FixVault
Home › Mazda › 2019 › CX-9 Signature › Repair and Diagnosis › Body & Frame › Door Locks › On-Board Diagnostic - Start Stop Unit › DTC Table

DTC Table

Immobilizer System

x: Applicable-: Not applicable

DTC DESCRIPTION (START STOP UNIT)

DTC KEY warning light (red) (2) Multi-information display(3) Push button start indicator light (amber) Description Fail-safe Drive cycle Self test type(4) Memory function Refer to
M-MDS display(1)     Security indicator light flash pattern
Start stop unit     PCM
U3000:96 P1260:00 09
G13447381Courtesy of MAZDA MOTORS CORP.
 On Display Flash Start stop unit malfunction - - C x (See SECURITY INDICATOR LIGHT: 09, DTC: U3000:96/P1260:00 [START STOP UNIT] .)
B10D9:87 P1260:00 11
G13447382Courtesy of MAZDA MOTORS CORP.
 - - Flash Coil antenna (built into push button start) error - - C - (See SECURITY INDICATOR LIGHT: 11, DTC: B10D9:87/P1260:00 [START STOP UNIT] .)
B13D3:05 P1260:00 13
G13447383Courtesy of MAZDA MOTORS CORP.
 - - - Remote transmitter program error - - C - (See SECURITY INDICATOR LIGHT: 13, DTC: B13D3:05/P1260:00 [START STOP UNIT] .)
B13D3:94 P1260:00 13   - - - Communication error with remote transmitter - - C - (See SECURITY INDICATOR LIGHT: 13, DTC: B13D3:94/P1260:00 [START STOP UNIT] .)
B13D3:51 P1260:00 15
G13447384Courtesy of MAZDA MOTORS CORP.
 - - Flash Unregistered remote transmitter is detected - - C - (See SECURITY INDICATOR LIGHT: 15, DTC: B13D3:51/P1260:00 [START STOP UNIT] .)
U0100:87 P1260:00 16
G13447385Courtesy of MAZDA MOTORS CORP.
 - - - Communication error with PCM (no response or data mismatch) - - C - (See SECURITY INDICATOR LIGHT: 16, DTC: U0100:87/P1260:00 [START STOP UNIT] .)
B13D4:00 P1260:00 21
G13447386Courtesy of MAZDA MOTORS CORP.
 On Display - Insufficient remote transmitter programming number - - C - (See SECURITY INDICATOR LIGHT: 21, DTC: B13D4:00/P1260:00 [START STOP UNIT] .)
B10DA:51 P1260:00 22
G13447387Courtesy of MAZDA MOTORS CORP.
 - - - Communication error with PCM (data received failure) - - C - (See SECURITY INDICATOR LIGHT: 22, DTC: B10DA:51/P1260:00 [START STOP UNIT] .)
B10DA:62 P1260:00 23
G13447388Courtesy of MAZDA MOTORS CORP.
 - - - Communication error with PCM (code mis-matched) - - C - (See SECURITY INDICATOR LIGHT: 23, DTC: B10DA:62/P1260:00 [START STOP UNIT] .)
(1) The letters at the beginning of each DTC are only displayed when using the M-MDS, and refer to the following: B= Body system, P= Powertrain system, U= Network communication system.
(2) Without multi-information display
(3) "Keyless system malfunction" is displayed in the multi-information display. (With multi-information display)
(4) C: CMDTC self test, D: ODDTC self test

Advanced Keyless Entry System (With Advanced Keyless Entry System)

x: Applicable-: Not applicable

ADVANCED KEYLESS ENTRY SYSTEM DESCRIPTION (WITH ADVANCED KEYLESS ENTRY SYSTEM)

DTC No. KEY warning light (red)(1) Multi-information display(2) Push button start indicator light (amber) Description Fail safe Drive cycle Self test type(3) Memory function Refer to
B10C6:1F On Display - Keyless antenna (exterior, rear) circuit malfunction x - C, D x (See DTC B10C6:1F [START STOP UNIT] .)
B10C7:1F On Display - Keyless antenna (interior, rear) circuit malfunction x - C, D x (See DTC B10C7:1F [START STOP UNIT] .)
B10C8:1F On Display - Keyless antenna (interior, center) circuit malfunction x - C, D x (See DTC B10C8:1F [START STOP UNIT] .)
B10C9:1F On Display - Keyless antenna (interior, front) circuit malfunction x - C, D x (See DTC B10C9:1F [START STOP UNIT] .)
B10D1:23 On Display - Request switch (LF) circuit malfunction - - C x (See DTC B10D1:23 [START STOP UNIT] .)
B10D3:23 On Display - Request switch (RF) circuit malfunction - - C x (See DTC B10D3:23 [START STOP UNIT] .)
B11C4:23 On Display - Request switch (liftgate) circuit malfunction - - C x (See DTC B11C4-23: [START STOP UNIT] .)
B11FD:1F On Display - Keyless antenna (exterior, LF) circuit malfunction x - C, D x (See DTC B11FD:1F [START STOP UNIT] .)
B1210:1F On Display - Keyless antenna (exterior, RF) circuit malfunction x - C, D x (See DTC B1210:1F [START STOP UNIT] .)
B13C3:04 On Display - LF control unit internal malfunction x - C x (See DTC B13C3:04 [START STOP UNIT] .)
B13C3:09 On Display - LF control unit malfunction x - C x (See DTC B13C3:09 [START STOP UNIT] .)
B13C3:16 On Display - LF control unit power supply voltage low input x - C x (See DTC B13C3:16 [START STOP UNIT] .)
B13C3:29 On Display - Communication error between start stop unit and LF control unit x - C x (See DTC B13C3:29 [START STOP UNIT] .)
(1) Without multi-information display
(2) "Keyless system malfunction" is displayed in the multi-information display. (With multi-information display)
(3) C: CMDTC self test, D: ODDTC self test

