Interwheel differential lock, function - GF28.60-P-3200GZ
MODEL 164.1 with CODE (430) Offroad package
MODEL 164.8 with CODE (430) Offroad package
The driver can use a differential lock selector wheel (N72s34), which is located in the lower control panel (N72), to choose between three different settings for the differential. The following differential settings are available in the "High" on-road ratio:
- Setting 1: The transfer case differential (interaxle differential lock) is automatically locked
- Setting 2: The transfer case differential (interaxle differential lock) is manually locked (100 %)
- Setting 3: The transfer case differential (interaxle differential lock) and the rear axle differential (interwheel differential lock) are manually locked (100 %)
The following differential settings are available in the "Low" offroad ratio:
- Setting 1: The transfer case differential (interaxle differential lock) is automatically locked
- Setting 2: The transfer case differential (interaxle differential lock) is manually locked (100 %) and the rear axle differential (interwheel differential lock) is automatically locked
- Setting 3: The transfer case differential (interaxle differential lock) and the rear axle differential (interwheel differential lock) are manually locked (100 %)
Each differential setting has a red LED to indicate the active state.
Specified locking torque
When the lock is actuated, the transfer case control unit (N15/7) calculates a specified locking torque according to the current operating state.
The information about the specified locking torque is sent by the transfer case control unit via the CAN data bus to the rear axle differential lock control unit (N15/9). This pre-control of the locking torque has the following advantages:
- Ensuring traction for moving off
- Avoiding over-braking of the rear axle during manual downshifts
- Reducing the load change shock
- Avoiding over-steer or under-steer under load
To allow calculation of the specified locking torque, the transfer case control unit requires the following information:
- Cornering recognition
- Tire tolerances
- Wheel speeds
- Vehicle speed
- Engine torque
- Accelerator pedal position
Lock control
The rear axle differential lock control unit regulates the distribution of the engine torque between the left and right rear wheels. The multidisk clutch (interwheel differential lock) is actuated via the rear axle differential actuator motor.
When the rear axle differential actuator motor is actuated by the rear axle differential lock control unit, the rear axle differential actuator motor turns the cam with ball ramp mechanism (3) via the spur gear. Due to the ball ramp mechanism installed on the cam, the balls run up to their "ramps" when the cam is turned. This produces an axial movement of the cam. The cam pushes the thrust ring (6) against the interwheel differential lock disk pack (5). This produces a defined friction torque in the disk pack. The differential housing (4) and the differential side gear (2) are mutually locked.
In order to optimize fuel consumption, the position of the spur gear is maintained by the magnetic brake (7) in the rear axle differential actuator motor if the differential is permanently locked.
Safety concept
In the deenergized state (power failure) the interwheel differential lock is open.
Lock actuation on ABS/ESP control
The transfer case control unit must respond to the particular requirements of the ABS and ESP systems in order to avoid negative influences on directional stability and road adhesion. These requirements are made available to the rear axle differential lock control unit via the CAN data bus. For this purpose the transfer case control unit is capable of opening the interwheel differential lock. To guarantee this function, the following information is required:
- Deceleration at the rear axle
- Vehicle speed
- Signal ABS "active"
- ESP requirement
- Stop light signal
Lock overload protection
The aim of the lock overload protection is to protect the interwheel differential lock against damage and guarantee the maximum possible availability of the lock function.
After ignition "OFF/ON", the 1st setting of the differential lock is automatically active for >10 s; below 10 s the currently selected differential setting remains active.
| Transfer case control unit, component description | N15/7 | GF28.19-P-3200GZ |
| Rear axle differential lock control unit, component description | N15/9 | GF28.19-P-3500GZ |
| Rear axle differential actuator motor, component description | M70 | GF28.19-P-3501GZ |
| Differential, component description | GF28.50-P-1000GZ | |
| Multidisk clutch, component description | GF28.50-P-1100GZ |