FixVault
Home › Mazda › 2021 › MX-5 Miata Club, Automatic Trans › Repair and Diagnosis › Accessories & Equipment › Communication Devices › On-Board Diagnostic - Body Control Module (BCM) › PID/Data Monitor Table

PID/Data Monitor Table

NOTE:
  • The "Type" in the PID/data monitor table is indicated as follows.
  • Input: Value input to module
  • Conversion: Value converted into value input to module
  • Calculation: Value calculated for several input values in module
  • Output: Value output by module

-: Not applicable

PID/DATA MONITOR DESCRIPTION

Item Unit Type Content Operation status (reference) Terminal
ABK_HD_CS_R Off/On If an accessory part is installed, it cannot be used.
ABK_HN_CS_R Off/On If an accessory part is installed, it cannot be used.
AMBI_TEMP (1) °C,°F
NOTE:
  • Displayed on M-MDS but does not function.
AMBI_TEMP_A (1) OK/NG
NOTE:
  • Displayed on M-MDS but does not function.
BG_HORN_RLY Off/On If an accessory part is installed, it cannot be used.
BLWR_RLY Off/On Output Displays the blower relay operation status.
  • Off: Blower relay is off (ignition is switched off)
  • On: Blower relay is on (ignition is switched ON)
 3E
BRAKE_SW Off/On
NOTE: Displayed on M-MDS but does not function.
BRK_F_L_SW Off (Normal)/On (Low) Conversion Displays the brake fluid level status.
  • Off (Normal): Brake fluid level is between MAX and MIN
  • On (Low): Brake fluid level is lower than MIN
 3R
C_DL_SW_LK Off/On Conversion Displays the door lock switch operation status (lock operation).
  • Off: Door lock switch is not in lock
  • On: Door lock switch is in lock
 2K
C_DL_SW_UNL Off/On Conversion Displays the door lock switch operation status (unlock operation).
  • Off: Door lock switch is not in unlock
  • On: Door lock switch is in unlock
 2K
DOOR_ALL Close/OPEN Conversion Displays all the doors open/closed condition.
  • Close: All doors are closed
  • OPEN: Any door is open
 2H/2G
DOOR_D Close/OPEN Conversion Displays the door (LH) open/closed condition.
  • Close: Door (LH) is closed
  • OPEN: Door (LH) is open
 2H
DOOR_LR Close/OPEN
NOTE:
  • Displayed on M-MDS but does not function.
DOOR_P Close/OPEN Conversion Displays the door (RH) open/closed condition.
  • Close: Door (RH) is closed
  • OPEN: Door (RH) is open
 2G
DOOR_RR Close/OPEN
NOTE:
  • Displayed on M-MDS but does not function.
DOOR_TL (2) Close/OPEN Conversion Convertible top open/closed condition.
  • Close: Convertible top is closed
  • OPEN: Convertible top is open
 2E
DR_LK_RY Off/On Output Displays the door lock relay operation request (lock signal) send status. The BCM sends a lock signal to the electrical supply unit (ESU) via LIN communication.
  • Off: Lock signal is not sent (lock operation is not operated)
  • On: Lock signal is sent (lock operation is operated)
 2Y
DR_UNLK_RY Off/On Output Displays the door unlock relay operation request (unlock signal) send status. The BCM sends an unlock signal to the electrical supply unit (ESU) via LIN communication.
  • Off: Unlock signal is not sent (unlock operation is not operated)
  • On: Unlock signal is sent (unlock operation is performed)
 2Y
F_FOG_RELAY Off/On
NOTE: Displayed on M-MDS but does not function.
F_FOG_SW Off/On
NOTE: Displayed on M-MDS but does not function.
FUEL_SEN_HM V
NOTE: Displayed on M-MDS but does not function.
FUEL_SEN_HS V
NOTE: Displayed on M-MDS but does not function.
FUEL_SEN_HV V
NOTE: Displayed on M-MDS but does not function.
FUEL_SEN_M V Input Displays the fuel gauge sender unit input voltage. If the fuel tank level is low, the BCM input voltage increases because the fuel gauge sender unit resistance increases. Displays the fuel gauge sender unit voltage. 2Q
FUEL_SEN_S V
NOTE: Displayed on M-MDS but does not function.
