FixVault
Home › Nissan-Datsun › 2002 › Sentra SE-R, Standard › Repair and Diagnosis › External Pages › Different car › Section 1948 (Engine Immobilizer) › Engine Immobiliser System › Data List / Active Test

Data List / Active Test

WARNING: This page is about a different car, the 2006 Scion tC. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ DATA LIST 

    HINT:

    Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.

    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch ON.
    3. Read the DATA LIST by following the directions on the tester screen.

    Transponder key ECU assembly: 

    TRANSPONDER KEY ECU ASSEMBLY DATA LIST

    Item Measurement Item/ Display (Range) Normal Condition Diagnostic Note
    KEY SW Unlock warning switch signal / ON or OFF OFF: No key is in ignition key cylinder
    ON: Key is in ignition key cylinder    		 -
    IG SW Ignition switch signal / ON or OFF OFF: Ignition switch OFF or ACC
    ON: Ignition switch ON    		 -
    IMMOBILIZER Immobilizer system status / SET or UNSET UNSET: Ignition switch ON
    SET: No key is in ignition key cylinder    		 -
    PERMIT (START) Engine starting control / OK or NG OK: Engine starting is permitted
    NG: Engine starting is not permitted    		 -
    RESPONSE Transponder chip data / NG or OK NG: Data error
    OK: Data OK    		 -
    FRAME Transponder chip data / NG or OK NG: Data error
    OK: Data OK    		 -
    SERIAL NUMBER Transponder chip data / NG or OK NG: Data error
    OK: Data OK    		 -
    ENCRYPT CODE Transponder chip data / NG or OK NG: Data error
    OK: Data OK    		 -
    STATUS Transponder chip data / NG or OK NG: Data error
    OK: Data OK    		 -
    BCC Transponder chip signal / NG or OK NG: Incorrect data sent
    OK: Correct data sent    		 -
    SUB KEY Sub-key code signal / NO MATCH or MATCH NOMATCH: Unmatched sub-key code is sent
    MATCH: Registered sub-key code is sent    		 -
    MASTER KEY Master key code signal / NOMATCH or MATCH NOMATCH: Unmatched master key code is sent
    MATCH: Registered master key code is sent    		 -
    REGIST SUB CODE Number of registered sub-keys / min.: 0, max.: 3 Number of registered sub-keys -
    REGIST MAS CODE Number of registered master keys / min.: 0, max.: 5 Number of registered master keys -
    REG CODE SPACE Memory space for key code registration / NOT FUL or FULL NOT FUL: Possible to register more key codes
    FULL: Cannot register any more key codes    		 -
    +B +B judgment / NORMAL or BREAK NORMAL: Battery supply is normal
    BREAK: Battery supply is malfunctioning    		 -
    ANTENNA CIOL Transponder key coil condition / NORMAL or FAIL NORMAL: Transponder key coil is normal
    FAIL: Transponder key coil is malfunctioning    		 -
  2. PERFORM ACTIVE TEST 

    HINT:

    Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time.

    The DATA LIST can be displayed during the ACTIVE TEST.

    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch ON.
    3. Perform the ACTIVE TEST by following the directions on the tester screen.

    Transponder key ECU assembly: 

    TRANSPONDER KEY ECU ASSEMBLY ACTIVE TEST

    Item Test Details Diagnostic Note
    SECURITY INDIC Turn security indicator light ON/OFF -
About FixVault