FixVault
Home › Nissan-Datsun › 2004 › Sentra SE-R › Repair and Diagnosis › External Pages › Different car › Section 2048 (Seats) › Automatic Drive Positioner › Door Mirror Remote Control Switch (Changeover Switch) Circuit Check

Door Mirror Remote Control Switch (Changeover Switch) Circuit Check

WARNING: This page is about a different car, the 2007 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FUNCTION 

    With CONSULT-II 

    Check the operation on "MIR CHNG SW-R" or "MIR CHNG SW-L" in the DATA MONITOR.

    DATA MONITOR REFERENCE

    Monitor item [OPERATION or UNIT] Contents
    MIR CHNG SW-R "ON/OFF" ON/OFF status judged from the door mirror remote control switch (switching to RIGHT) signal is displayed.
    MIR CHNG SW-L "ON/OFF" ON/OFF status judged from the door mirror remote control switch (switching to LEFT) signal is displayed.
    Fig 1: CONSULT II Display - DATA MONITOR
    G04903045Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch to ACC.
    2. Check voltage between automatic drive positioner control unit connector and ground.
      TERMINALS VOLTAGE CHART

      Connector Terminals Condition Voltage (V) (Approx.)
      (+) (-)
      M41 2 Ground Changeover switch RIGHT position 0
      Other than above 5
      18 Changeover switch LEFT position 0
      Other than above 5
      Fig 2: Checking Voltage Between Automatic Drive Positioner Control Unit Connector Terminal 2, 18 And Ground
      G04903046Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Door mirror remote control switch (changeover switch) is OK.

    NG: GO TO 2.

  2. CHECK DOOR MIRROR REMOTE CONTROL SWITCH CIRCUIT HARNESS CONTINUITY 
    1. Turn ignition switch OFF.
    2. Disconnect automatic drive positioner control unit and door mirror remote control switch.
    3. Check continuity between automatic drive positioner control unit connector M41 (A) terminals 2, 18 and door mirror remote control switch connector D10 (B) terminals 5, 6.

      2 - 5 : Continuity should exist. 

      18 - 6 : Continuity should exist. 

    4. Check continuity between automatic drive positioner control unit connector M41 (A) terminals 2, 18 and ground.

      2 - Ground : Continuity should not exist. 

      18 - Ground : Continuity should not exist. 

    OK or NG 

    OK: GO TO 3.

    NG: Repair or replace harness.

    Fig 3: Checking Continuity Between Automatic Drive Positioner Control Unit Connector (A) M41 Terminals 2, 18 And Door Mirror Remote Control Switch Connector D10 (B) Terminals 5, 6, And Between Connector (A) M41 Terminals 2, 18 and ground
    G04907765Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK DOOR MIRROR REMOTE CONTROL SWITCH (CHANGEOVER SWITCH) 

    Check continuity between door mirror remote control switch terminals as follows.

    TERMINALS CONTINUITY CHART

    Terminals Condition Continuity
    5 7 Changeover switch
    RIGHT position    		 Yes
    Other than above No
    6 Changeover switch LEFT position Yes
    Other than above No

    OK or NG 

    OK: Check the condition of the harness and the connector.

    NG: Replace door mirror remote control switch.

    Fig 4: Checking Continuity Between Door Mirror Remote Control Switch Terminal 7 And Terminals 5 & 6
    G04907766Courtesy of NISSAN MOTOR CO., U.S.A.
About FixVault