Inspection & Maintenance Test Preparations (CAT. F, NO. 005/93)
  • Remanufactured EGI Control Unit Program (CAT. F, NO. 010/91)
  • 1.3L Eng Hesitation At 6000 Rpm - New Air Flow Meter (CAT. 4, NO. 073/89)
  • 1.3L Eng EGI Control Unit Interchange Caution (CAT. 4, NO. 049/88)
  • 1.3L Eng Rough Idle - Damaged Water Temp Switch (CAT. 4, NO. 047/88)
  • 1.3L Eng Rough Idle Cold - Air Leak/Air Control VLV (CAT. 4, NO. 039/88)
  • Fuel Injector Color Code Table (CAT. 4, NO. 033/87)
• Axle Shafts
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Propeller Shaft/Flange Mating Mark (CAT. 8, NO. 003/88)
• Blowers, Superchargers & Turbochargers
  • 1.3L Eng Turbo Flange Cracks (CAT. 4, NO. 052/88)
• Body Interior
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • Shipment Of NGS Program Card Version 2.0:Information (CAT. ST, NO. 002/94)
  • 1.3/1.6/2.2/2.6L Eng - Ac Installation Changes (CAT. 16, NO. 029/88)
  • Warm Air At Vents W/A/C On - Heater Control LOGICON (CAT. 15, NO. 059/88)
  • 1.3L Eng Heat & A/C Fail - System Diagnosis (CAT. 15, NO. 056/88)
• Brakes Control Systems
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • Shipment Of NGS Program Card Version 2.0:Information (CAT. ST, NO. 002/94)
• Charging Systems
  • Battery Recharging - Disconnect Negative Terminal (MT 08-10)
  • Ecu/Air Flow Meter/Fuel Pump/Alternator Diagnostics (CAT. G, NO. 93-03)
• Clutch
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
• Communication Devices
  • Installation Of Tire Chains (CAT. Q, NO. 005/93)
• Cooling System (Mechanical)
  • Oil Leak At Rear Stationary Gear O-Ring - Car Fix (B003/98)
  • Intake Manifold Gasket Precautions (CAT. F, NO. 005/95)
  • Intake Manifold Gasket Precautions (CANADIAN) (CAT. F, NO. 95-03)
  • Propylene Glycol Based Coolant: Recommendations (CAT. E, NO. 001/94)
  • Workshop Manual Correction - Fuel System Inspection (CAT. W, NO. 028/92)
  • 1.3L Eng Oil Leak - New Rear Engine Oil Seal/PROC (CAT. B, NO. 007/91)
  • Oil Leak - Rear Crankshaft Oil Seal Precaution (CAT. D, NO. 002/90)
  • Reconditioned Antifreeze Warnings (CAT. E, NO. 001/90)
• Cruise Control Systems
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • Shipment Of NGS Program Card Version 2.0:Information (CAT. ST, NO. 002/94)
• Differentials & Drive Axles
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Propeller Shaft/Flange Mating Mark (CAT. 8, NO. 003/88)
• Driveshaft & Universal Joints
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Propeller Shaft/Flange Mating Mark (CAT. 8, NO. 003/88)
• Electronic Steering
  • Alignment Specifications And Tolerances -Information (CAT. N, NO. 004/94)
  • Alignment Specifications (CANADIAN) (CAT. N, NO. 95-02)
• Electronic Suspension
  • Alignment Specifications And Tolerances -Information (CAT. N, NO. 004/94)
  • Alignment Specifications (CANADIAN) (CAT. N, NO. 95-02)
  • 1988 Front/Rear Wheel Alignment Specifications (CAT. 30, NO. 004/88)
• Engine Control Systems
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • Shipment Of NGS Program Card Version 2.0:Information (CAT. ST, NO. 002/94)
  • Ecu/Air Flow Meter/Fuel Pump/Alternator Diagnostics (CAT. G, NO. 93-03)
  • Remanufactured EGI Control Unit Program (CAT. F, NO. 010/91)