FUEL_SEN_V V Input Displays the fuel gauge sender unit supply voltage. Ignition switched ON (engine off): Approx. 4.15 V 1A/1B
H/L_CLN_RY Off/On
NOTE: Displayed on M-MDS but does not function.
H/L_CS_RLS Off/On Conversion Displays the headlight LO on request signal reception status. The BCM receives a headlight LO on request signal via LIN communication from the autolight sensor/rain sensor.
NOTE:
  • When the auto-light sensor/rain sensor detects the average 2, 000 lux or less per 1 min for upward illumination, it sends a headlight LO on request signal to the BCM.
  • Off: Headlight LO on request signal is not received
  • On: Headlight LO on request signal is received
 3X
H/L_DRL Off/On Output Displays the running light on request signal send status. The BCM sends a running light on request signal to the electrical supply unit (ESU) via LIN communication.
NOTE:
  • For the specific operation condition of the PID "H/L_DRL", refer to the "DAYTIME RUNNING LIGHT (DRL) SYSTEM" for new vehicle instruction.
  • Off: Running light on request signal is not sent
  • On: Running light on request signal is sent
 2Y
H/L_HI % Output Displays the headlight HI on request signal send status. The BCM sends a headlight HI on request signal to the electrical supply unit (ESU) via LIN communication.
  • Headlight HI on request signal is not sent (headlight high beam turns off): 0 %
  • Headlight HI on request signal is sent (headlight high beam turns on): 100 %
 2Y
H/L_LOW % Output Displays the headlight LO on request signal send status. The BCM sends a headlight LO on request signal to the electrical supply unit (ESU) via LIN communication.
  • Headlight LO on request signal is not sent (headlight low beam turns off): 0 %
  • Headlight LO on request signal is sent (headlight low beam turns on): 100 %
 2Y
H/L_PASS Off/On Output Displays the headlight LO and HI on request signal send status. The BCM sends a headlight LO and HI on request signal to the electrical supply unit (ESU) via LIN communication.
  • Off: Headlight LO and HI on request signal is not sent (no passing)
  • On: Headlight LO and HI on request signal is sent (passing)
 2Y
H/L_SW_HI Off/On Conversion Displays the light switch (HI position) operation status. The BCM receives a light switch (HI position) input signal via CAN communication from the start stop unit.
  • Off: Light switch (HI position) OFF signal is received
  • On: Light switch (HI position) ON signal is received
 2C/2D
H/L_SW_LOW Off/On Conversion Displays the light switch (LO position) operation status. The BCM receives a light switch (LO position) input signal via CAN communication from the start stop unit.
  • Off: Light switch (LO position) off signal is received
  • On: Light switch (LO position) on signal is received
 2C/2D
H/L_SW_OFF Off/On Conversion Displays the light switch (OFF position) operation status. The BCM receives a light switch (OFF position) input signal via CAN communication from the start stop unit.
  • Off: Light switch (OFF position) off signal is received
  • On: Light switch (OFF position) on signal is received
 2C/2D
H/L_SW_PASS Off/On Conversion Displays the light switch (passing position) operation status. The BCM receives a light switch (passing position) input signal via CAN communication from the start stop unit.
  • Off: Light switch (passing position) off signal is received
  • On: Light switch (passing position) on signal is received
 2C/2D
H/L_SW_TNS Off/On Conversion Displays the light switch (TNS (parking lights) position) operation status. The BCM receives a light switch (TNS (parking lights) position) input signal via CAN communication from the start stop unit.
  • Off: Light switch (TNS (parking lights) position) off signal is received
  • On: Light switch (TNS (parking lights) position) on signal is received
 2C/2D
H/L_TNS Off/Right-On/Left-On/On Output Displays the TNS (parking lights) on request signal send status. The BCM sends a TNS (parking lights) on request signal to the electrical supply unit (ESU) via LIN communication.
  • Off: TNS (parking lights) on request signal is not sent (light switch is in position other than TNS (parking lights))
  • Right-On: Parking light (RH) is forcibly operated using simulation item
  • Left-On: Parking light (LH) is forcibly operated using simulation item
  • On: TNS (parking lights) on request signal is sent (light switch is in TNS (parking lights) position)
 2Y
H/L_TNS_RLS Off/On Conversion Displays the TNS (parking lights) on request signal reception status. The BCM receives a TNS (parking lights) on request signal via LIN communication from the autolight sensor/rain sensor.
