FixVault
Home › Mitsubishi › 2006 › Lancer Evolution › Repair and Diagnosis › Transmission › Manual Trans › Manual Transmission On-Vehicle Service - Lancer Evolution › Special Tools

Special Tools

SPECIAL TOOLS SPECIFICATION

TOOL TOOL NUMBER AND NAME SUPERSESSION APPLICATION
A
G04296601G04296602G04296603G04296604G04296605G04296606G04296607

B
G04296601G04296602G04296603G04296604G04296605G04296606G04296607

C
G04296601G04296602G04296603G04296604G04296605G04296606G04296607

D
G04296601G04296602G04296603G04296604G04296605G04296606G04296607

E
G04296601G04296602G04296603G04296604G04296605G04296606G04296607

F
G04296601G04296602G04296603G04296604G04296605G04296606G04296607

G
G04296601G04296602G04296603G04296604G04296605G04296606G04296607
 MB991958
  1. MB991824
  2. MB991827
  3. MB991910
  4. MB991911
  5. MB991914
  6. MB991825
  7. MB991826

M.U.T.-III sub assembly
  1. Vehicle communication interface (V.C.I.)
  2. M.U.T.-III USB cable
  3. M.U.T.-III main harness A (Vehicles with CAN communication system)
  4. M.U.T.-III main harness B (Vehicles without CAN communication system)
  5. M.U.T.-III main harness C (for Daimler Chrysler models only)
  6. M.U.T.-III measurement adapter
  7. M.U.T.-III trigger harness
 MB991824-KIT
NOTE: G: MB991826 M.U.T.-III Trigger Harness is not necessary when pushing V.C.I. ENTER key.
 Checking diagnostic trouble codes
CAUTION: If you connect M.U.T.-III main harness A to a vehicle without CAN communication system to use the M.U.T.-III, a pulse signal may interfere with the simulated vehicle speed lines, thus causing the M.U.T.-III inoperative.
Therefore, use the M.U.T.-III main harness B (MB991911) instead.
G04296608
 MB991529
Diagnostic trouble code check harness.		 Tool not necessary if scan tool (M.U.T.-III) is available. For checking of ACD
G04296609
 MB991348
Test harness set		 MB991348-01 Inspection using an oscilloscope
G04296610
 MB992006 Extra fine probe Continuity check and voltage measurement at harness wire or connector
G04296611
 MD998330 (Includes MD998331)
Oil pressure gauge (3.0 MPa, 427 psi)		 MD998330-01 Measurement of hydraulic pressure
G04296612
 MB991705
Adapter		 - Connection for oil pressure gauge
G04296613
 MB991453
Engine hanger assembly		 MZ203827-01 When the engine hanger is used: Supporting the engine assembly during removal and installation of the transaxle assembly
NOTE: Special tool MB991454 is a part of engine hanger attachment set MB991453.
G04296614
 GENERAL SERVICE TOOL MZ203827
Engine lifter		 MZ203827-01
G04296615
 MB991454
Engine hanger balancer		 MZ203827-01
G04296616
 MB991895
Engine hanger		 -
G04296617
 MB991928
Engine hanger
  1. MB991929

    Joint (50) x 2

  2. MB991930

    Joint (90) x 2

  3. MB991931

    Joint (140) x 2

  4. MB991932

    Foot (standard) x 4

  5. MB991933

    Foot (short) x 2

  6. MB991934

    Chain and hook assembly

 -
About FixVault