When idling can be continued
If simulation function of M-MDS is used:
- Warm up the engine to normal operating temperature.
- Connect the M-MDS to the DLC-2.
- Verify that DTC P2090:00 or P2091:00 is displayed. Refer too ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)]
.)
- Perform the DTC inspection. Refer too DTC P2090:00 [PCM (SKYACTIV-G 2.5T)] .) Refer too DTC P2091:00 [PCM (SKYACTIV-G 2.5T)] .)
- Start the engine and let it idle.
- Access the simulation item VT_EX_DES using the M-MDS. Refer too ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)] .)
- Increase the OCV duty value and verify that the engine idles rough or stalls.
- If the engine idles rough or stalls, inspect the timing chain component (valve timing deviation). Refer too HYDRAULIC VARIABLE VALVE TIMING ACTUATOR INSPECTION [SKYACTIV-G 2.5T] .)
- If the engine does not idle rough or stalls, go to the next step.
- Remove the OCV while the connector is connected. Refer too OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION [SKYACTIV-G 2.5T] .)
- Switch the ignition ON (engine off).
- Access the simulation item VT_EX_DES using the M-MDS. Refer too ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)] .)
- Increase the OCV duty value and verify that the spool valve operates in the retard direction.
- If as specified, inspect the following hydraulic passage for restriction and/or leakage:
- Oil pressure switch-OCV
- OCV-Camshaft
- Camshaft internal passage
- If not as specified, inspect the following:
- OCV operation Refer too OIL CONTROL VALVE (OCV) INSPECTION [SKYACTIV-G 2.5T] .)
- If as specified, inspect the following hydraulic passage for restriction and/or leakage:
- If they are normal, replace the hydraulic variable valve timing actuator. Refer too ELECTRIC VARIABLE VALVE TIMING ACTUATOR, HYDRAULIC VARIABLE VALVE TIMING ACTUATOR REMOVAL/INSTALLATION [SKYACTIV-G 2.5T]
.)
If simulation function of M-MDS is not used:
- Disconnect the OCV connector. Refer too OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION [SKYACTIV-G 2.5T] .)
- Warm up the engine and idle it.
- Apply the battery voltage to the OCV and verify that the engine idles rough or stalls.
- If the engine idles rough or stalls, inspect the timing chain component (valve timing deviation). Refer too HYDRAULIC VARIABLE VALVE TIMING ACTUATOR INSPECTION [SKYACTIV-G 2.5T] .)
- If the engine does not idle rough or stalls, go to the next step.
- Remove the OCV and perform the Spool Valve Operation Inspection. Refer too OIL CONTROL VALVE (OCV) INSPECTION [SKYACTIV-G 2.5T]
.)
- If not as specified, inspect the following:
- OCV Refer too OIL CONTROL VALVE (OCV) INSPECTION [SKYACTIV-G 2.5T] .)
- Harnesses and connectors between OCV and PCM have an open or short circuit
- If as specified, inspect the following hydraulic passages for restriction or leakage or both:
- Oil pressure switch-OCV
- OCV-Camshaft
- Camshaft internal passage
- If not as specified, inspect the following:
- If they are normal, replace the hydraulic variable valve timing actuator. Refer too ELECTRIC VARIABLE VALVE TIMING ACTUATOR, HYDRAULIC VARIABLE VALVE TIMING ACTUATOR REMOVAL/INSTALLATION [SKYACTIV-G 2.5T] .)