Start Stop Unit

x: Applicable-: Not applicable

START STOP UNIT DESCRIPTION

DTC No. KEY warning light (red)(1) Multi-information display(2) Push button start indicator light (a mb er) Description Fail-safe Drive cycle Self test type (3) Memory function Refer to
B108B:23 - - Flash Push button start switch 1 circuit malfunction x - C x (See DTC B108B:23 [START STOP UNIT] .)
B108B:24 - - Flash Push button start switch 1 circuit malfunction - - C x (See DTC B108B:24 [START STOP UNIT] .)
B108C:23 - - Flash Push button start switch 2 circuit malfunction x - C x (See DTC B108C:23 [START STOP UNIT] .)
B108C:24 - - Flash Push button start switch 2 circuit malfunction - - C x (See DTC B108C:24 [START STOP UNIT] .)
B10AC:13 (4) - - - Cruise control switch circuit malfunction - - C x (See DTC B10AC:13 [START STOP UNIT] .)
B10AC:23 (4) - - - Cruise control switch circuit malfunction - - C x (See DTC B10AC:23 [START STOP UNIT] .)
B10C9:1F (5) On Display - Keyless antenna (interior, center) circuit malfunction - - C, D x (See DTC B10C9:1F [START STOP UNIT] .)
B10E7:11 - - Flash IG1 relay circuit malfunction - - C x (See DTC B10E7:11 [START STOP UNIT] .)
B10E7:12 - - Flash IG1 relay circuit malfunction - - C x (See DTC B10E7:12 [START STOP UNIT] .)
B10E7:16 - - Flash IG1 relay circuit malfunction - - C x (See DTC B10E7:16 [START STOP UNIT] .)
B10E7:17 - - Flash IG1 relay circuit malfunction - - C x (See DTC B10E7:17 [START STOP UNIT] .)
B112A:11 - - Flash IG2 relay circuit malfunction - - C x (See DTC B112A:11 [START STOP UNIT] .)
B112A:12 - - Flash IG2 relay circuit malfunction - - C x (See DTC B112A:12 [START STOP UNIT] .)
B124C:56 - - - Turn switch internal circuit malfunction - - C x (See DTC B124C:56 [START STOP UNIT] .)
B13D3:16 - - - Low remote transmitter battery voltage - - C x (See DTC B13D3:16 [START STOP UNIT] .)
B13D3:4A On Display - Remote transmitter matching malfunction - - C x (See DTC B13D3:4A [START STOP UNIT] .)
B13D3:97 - - - Remote transmitter registration work not completed - - C x (See DTC B13D3:97 [START STOP UNIT] .)
B1C53:13 - - - Winds hield wiper switch circuit malfunction - - C x (See DTC B1C53:13 [START STOP UNIT] .)
C0040:23 - - Flash Brake switch (No. 1 signal) circuit malfunction x - C x (See DTC C0040:23 [START STOP UNIT] .)
C0040:24 - - Flash Brake switch (No. 1 signal) circuit malfunction x - C x (See DTC C0040:24 [START STOP UNIT] .)
C0051:2F (6) - - - Steering angle sensor signal error - - C x (See DTC C0051:2F [START STOP UNIT] .)
C0051:95 (6) - - - Steering angle sensor assembly malfunction - - C x (See DTC C0051:95 [START STOP UNIT] .)
C0052:14 (6) - - - Steering angle sensor A signal circuit malfunction - - C x (See DTC C0052:14 [START STOP UNIT] .)
C0052:2F (6) - - - Steering angle sensor A signal malfunction - - C x (See DTC C0052:2F [START STOP UNIT] .)
C0053:14 (6) - - - Steering angle sensor B signal circuit malfunction - - C x (See DTC C0053:14 [START STOP UNIT] .)
C0053:2F (6) - - - Steering angle sensor B signal malfunction - - C x (See DTC C0053:2F [START STOP UNIT] .)
C2003:13 (7) - - - Open circuit in steering switch - - C x (See DTC C2003:13 [START STOP UNIT] .)
P0615:11 - - Flash Starter relay circuit malfunction - - C x (See DTC P0615:11 [START STOP UNIT] .)
P0615:12 - - Flash Starter relay circuit malfunction x - C x (See DTC P0615:12 [START STOP UNIT] .)
P0615:13 - - Flash Starter relay circuit malfunction - - C x (See DTC P0615:13 [START STOP UNIT] .)
P0615:16 - - Flash Starter relay circuit malfunction - - C x (See DTC P0615:16 [START STOP UNIT] .)
P0616:23 - - - Circuit malfunction on downs tream side of starter relay - - C x (See DTC P0616:23 [START STOP UNIT] .)