  • 1.3L Eng Hesitation At 6000 Rpm - New Air Flow Meter (CAT. 4, NO. 073/89)
  • 1.3L Eng EGI Control Unit Interchange Caution (CAT. 4, NO. 049/88)
  • 1.3L Eng Rough Idle - Damaged Water Temp Switch (CAT. 4, NO. 047/88)
  • Fuel Injector Color Code Table (CAT. 4, NO. 033/87)
• Entertainment Systems
  • Power Antenna Mast - Repair Procedure (MT 0195-08)
  • Audio Storage Tray Lid Stays Open: Replacement (CAT. 15, NO. 089/89)
  • Inoperative Power Antenna: Inspection & Replacement (CAT. 15, NO. 088/89)
  • Audio System Troubleshooting Procedures (CAT. 15, NO. 078/89)
• Exhaust
  • Intake Manifold Gasket Precautions (CAT. F, NO. 005/95)
  • Rattle From Floor When ACCEL - Broken Muffler Hanger (CAT. 4, NO. 055/89)
  • 1.3L Eng Rattle - New No. 2 Pre-CONVERTOR Bracket (CAT. 4, NO. 048/88)
• Exterior Body Panels
  • Static ELECTRICTY Buildup - Solutions (MT 1095-11)
  • Painting Rustproof Steel Panels (CAT. 14, NO. 070/89)
  • Static Electricity Shock When Exiting Vehicle (CAT. 14, NO. 067/89)
• Exterior Lights
  • Room Lamp Does Not Illuminate - New Dome Light Bulb (CAT. T, NO. 016/97)
  • Acceptable Battery Drain (CAT. 5, NO. 017/88)
• Frames, Subframes & Crossmembers
  • Replacement Bumpers - Grease Removal Precautions (MT 08-03)
  • Static ELECTRICTY Buildup - Solutions (MT 1095-11)
  • Painting Rustproof Steel Panels (CAT. 14, NO. 070/89)
  • Static Electricity Shock When Exiting Vehicle (CAT. 14, NO. 067/89)
• Front Suspension
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Alignment Specifications And Tolerances -Information (CAT. N, NO. 004/94)
  • Alignment Specifications (CANADIAN) (CAT. N, NO. 95-02)
  • Squeak In Front When Cold - New Front Strut Mount (CAT. R, NO. 004/90)
  • 1988 Front/Rear Wheel Alignment Specifications (CAT. 30, NO. 004/88)
  • Recommended Coil Spring Compressors (CAT. 40, NO. 019/87)
• Fuel System
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Intake Manifold Gasket Precautions (CAT. F, NO. 005/95)
  • Ecu/Air Flow Meter/Fuel Pump/Alternator Diagnostics (CAT. G, NO. 93-03)
  • Fuel Injector Cleaner (CAT. F, NO. 001/93)
  • Recommended Fuel (CAT. 4, NO. 054/89)
  • 1.3L Eng Injector Air Bleed Socket Differences (CAT. 4, NO. 046/88)
• Fuses & Circuit Breakers
  • Front Wiper Motor Operation/Inspection (CAT. T, NO. 013/97)
  • Front Wiper Motor Inoperative (MT 0394-15)
  • Fusible Link Reference Chart (NO. T-2-3)
  • Acceptable Battery Drain (CAT. 5, NO. 017/88)
• Gauges & Instrument Panels
  • Acceptable Battery Drain (CAT. 5, NO. 017/88)
• Headlights
  • Room Lamp Does Not Illuminate - New Dome Light Bulb (CAT. T, NO. 016/97)
  • Acceptable Battery Drain (CAT. 5, NO. 017/88)
• HVAC Control Systems
  • Use Of A/C Tracer Dye Service Info (CAT. U, NO. 008/97)
  • Use Of R-12 Refrigerant Substitutes (CAT. U, NO. 009/96)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • HFC-134A A/C Recovery & Recycling Training/Equipment (CAT. ST, NO. 008/95)
  • Receiver Drier Replacement Criteria (CANADIAN) (CAT. U, NO. 95-02)
  • Receiver Drier Replacement Criteria - Information (CAT. U, NO. 001/95)
  • Heating System Troubleshooting (CAT. U, NO. 93-04)
  • A/C Pressure Relief Valve Information (CAT. U, NO. 007/90)
  • Correct FREON Charge Warning Specs (CAT. 16, NO. 034/88)