NOTE:
  • When the auto-light sensor/rain sensor detects the average 2, 000 lux or less per 1 min for upward illumination, it sends a TNS (parking lights) on request signal to the BCM.
  • Off: TNS (parking lights) on request signal is not received
  • On: TNS (parking lights) on request signal is received
 3X
H/L_TYPE Halogen_2Lights/Halogen_4Lights/Lo-HIDHi-Hlogen_4Lights/LED_4Lights/Bi-Xenon - Displays the type of headlight equipped to the vehicle. The BCM sends information concerning the type of headlight to the electrical supply unit (ESU) via LIN communication. - 2Y
HAZARD_SW Off/On/Unknown Conversion Displays the hazard warning operation status. The BCM receives a hazard warning switch input signal via CAN communication from the start stop unit.
  • Off: Hazard warning switch off signal is received (hazard warning switch is not pressed)
  • On: Hazard warning switch on signal is received (hazard warning switch is pressed)
  • Unknown: Signal which hazard warning switch position is not determined is received
 2C/2D
HOOD (3) Close/OPEN Conversion Displays the hood latch switch operation status.
  • Close: Hood latch switch is on (hood is closed)
  • OPEN: Hood latch switch is off (hood is open)
 3W
HORN_RLY Off/On Output Displays the horn relay operation status.
  • Off: Horn relay is off (horn switch is not pressed)
  • On: Horn relay is on (horn switch is pressed)
 3H
IG1_STATUS IG-Off/IG-On Conversion Displays the IG1 power supply input status determined in the BCM.
  • IG-Off: IG1 power is not input to BCM
  • IG-On: IG1 power is input to BCM
 3O
KC_SW_D_LK Off/On Conversion Displays the door key cylinder switch operation status (lock operation).
  • Off: Door key cylinder switch is not in lock (lock operation is not performed using door key cylinder)
  • On: Door key cylinder switch is in lock (lock operation is performed using door key cylinder)
 2L
KC_SW_D_UNL Off/On Conversion Displays the door key cylinder switch operation status (unlock operation).
  • Off: Door key cylinder switch is not in unlock (unlock operation is not performed using door key cylinder)
  • On: Door key cylinder switch is in unlock (unlock operation is performed using door key cylinder)
 2L
LIGHT_SEN (1) - Input Displays the illumination level in front of the vehicle. - 3X
LIGHT_SEN_A (1) OK/NG Input Displays the forward illumination sensor signal determination status.
  • OK: Forward illumination sensor signal is valid
  • NG: Forward illumination sensor signal is invalid
 3X
LL_SW_D_LK Off/On Conversion Displays the door lock-link switch (LH) operation status (lock operation).
  • Off: Door lock-link switch (LH) is not in lock (lock operation is not performed using driver's door lock knob)
  • On: Door lock-link switch (LH) is in lock (lock operation is performed using driver's door lock knob)
 2A
LL_SW_D_UNL Off/On Conversion Displays the door lock-link switch (LH) operation status (unlock operation).
  • Off: Door lock-link switch (LH) is not in lock (unlock operation is not performed using driver's door lock knob)
  • On: Door lock-link switch (LH) is in unlock (unlock operation is performed using driver's door lock knob)
 2B
LL_SW_P/R Off/On Conversion Displays the door lock-link switch (RH) operation status (lock operation).
  • Off: Door lock-link switch (RH) is not in lock (lock operation is not performed using passenger's door lock knob)
  • On: Door lock-link switch (RH) is in lock (lock operation is performed using passenger's door lock knob)
 2M
PNC_HD_CS_R Off/On If an accessory part is installed, it cannot be used.
PNC_HN_CS_R Off/On If an accessory part is installed, it cannot be used.
PTC_HEAT_ST %
NOTE: Displayed on M-MDS but does not function.
R_DEF_RLY Off/On Output Displays the rear window defogger relay operation status.
  • Off: Rear window defogger relay is off (rear window defogger switch is not pressed)
  • On: Rear window defogger relay is on (rear window defogger switch is pressed)
 3K
R_FOG_LAMP Off/On
NOTE: Displayed on M-MDS but does not function.
R_FOG_SW Off/On
NOTE: Displayed on M-MDS but does not function.
REL_HUM (1) %
NOTE: Displayed on M-MDS but does not function.
REL_HUM_A (1) OK/NG
NOTE: Displayed on M-MDS but does not function.
