Standards By Consult-II
WARNING: This page is about a different car, the 2006 Infiniti G35. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:
Items displayed are data calculated by control unit and may indicate normal operation even if output circuit (harness) is open or shorted.
MONITOR ITEM REFERENCE
| Monitor item | Contents | DATA MONITOR | Check item | |||||
|---|---|---|---|---|---|---|---|---|
| Condition | Reference value in normal operation | |||||||
| SLCT LVR POSI | Shift position determined by the A/T PNP switch signal | Indicate each shift position (M/T models normally remain at ##) | "When "SHIFT POSITION ERROR" Appears in Self-Diagnostic Results Display (A/T Models) " | |||||
| GEAR | Gear position determined by TCM | 1:1st gear (M/T models: normally remain at 1) 2:2nd gear 3:3rd gear 4:4th gear 5:5th gear |
- | |||||
| FR LH SENSOR FR RH SENSOR RR LH SENSOR RR RH SENSOR |
Wheel speed | Vehicle stopped | 0 [km/h] | "WHEEL SENSOR SYSTEM " | ||||
| Vehicle running (Note (1)) | Almost in accordance with speedometer display (within +/-10 %) | |||||||
| ACCEL POS SIG | Throttle actuator opening/closing is displayed (linked with accelerator pedal). | Accelerator pedal not depressed (ignition switch is ON) | 0 % | Communication circuit between VDC/TCS/ABS control unit and ECM | ||||
| Depress accelerator pedal (ignition switch is ON) | 0 - 100 % | |||||||
| ENGINE RPM | With engine running | With engine stopped | 0 RPM | Engine speed signal circuit | ||||
| Engine running | Almost in accordance with tachometer display | |||||||
| STR ANGLE SIG | Steering angle detected by steering angle sensor | Straight-ahead | Approx. 0° | "STEERING ANGLE SENSOR SYSTEM " | ||||
| Steering wheel turned | -720 to 720° | |||||||
| YAW RATE SEN | Yaw rate detected by yaw rate sensor | Vehicle stopped | Approx. 0 d/s | "YAW RATE/SIDE G SENSOR SYSTEM " | ||||
| Vehicle running | -70 to 70 d/s | |||||||
| SIDE G SENSOR | Transverse G detected by side G sensor | Vehicle stopped | Approx. 0 m/s2 | |||||
| Vehicle running | -24.3 to 24.1 m/s2 | |||||||
| PRESS SENSOR | Brake fluid pressure detected by pressure sensor | With ignition switch turned ON and brake pedal released | Approx. 0 bar | "PRESSURE SENSOR SYSTEM " | ||||
| With ignition switch turned ON and brake pedal depressed | -40 to 300 bar | |||||||
| BATTERY VOLT | Battery voltage supplied to VDC/TCS/ABS control unit | Ignition switch ON | 10 - 16 V | "VDC/TCS/ABS CONTROL UNIT POWER AND GROUND SYSTEM " | ||||
| STOP LAMP SW | Brake pedal operation | Brake pedal depressed | ON | "STOP LAMP SWITCH SYSTEM " | ||||
| Brake pedal not depressed | OFF | |||||||
| PARK BRAKE SW | Parking brake condition | Parking brake operated | ON | Parking brake switch circuit | ||||
| Parking brake not operated | OFF | |||||||
| OFF SW | VDC OFF switch ON/OFF condition | VDC OFF switch ON (When VDC OFF indicator lamp is ON) | ON | "VDC OFF SWITCH " | ||||
| VDC OFF switch OFF (When VDC OFF indicator lamp is OFF) | OFF | |||||||
| ABS WARN LAMP | ABS warning lamp ON condition (Note (2)) | ABS warning lamp ON | ON | ABS warning lamp harness | ||||
| ABS warning lamp OFF | OFF | |||||||
| MOTOR RELAY | Operation condition of motor and motor relay | When motor relay and motor are operating | ON | "ACTUATOR MOTOR AND MOTOR RELAY SYSTEM " | ||||
| When motor relay and motor are not operating | OFF | |||||||
| ACTUATOR RLY | Solenoid valve relay operation condition | When solenoid valve relay is operating | ON | "ACTUATOR RELAY SYSTEM " | ||||
| When solenoid valve relay is not operating | OFF | |||||||
| OFF LAMP | VDC OFF indicator lamp condition (Note (2)) | When VDC OFF indicator lamp is ON | ON | VDC OFF indicator lamp circuit | ||||
| When VDC OFF indicator lamp is OFF | OFF | |||||||
| SLIP LAMP | SLIP indicator lamp condition (Note (2)) | When SLIP indicator lamp is ON | ON | SLIP indicator lamp circuit | ||||
| When SLIP indicator lamp is OFF | OFF | |||||||
| IN ABS S/V OUT ABS S/V | Solenoid valve operation | Actuator (solenoid) is active ("ACTIVE TEST" with CONSULT-II) or solenoid valve relay is inactive (in fail-safe mode). | ON | "SOLENOID AND VDC CHANGE-OVER VALVE SYSTEM " | ||||
| When actuator (solenoid) is not active and solenoid valve relay is active (ignition switch ON). | OFF | |||||||
| USV HSV | VDC switch-over valve condition | When actuator (switch-over valve) is active ("ACTIVE TEST" with CONSULT-II) or actuator relay is inactive (when in fail-safe mode). | ON | |||||
| When actuator (switch-over valve) is not active and actuator relay is active (ignition switch ON). | OFF | |||||||
| V/R OUTPUT | Actuator relay activated (ON/OFF) | When actuator relay is active (engine is running). | ON | "ACTUATOR RELAY SYSTEM " | ||||
| When actuator relay is not active (before engine starts and in fail-safe mode). | OFF | |||||||
| M/R OUTPUT | Actuator motor and motor relay condition (ON/OFF) | When actuator motor and motor relay are active ("ACTIVE TEST" with CONSULT-II). | ON | "ACTUATOR MOTOR AND MOTOR RELAY SYSTEM " | ||||
| When the actuator motor and motor relay are not operating | OFF | |||||||
| FLUID LEV SW | ON/OFF condition of brake fluid level switch | When brake fluid level switch ON | ON | "BRAKE FLUID LEVEL SWITCH SYSTEM " | ||||
| When brake fluid level switch OFF | OFF | |||||||
| FAIL SIGNAL | Fail signal condition | VDC fail TCS fail ABS fail EBD fail |
OFF | VDC system TCS system ABS system EBD system |
||||
|
||||||||