  • Poor Cooling - Diagnosing/Repair A/C Leaks (CAT. 16, NO. 033/88)
  • Warm Air At Vents W/A/C On - Heater Control LOGICON (CAT. 15, NO. 059/88)
  • 1.3L Eng Heat & A/C Fail - System Diagnosis (CAT. 15, NO. 056/88)
• Ignition Switch/Steering Lock
  • Key Replacement (CALIFORNIA Dealers Only) (CAT. AD, NO. 005/94)
• Ignition System
  • Workshop Manual Correction - Fuel System Inspection (CAT. W, NO. 028/92)
  • Spark Plug Cross-Reference Chart (NO. T-1-3)
  • Parts Bulletin - Spark Plug Coil/Wire Set (NO. T-1-6)
  • 1.3/1.6L Eng Distributor Less IGN - Time Light Info (CAT. G, NO. 001/90)
  • 1.3L Eng Hard Cold Start - New Spark Plug (CAT. 5, NO. 018/88)
• Interior/Exterior Trim
  • Door Trim Recess Broken -Recess Available Separately (MT 0395-03)
• Interior/Illumination Lights
  • Room Lamp Does Not Illuminate - New Dome Light Bulb (CAT. T, NO. 016/97)
  • Acceptable Battery Drain (CAT. 5, NO. 017/88)
• Lubrication System
  • Oil Leak At Rear Stationary Gear O-Ring - Car Fix (B003/98)
  • Intake Manifold Gasket Precautions (CAT. F, NO. 005/95)
  • Intake Manifold Gasket Precautions (CANADIAN) (CAT. F, NO. 95-03)
  • Workshop Manual Correction - Fuel System Inspection (CAT. W, NO. 028/92)
  • 1.3L Eng Oil Leak - New Rear Engine Oil Seal/PROC (CAT. B, NO. 007/91)
  • Oil Leak - Rear Crankshaft Oil Seal Precaution (CAT. D, NO. 002/90)
  • Installing MAZDA Brand Oil Filter (CAT. 2, NO. 005/89)
• Manual Steering
  • Checking Procedure For Power Steering Boot Leakage (CAT. N, NO. 004/97)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • High Steering Wheel Effort - Verify Condition (MT 0995-05)
• Manual Trans
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Remanufactured Trans (CANADIAN) - Diagnosis Sheet (CAT. J, NO. 95-02)
  • Hard Shift, R-Type M/T: Modified Clutch Hub Assembly (CAT. J, NO. 93-03)
  • Hard Shift To 2ND Gear After Cold Start - New Parts (CAT. J, NO. 004/92)
  • Manual Transmission Shim Adjustments (CAT. J, NO. 001/90)
  • M & R Type Trans Hard Shift Cold - New Gear Oil (CAT. 7, NO. 062/89)
• Mechanical
  • Oil Leak At Rear Stationary Gear O-Ring - Car Fix (B003/98)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Revised ROTORY Engine Pricing (CAT. RF, NO. 95-24)
  • Intake Manifold Gasket Precautions (CAT. F, NO. 005/95)
  • Intake Manifold Gasket Precautions (CANADIAN) (CAT. F, NO. 95-03)
  • HLA Noise After Long Storage (CANADIAN) (CAT. B, NO. 95-04)
  • Partial Engine (Long Block) Availability (CAT. B, NO. 004/94)
  • Workshop Manual Correction - Fuel System Inspection (CAT. W, NO. 028/92)
  • 1.3L Eng Oil Leak - New Rear Engine Oil Seal/PROC (CAT. B, NO. 007/91)
  • Oil Leak - Rear Crankshaft Oil Seal Precaution (CAT. D, NO. 002/90)
  • Engine Stand ADAPTOR Modifications (CAT. 40, NO. 025/88)
  • 1.3L Eng Injector Air Bleed Socket Differences (CAT. 4, NO. 046/88)
• Mechanical - Hydraulic
  • Brake Rotor Machining And Replacement Criteria (CAT. P, NO. 001/96)
  • Brake Caliper Bolt Corrosion - Clean & Seal (MT 0995-11)
  • Brake Judder Repair (CANADIAN) (CAT. P, NO. 95-02)
  • Vibration/Pulsation While Braking - Procedure (CAT. P, NO. 006/94)
  • Brake Judder Repair ACCU Industries National Account (CAT. ST, NO, 003/94)
  • Revised Front Brake Pads Caliper & Hardware (CAT. 11, NO. 012/88)
• Memory Modules
