Self-adjustment of mixture formation, function - GF07.10-P-1029V

ENGINES 272.920 in MODEL 203 up to model year 2008 /AEJ 07

ENGINES 272.922 in MODEL 211

ENGINES 272.940 in MODEL 203 up to model year 2008 /AEJ 07

ENGINES 272.941 in MODEL 203 up to model year 2008 /AEJ 07

ENGINES 272.942 in MODEL 171 up to model year 2008 /AEJ 07

ENGINES 272.943 in MODEL 211, 219

ENGINES 272.944 in MODEL 211

ENGINES 272.945 in MODEL 251 up to model year 2008 /AEJ 07

ENGINES 272.946 in MODEL 221 up to model year 2008 /AEJ 07

ENGINES 272.960 in MODEL 203 up to model year 2008 /AEJ 07

ENGINES 272.963 in MODEL 171 up to model year 2008 /AEJ 07

ENGINES 272.964 in MODEL 211, 219

ENGINES 272.965 in MODEL 221 up to model year 2008 /AEJ 07

ENGINES 272.966 in MODEL 230 up to model year 2008 /AEJ 07

ENGINES 272.967 in MODEL 164, 251 up to model year 2008 /AEJ 07

ENGINES 272.970 in MODEL 203 up to model year 2008 /AEJ 07

ENGINES 272.972 in MODEL 211

ENGINES 272.975 in MODEL 221 up to model year 2008 /AEJ 07

ENGINES 273.922 in MODEL 221 up to model year 2008 /AEJ 07

ENGINES 273.923 in MODEL 164 up to model year 2008 /AEJ 07

ENGINES 273.924 in MODEL 221 up to model year 2008 /AEJ 07

ENGINES 273.960 in MODEL 211, 219

ENGINES 273.961 in MODEL 216, 221 up to model year 2008 /AEJ 07

ENGINES 273.962 in MODEL 211

ENGINES 273.963 in MODEL 164, 251 up to model year 2008 /AEJ 07

ENGINES 273.965 in MODEL 230 up to model year 2008 /AEJ 07

ENGINES 273.967 in MODEL 209

ENGINES 273.968 in MODEL 221 up to model year 2008 /AEJ 07

ENGINES 272.940 in MODEL 209

ENGINES 272.960 in MODEL 209

Fig 1: Shifting Of Lambda Performance Map (Lambda Control Factor Prior To Self-Adjustment)

Courtesy of MERCEDES-BENZ USA

On vehicles fitted with a closed-loop controlled catalytic converter, the lambda control determines the injection time so exactly that a certain fuel-air ratio (λ) is maintained in all operating states.

If faults occur, the ME-SFI [ME] control unit automatically makes a correction in the mixture formation. Here the lambda performance map is shifted within certain limits in such a way that the lambda control is not at the upper or lower regulation limit (d).

The following faults require a mixture adjustment:

Wear or carbon deposits on fuel injection valves
Fault on mass air flow sensor
Incorrect injection pressure (e.g. through blocked fuel filter)
Defective purge control valve
Engine wear (e.g. leaky valves)

If the mixture composition constantly drifts out of the middle control range (e.g. 0 ± 10%) the ME-SFI [ME] control unit under certain operating conditions shifts the lambda map sufficiently far until a lambda control factor of approx. 0% (g) is again achieved.

Self-adjustment ensures that the mixture composition in the control mode (e.g. warming-up phase) is neither too rich nor too lean. This also prevents the lambda control from moving up to the control limit at high altitudes.

Example:

As the result of a lean fuel/air mixture the readout of the lambda control factor changes to 18% (e). Under certain operating conditions the lambda performance map is shifted (arrow) by the ME-SFI [ME] control unit.

This shifting of the lambda performance map is the self-adjustment of the mixture formation process to the existing air/fuel mixture. After this self-adjustment the lambda control factor is again in the central control range (g).

This self-adjustment of the mixture formation can be carried out in the following operating states:

Idle speed
Lower part load
Upper partial load.

The following actual values can be read out using STAR DIAGNOSIS

Lambda map shift active
Direction of the shift (tendency towards rich or lean)
Extent of the shift

Representation of self-adjustment values with STAR DIAGNOSIS in idle

The representation in milliseconds means that the value displayed is added to, or subtracted from, the air mass inducted by the engine in order to determine the injection time.

The maximum correction value is ±1 ms.

Example:

Calculated injection time (performance map): 3.0 ms

Displayed correction value: +0, 3 ms

For determining the injection time (fuel injection quantity) the ME-SFI [ME] control unit uses a calculated value of 3.3 ms (3.0 ms+0.3 ms).

Representation of self-adjustment values with STAR DIAGNOSIS for partial load

The representation of the factor means that the indicated value for determining the injection time is multiplied by the air mass inducted by the engine.

The correction factor lies between 0.68 and 1.32.

Example:

Calculated air mass: 150 kg/hour

Displayed correction value: 1, 10

A calculated air mass value of the of 165 kg/h is used by the engine control unit to determine the injection time (fuel injection quantity).

Component description for ME-SFI [ME] control unit		GF07.61-P-6000V
Component description for O ₂ sensors	O₂ sensors upstream of catalytic converter	GF07.04-P-6100V
Component description for O ₂ sensors	O₂ sensors downstream of catalytic converter	GF07.04-P-6100VA