P0616:24 - - - Circuit malfunction on downs tream side of starter relay - - C x (See DTC P0616:24 [START STOP UNIT] .)
P0616:29 - - - Downs tream side of starter relay signal malfunction - - C x (See DTC P0616:29 [START STOP UNIT] .)
P081C:23 - - Flash NOT P position switch circuit malfunction x - C x (See DTC P081C:23 [START STOP UNIT] .)
P081C:24 - - Flash NOT P position switch circuit malfunction x - C x (See DTC P081C:24 [START STOP UNIT] .)
P0850:23 - - Flash Transaxle range sensor circuit malfunction x - C x (See DTC P0850:23 [START STOP UNIT] .)
P0850:24 - - Flash Transaxle range sensor circuit malfunction x - C x (See DTC P0850:24 [START STOP UNIT] .)
P0930:71 - - - Shift-lock solenoid circuit malfunction x - C x (See DTC P0930:71 [START STOP UNIT] .)
P1794:16 - - Flash Start stop unit power supply voltage (terminal 2W) low input - - C x (See DTC P1794:16 [START STOP UNIT] .)
U0001:88 On Display Flash Module communication error (HS-CAN) x - C x (See DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U0151:00/U0155:00 [START STOP UNIT] .)
U0028:87 On Display - Communication error with rear body control module (RBCM) x - C x (See DTC U0028:87 [START STOP UNIT] .)
U0100:00 On Display Flash Communication error with PCM x - C x (See DTC U0001:88/U0100:00/U0101:00/U0121:00/U0121:87/U0131:00/U0140:00/U0146:00/U015 1:00/U0155:00 [START STOP UNIT] .)
U0101:00 - - Flash Communication error with TCM x - C x
U0121:00 On Display Flash Communication error with DSC HU/C M x - C x
U0121:87 On Display Flash Communication error with DSC HU/C M x - C x
U0131:00 - - - Communication error with electric power steering (EPS) control module x - C x
U0140:00 - - - Communication error with front body control module (FBCM) x - C x
U0146:00 On Display Flash Communication error with instrument cluster x - C x
U0151:00 On Display Flash Communication error with SAS control module x - C x
U0155:00 On Display Flash Communication error with instrument cluster x - C x
U0447:86 On Display Flash Error signal received from instrument cluster x - C x (See DTC U0447:86 [START STOP UNIT] .)
U201F:11 On Display - Keyless receiver circuit malfunction - - C x (See DTC U201F:11 [START STOP UNIT] .)
U201F:12 On Display - Keyless receiver circuit malfunction - - C x (See DTC U201F:12 [START STOP UNIT] .)
U2100:00 On Display - Start stop unit configuration not completed x - C x (See DTC U2100:00 [START STOP UNIT] .)
U2300:00 - - - Configuration data not received from instrument cluster x - C x (See DTC U2300:00 [START STOP UNIT] .)
U3000:01 (6) - - - Start stop unit internal malfunction - - C x (See DTC U3000:01 [START STOP UNIT] .)
U3000:49 On Display Flash Start stop unit internal malfunction x - C x (See DTC U3000:49 [START STOP UNIT] .)
U3000:96 On Display Flash Start stop unit malfunction - - C x (See DTC U3000:96 [START STOP UNIT] .)
U3003:16 On Display - Start stop unit power supply voltage (terminal 1A) low input x - C x (See DTC U3003:16 [START STOP UNIT] .)
U3004:11 - - Flash ACC relay circuit malfunction - - C x (See DTC U3004:11 [START STOP UNIT] .)
U3004:12 - - Flash ACC relay circuit malfunction - - C x (See DTC U3004:12 [START STOP UNIT] .)
U3004:16 - - - ACC relay circuit malfunction - - C x (See DTC U3004:16 [START STOP UNIT] .)
U3004:17 - - - ACC relay circuit malfunction - - C x (See DTC U3004:17 [START STOP UNIT] .)
(1) Without multi-information display
(2) "Keyless system malfunction" is displayed in the multi-information display. (With multi-information display)
(3) C: CMDTC self test, D: ODDTC self test
(4) With cruise control system
(5) With keyless entry system
(6) With adaptive front lighting system (AFS) or with smart brake support (SBS)
(7) With steering switch
About FixVault