REVERSE_LMP Off/On Output Displays the backup light on request signal send status. The BCM sends a back-up light on request signal to the electrical supply unit (ESU) via LIN communication.
  • Off: Back-up light on request signal is not sent (MT: shift lever is not in reverse position, AT: selector lever is not in R position)
  • On: Back-up light on request signal is sent (MT: shift lever is in reverse position, AT: selector lever is in R position)
 2Y
ROOM_LAMP Off/100%_On/60%_On/50%_On/40%_On/30%_On/20%_On Output Displays the map light on request signal send status. The BCM sends a map light on request signal to the electrical supply unit (ESU) via LIN communication.
NOTE:
  • For the specific operation condition of the PID "ROOM_LAMP", refer to the "ROOM LIGHT CONTROL SYSTEM" for new vehicle instruction.
  • Off: Map light on request signal is not sent
  • 100%_On: Map light on request signal (100%) is sent
  • 60%_On: Map light on request signal (60%) is sent
  • 50%_On:-
  • 40%_On:-
  • 30%_On:-
  • 20%_On:-
 2Y
SEAT_B_2C Unbuckled/Buckled
NOTE: Displayed on M-MDS but does not function.
SEAT_B_2L Unbuckled/Buckled
NOTE: Displayed on M-MDS but does not function.
SEAT_B_2R Unbuckled/Buckled
NOTE: Displayed on M-MDS but does not function.
SEAT_B_3C Unbuckled/Buckled
NOTE: Displayed on M-MDS but does not function.
SEAT_B_3L Unbuckled/Buckled
NOTE: Displayed on M-MDS but does not function.
SEAT_B_3R Unbuckled/Buckled
NOTE: Displayed on M-MDS but does not function.
STOP_LAMP_DSC Unknown/Off/On/Backup_On
NOTE: Displayed on M-MDS but does not function.
STOP_LMP_CTL Off/On
NOTE: Displayed on M-MDS but does not function.
STOP_LMP_IN Off/On
NOTE: Displayed on M-MDS but does not function.
TR_UNL_SW Off/On Conversion Displays the trunk lid opener switch (exterior) operation status.
  • Off: Trunk lid opener switch is off (trunk lid opener switch (exterior) is not pressed)
  • On: Trunk lid opener switch is on (trunk lid opener switch is pressed)
 2S
TR_UNL_SW_IP Off/On Conversion Displays the trunk lid opener switch (interior) operation status.
  • Off: Trunk lid opener switch (interior) is off (trunk lid opener switch (interior) is not pressed)
  • On: Trunk lid opener switch (interior) is on (trunk lid opener switch (interior) is pressed)
 2AC
TRUNK Close/OPEN Conversion Displays the trunk lid latch switch operation status.
  • Close: Trunk lid latch switch is off (trunk is closed)
  • OPEN: Trunk lid latch switch is on (trunk is open)
 2AC
TRUNK_LAMP Off/On Output Displays the trunk compartment light on request signal send status. The BCM sends a trunk compartment light on request signal to the electrical supply unit (ESU) via LIN communication.
  • Off: Trunk compartment light on request signal is not sent (trunk is closed)
  • On: Trunk compartment light on request signal is sent (trunk is open)
 2Y
TRUNK_MOTOR Off/On Output Displays the trunk lid release signal send status. The BCM sends a trunk lid release signal to the electrical supply unit (ESU) via LIN communication.
  • Off: Trunk lid release signal is not sent (trunk lid opener switch is not pressed)
  • On: Trunk lid release signal is sent (trunk lid opener switch is pressed)
 2Y
TURN_L_L Off/On Output Displays the turn light (LH) operation status.
  • Off: Turn light (LH) turns off (turn switch is in OFF position)
  • On: Turn light (LH) flashes (turn switch is in LH position)
 1G/3B
TURN_L_R Off/On Output Displays the turn light (RH) operation status.
  • Off: Turn light (RH) turns off (turn switch is in OFF position)
  • On: Turn light (RH) flashes (turn switch is in RH position)
 1E/3A
TURN_SW Off/Turn_R_On/Turn_L_On/Unknown Conversion Displays the turn switch operation status. The BCM receives a turn switch input signal via CAN communication from the start stop unit.
