Manual Trans: Overhaul
- General Information
- Specifications
- Special Tools
- Transaxle
- Disassembly And Reassembly
- Disassembly Service Points
- >A< Sealing Cap Removal
- >B< Transaxle Case Removal
- >C< Reverse Idler Gear Shaft Removal
- >D< 3RD-4TH Speed Shift Rail/3RD-4TH Speed Shift Fork/5TH Speed Shift Fork/Snap Ring/Reverse Shift Lug/5TH Speed Shift Rail/Steel Ball/Reverse Interlock Rail Removal
- >E< 3RD-4TH Speed Shift Rail/3RD-4TH Speed Shift Fork/5TH Speed-Reverse Shift Rail/5TH Speed-Reverse Shift Fork Removal
- >F< Input Shaft/Output Shaft Removal
- Adjustment Before Reassembly Spacer Selection For Differential Case End Play Adjustment < F5M41 >
- Spacer Selection For Differential Case Preload Adjustment < F5M42 >
- Reassembly Service Points
- >A< Output Shaft/Input Shaft Installation
- >B< Output Shaft/Input Shaft Installation
- >C< Front Bearing Retainer Installation
- >D< Reverse Interlock Rail/Steel Ball/5TH Speed Shift Rail/Reverse Shift Lug/Snap Ring/5TH Speed Shift Fork/3RD-4TH Speed Shift Fork/3RD-4TH Speed Shift Rail Installation
- >E< 5TH Speed-Reverse Shift Fork/5TH Speed-Reverse Shift Rail/3RD-4TH Speed Shift Fork/3RD-4TH Speed Shift Rail Installation
- >F< Spring Pin Installation
- >G< Spacer Installation
- >H< Oil Guide Installation
- >I< Reverse Idler Gear Shaft Installation
- >J< Outer Race Installation
- >K< Transaxle Case Installation
- >L< Sealing Cap Installation
- >M< Reverse Idler Gear Shaft Bolt Installation
- >N< Under Cover Installation
- >O< Control Housing Installation
- >P< Speedometer Gear Installation
- >Q< Select Lever Installation
- Inspection
- Input Shaft
- Disassembly And Reassembly
- Disassembly Service Points
- Reassembly Service Points
- >A< Oil Seal Installation
- >B< Ball Bearing Installation
- >C< Snap Ring Installation
- >D< Synchronizer Spring Installation
- >E< 3RD-4TH Speed Synchronizer Hub Installation
- >F< Synchronizer Sleeve Installation
- >G< 4TH Speed Gear Sleeve Installation
- >H< 5TH Speed Gear Sleeve Installation
- >I< 5TH Speed Gear Installation
- >J< 5TH Speed-Reverse Synchronizer Hub Installation
- >K< Synchronizer Sleeve Installation
- >L< Thrust Plate Installation
- >M< Reverse Brake Sleeve Installation
- >N< Thrust Plate Stopper Installation
- >O< Ball Bearing Installation
- >P< Snap Ring Installation
- Inspection
- Output Shaft
- Disassembly And Reassembly
- Disassembly Service Points
- Reassembly Service Points
- >A< Roller Bearing Inner Race Installation
- >B< Snap Ring Installation
- >C< 1ST Speed Gear Sleeve Installation
- >D< Synchronizer Spring Installation
- >E< 1ST-2ND Speed Synchronizer Hub Installation
- >F< Synchronizer Sleeve Installation
- >G< Synchronizer Spring Installation
- >H< 2ND Speed Gear Sleeve Installation
- >I< 3RD Speed Gear Installation
- >J< Snap Ring Installation
- >K< 4TH Speed Gear Installation
- >L< 5TH Speed Gear Sleeve Installation
- >M< 5TH Speed-Reverse Synchronizer Hub Installation
- >N< Reverse Gear/Needle Roller Bearing/Reverse Gear Bearing Sleeve Installation
- >0< Ball Bearing Installation
- >P< Snap Ring Installation
- Inspection
- Reverse Idler Gear < F5M42 >
- Speedometer Gear
- Select Lever
- Control Housing
- Clutch Housing
- Transaxle Case
- Differential