FixVault

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
A/C Compressor Bolt 13-20 (18-27)
A/C Compressor Bracket-To-Cylinder Block Bolt 27-38 (37-52)
Camshaft Sprocket Bolt 52-59 (71-80)
Connecting Rod Nut
Step 1 22 (30)
Step 2 Additional 90 Degrees
Crankshaft Pulley Bolt 116-123 (157-167)
Crossover Pipe-To-Exhaust Manifold Bolt 16-21 (22-29)
Cylinder Head Bolt (1)
Step 1 14 (19)
Step 2 Additional 90 Degrees
Step 3 Additional 90 Degrees
Delivery Pipe Nut 14-19 (19-26)
Distributor Hold-Down Bolt 14-19 (19-26)
Dynamic Chamber Nut 14-19 (19-26)
Engine Mount Bracket-To-Cylinder Block Bolt 29-42 (39-57)
Engine Mount Nut 25-36 (34-49)
Exhaust Manifold Nut 16-21 (22-29)
Exhaust Pipe-To-Exhaust Manifold Nut 25-36 (34-49)
Extension Manifold Nut 14-19 (19-26)
Flywheel/Drive Plate Bolt 76-81 (103-110)
Intake Air Pipe Bolt/Nut 14-19 (19-26)
Intake Manifold Nut (2) 14-19 (19-26)
Lower Idler Pulley Bolt 27-38 (37-52)
Main Bearing Cap Bolt (3)
Step 1 14 (19)
Step 2 Additional 90 Degrees
Step 3 Additional 45 Degrees
Oil Pressure Relief Valve Plug 56-65 (76-88)
Oil Pump Bolt 14-19 (19-26)
Power Steering Pump Bolt 23-34 (31-46)
Power Steering Pump Pulley Nut 29-43 (39-58)
Rocker Arm Shaft Bolt (4) 14-19 (19-26)
Stabilizer Bar-To-Frame Clamp Bolt 14-19 (19-26)
Tensioner Pulley Bolt 17-22 (23-30)
Thermostat Housing Bolt 14-19 (19-26)
Throttle Body Nut 14-19 (19-26)
Timing Belt Cover Bolt
6-mm Bolt (5)
10-mm Bolt 27-38 (37-52)
Timing Belt Tensioner Bolt 14-19 (19-26)
Transmission Crossmember-To-Frame Bolt 32-45 (43-61)
Transmission Mount-To-Crossmember Nut 23-34 (31-46)
Transmission-To-Cylinder Block Support Brace Bolt 27-38 (37-52)
Upper Idler Pulley Bolt 27-38 (37-52)
Water Pump Bolt/Nut 14-19 (19-26)
INCH Lbs. (N.m) 
A/C Pipe Bracket Bolt 61-87 (7-10)
Camshaft Thrust Plate Bolt 69-95 (8-11)
Cooling Fan Bolt/Nut 69-95 (8-11)
Distributor Spacer-To-Cylinder Head Bolt 69-95 (8-11)
Oil Baffle Plate Bolt 69-95 (8-11)
Oil Pan Bolt 61-87 (7-10)
Pick-Up Tube Bolt 69-95 (8-11)
Radiator Shroud Upper Plate Bolt 61-87 (7-10)
Seal Plate Bolt 69-95 (8-11)
Valve Cover Bolt 30-39 (3-4)
(1) Tighten bolts to specification in sequence. Figure .
(2) Tighten nuts to specification in sequence. Figure .
(3) Tighten bolts to specification in sequence. Figure .
(4) Tighten bolts to specification in sequence. Figure .
(5) Tighten to 69-95 INCH lbs. (8-11 N.m).