  • Off: Turn switch off signal is received (turn switch is in OFF position)
  • Turn_R_On: Turn switch RH signal is received (turn switch is in RH position)
  • Turn_L_On: Turn switch LH signal is received (turn switch is in LH position)
  • Unknown: Signal which turn switch position is not determined is received
 2C/2D
VPWR V Input Displays the BCM supply voltage. Switch the ignition ON (engine off):Approx. 12 V 1A
VPWR_B_H V Input Displays the BCM supply voltage. Switch the ignition ON (engine off):Approx. 12 V 1A
VSPD KPH, MPH Output Displays the vehicle speed. The BCM sends a vehicle speed signal to the autolight sensor/rain sensor via LIN communication. - 3X
WASHER_CTRL Off/Front/Rear Output Displays the washer operation request signal send status. The BCM sends a washer operation request signal to the electrical supply unit (ESU) via LIN communication.
  • Off: Washer operation request signal is not sent (washer is not operating)
  • Front: Washer operation request signal is sent (washer switch is in ON position)
  • Rear: -
 2Y
WASHER_F_SW Off/On Conversion Displays the washer switch operation status. The BCM receives a washer switch input signal via CAN communication from the start stop unit.
  • Off: Washer switch off signal is received (washer switch is in OFF position)
  • On: Washer switch on signal is received (washer switch is in ON position)
 2C/2D
WASHER_FLD Off (Normal)/On (Low) Conversion Displays the washer fluid level status.
  • Off (Normal): Washer fluid level is normal
  • On (Low): Washer fluid level is low
 3Q
WASHER_R_SW Off/On
NOTE: Displayed on M-MDS but does not function.
WIN_TEM (1) °C,°F
NOTE: Displayed on M-MDS but does not function.
WIN_TEM_A (1) OK/NG
NOTE: Displayed on M-MDS but does not function.
WIP_CS_RLS Off/Single_Wipe/SPEED_LOW/SPEED_HI/Failure Conversion Displays the auto wiper control request signal reception status. The BCM receives an auto wiper control request signal via LIN communication from the autolight sensor/rain sensor.
  • Off: Off signal is received
  • Single_Wipe: Intermittent operation signal is received
  • SPEED_LOW: Continuous low operation signal is received
  • SPEED_HI: High speed signal is received
  • Failure: Auto wiper control request signal cannot be received
 3X
WIP_F_AS P_Posi/Not_P_Posi Conversion Displays the auto stop switch operation status (wiper arm and blade position).
  • P_Posi: Wipers are stopped in park position
  • Not_P_Posi: Wipers are stopped in position other than park
 3M
WIP_F_INT_L % Conversion Displays the sensitivity adjustment volume operation status. The BCM receives a sensitivity adjustment volume input signal via CAN communication from the start stop unit. The value changes according to the sensitivity adjustment volume operation. 2C/2D
WIP_F_RY Off/On Output Displays the wiper INT relay operation status.
  • Off: Wiper INT relay is off (wiper are not operating)
  • On: Wiper INT relay is on (wipers are operating)
 3F
WIP_F_RY_HI Off/On Output Displays the wiper HI relay operation status.
NOTE:
  • If the wiper switch is in the INT/AUTO position, the wiper HI relay turns on depending on the amount of rainfall.
  • Off: Wiper HI relay is off (wiper switch is in position other than HI)
  • On: Wiper HI relay is on (wiper switch is in HI position)
 3G
WIP_F_SW OFF/LOW/HI/INT/AUTO Conversion Displays the wiper switch operation status. The BCM receives a wiper switch input signal via CAN communication from the start stop unit.
  • Off: Wiper switch off signal is received (wiper switch is in OFF position)
  • LOW: Wiper switch LOW signal is received (wiper switch is in LO position)
  • HI: Wiper switch HI signal is received (wiper switch is in HI position)
  • INT/AUTO: Wiper switch INT signal or AUTO signal is received (wiper switch is in INT/AUTO position)
 2C/2D
WIP_R_CTRL Off/INT/On/On_1Time/On_2Time/On_3Time/On_4Time
NOTE: Displayed on M-MDS but does not function.
WIP_R_INT s
NOTE: Displayed on M-MDS but does not function.
WIP_R_SW OFF/LOW/INT
NOTE: Displayed on M-MDS but does not function.
(1) 2017MY

(2) 2017MY, 2018MY

(3) With theft-deterrent system
About FixVault