  • Acceptable Battery Drain (CAT. 5, NO. 017/88)
• Mirrors
  • Door Mirror Vibration (CAT. S, NO. 020/95)
  • Power Antenna Mast Replacement (CANADIAN) (CAT. T, NO. 95-06)
  • Power Antenna Mast - Repair Procedure (MT 0195-08)
  • Convertible Top Operation/Troubleshooting (CAT. 15, NO. 076/89)
  • Improper Operation Of Power Window Regulator (CAT. 15, NO. 071/88)
• Paint & Coatings
  • Replacement Bumpers - Grease Removal Precautions (MT 08-03)
  • Water Soluble Transit Coating Removal Procedures (CAT. S, NO. 017/95)
  • Painting Rustproof Steel Panels (CAT. 14, NO. 070/89)
• Procedures
  • Carb Regulation (CALIFORNIA Only) - Mandatory Tire Pressure Check (MT-015/10)
• Rear Suspension
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Alignment Specifications And Tolerances -Information (CAT. N, NO. 004/94)
  • Alignment Specifications (CANADIAN) (CAT. N, NO. 95-02)
  • Excessive Rear Negative Camber: Replace Lower Arm (CAT. R, NO. 93-05)
  • Squeak In Front When Cold - New Front Strut Mount (CAT. R, NO. 004/90)
  • 1988 Front/Rear Wheel Alignment Specifications (CAT. 30, NO. 004/88)
  • Recommended Coil Spring Compressors (CAT. 40, NO. 019/87)
• Restraints Control Systems
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
• Seats
  • Dirt On Seat Belt And Anchor (CAT. S, NO. 028/96)
  • Power Antenna Mast Replacement (CANADIAN) (CAT. T, NO. 95-06)
  • Power Antenna Mast - Repair Procedure (MT 0195-08)
  • Availability Of Rear 3-Point Seat Belts (CAT. S, NO. 058/92)
  • Installation Of Rear 3-Point Seat Belt (CAT. 14, NO. 073/89)
  • Convertible Top Operation/Troubleshooting (CAT. 15, NO. 076/89)
  • Static Electricity Shock When Exiting Vehicle (CAT. 14, NO. 067/89)
  • Improper Operation Of Power Window Regulator (CAT. 15, NO. 071/88)
• Starter
  • All Models Except B-Series And NAVAJO - Dead Battery (Inspecting For Back-Up Current) (CAT. G, NO. 001/98)
  • Maintenance Free Battery-Revised Diag. & Charging (G001/97)
  • Battery Tester Recommendation - New National Account (CAT. ST, NO. 003/95)
  • Battery Recharging - Disconnect Negative Terminal (MT 08-10)
  • Warranty Bulletin - MAZDA Battery Warranty (CAT. G, NO. 1)
  • Battery Recharging Procedure (MT 0994-10)
  • Workshop Manual Correction - Fuel System Inspection (CAT. W, NO. 028/92)
• Steering Column
  • Steering Wheel Slightly Off Center - Procedure (CAT. N, NO. 005/95)
  • Alignment Specifications And Tolerances -Information (CAT. N, NO. 004/94)
  • Alignment Specifications (CANADIAN) (CAT. N, NO. 95-02)
• Steering Control Systems
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • High Steering Wheel Effort - Verify Condition (MT 0995-05)
• Steering Gear
  • Checking Procedure For Power Steering Boot Leakage (CAT. N, NO. 004/97)
• Steering Linkage
  • High Steering Wheel Effort - Verify Condition (MT 0995-05)
  • Alignment Specifications And Tolerances -Information (CAT. N, NO. 004/94)
  • Alignment Specifications (CANADIAN) (CAT. N, NO. 95-02)
• Sun Roof/T-Top/Convertible Top
  • Sunroof Failure: Modified Sliders & Realignment (CAT. 14, NO. 068/89)
  • Convertible Top Operation/Troubleshooting (CAT. 15, NO. 076/89)
• Suspension Control Systems
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • 1988 Front/Rear Wheel Alignment Specifications (CAT. 30, NO. 004/88)
• System
  • TAS (Throttle Adjustment Screw) Location/Adjustment (F014/98)
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • Oil Leak At Rear Stationary Gear O-Ring - Car Fix (B003/98)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • Intake Manifold Gasket Precautions (CAT. F, NO. 005/95)
  • Intake Manifold Gasket Precautions (CANADIAN) (CAT. F, NO. 95-03)
  • Shipment Of NGS Program Card Version 2.0:Information (CAT. ST, NO. 002/94)
  • Ecu/Air Flow Meter/Fuel Pump/Alternator Diagnostics (CAT. G, NO. 93-03)
  • Emission Inspection & Maintenance Test Preparations (CAT. F, NO. 005/93)
  • Workshop Manual Correction - Fuel System Inspection (CAT. W, NO. 028/92)
  • Spark Plug Cross-Reference Chart (NO. T-1-3)
  • Remanufactured EGI Control Unit Program (CAT. F, NO. 010/91)
  • 1.3L Eng Oil Leak - New Rear Engine Oil Seal/PROC (CAT. B, NO. 007/91)
  • Parts Bulletin - Spark Plug Coil/Wire Set (NO. T-1-6)
  • Oil Leak - Rear Crankshaft Oil Seal Precaution (CAT. D, NO. 002/90)
  • 1.3/1.6L Eng Distributor Less IGN - Time Light Info (CAT. G, NO. 001/90)
  • 1.3L Eng Hesitation At 6000 Rpm - New Air Flow Meter (CAT. 4, NO. 073/89)
  • Recommended Fuel (CAT. 4, NO. 054/89)
  • 1.3L Eng Hard Cold Start - New Spark Plug (CAT. 5, NO. 018/88)
  • 1.3L Eng EGI Control Unit Interchange Caution (CAT. 4, NO. 049/88)
  • 1.3L Eng Rough Idle - Damaged Water Temp Switch (CAT. 4, NO. 047/88)
  • 1.3L Eng Injector Air Bleed Socket Differences (CAT. 4, NO. 046/88)
  • 1.3L Eng Rough Idle Cold - Air Leak/Air Control VLV (CAT. 4, NO. 039/88)
  • Fuel Injector Color Code Table (CAT. 4, NO. 033/87)
• Towing
  • Vehicle Towing Precautions (CAT. AD, NO. 003/96)
• Transmission Control Systems
  • Inspection Procedure For Test Lead Of NGS Tester (CAT. ST, NO. 006/98)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Special Tools October 1995 - NGS Program Card (CAT. MC, NO. 96-01)
  • October 1995 Special Tools Shipment (CAT. ST, NO. 007/95)
  • Shipment Of NGS Program Card Version 2.0:Information (CAT. ST, NO. 002/94)
• Wheel Alignment
  • Alignment Specifications And Tolerances -Information (CAT. N, NO. 004/94)
  • Alignment Specifications (CANADIAN) (CAT. N, NO. 95-02)
• Wheels & Tire System
  • Carb Regulation (CALIFORNIA Only) - Mandatory Tire Pressure Check (MT-015/10)
  • MAZDA Required Tool (MRT) Inventory List (CAT. ST, NO. 004/96)
  • Installation Of Tire Chains (CAT. Q, NO. 005/93)
  • 1988 Front/Rear Wheel Alignment Specifications (CAT. 30, NO. 004/88)
  • MAZDA Wheel Lock Installation - Service Tip (02-001/06)
• Window Motors & Regulators
  • Wind Noise Around Doors (S018/98)
  • Windshield Stone Chipping Inspection (S037/96)
  • Power Antenna Mast Replacement (CANADIAN) (CAT. T, NO. 95-06)
  • Power Antenna Mast - Repair Procedure (MT 0195-08)
  • Convertible Top Operation/Troubleshooting (CAT. 15, NO. 076/89)
  • Improper Operation Of Power Window Regulator (CAT. 15, NO. 071/88)
• Wiper/Washer Systems
  • Front Wiper Motor Operation/Inspection (CAT. T, NO. 013/97)
  • Front Wiper Motor Inoperative (MT 0394-15)
  • Poor Wiper Blade Performance (CAT. A, NO. 93-07)
• Wiring System (Data Link Connectors, Pwr Dist., Grnd Dist.)
  • Acceptable Battery Drain (CAT. 5, NO. 017/88)