FixVault
Home › Nissan-Datsun › 2004 › Sentra SE-R › Repair and Diagnosis › External Pages › Different car › Section 2084 (Glass, Window System & Mirrors) › Power Window System › Limit Switch Circuit Inspection Front RH

Limit Switch Circuit Inspection Front RH

WARNING: This page is about a different car, the 2008 Nissan Maxima. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FRONT POWER WINDOW MOTOR RH LIMIT SIGNAL 
    1. Turn ignition switch ON.
    2. Check voltage between front power window motor RH connector D104 terminal 4 and ground.
      FRONT POWER WINDOW MOTOR RH CONNECTOR D104 TERMINAL 4 AND GROUND

      Connector Terminals Condition Voltage (V) (Approx.)
      (+) (-)
      D104 4 Ground Front power window RH is between fully-open and just before fully-closed position (ON) 0
      Front power window RH is between just before fully-closed position and fully-closed position (OFF) 5
      Fig 1: Checking Voltage Between Front Power Window Motor RH Connector D104 Terminal 4 And Ground
      G04917097Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Limit switch circuit is OK.

    NG: GO TO 2.

  2. CHECK LIMIT SWITCH GROUND CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect front power window motor RH.
    3. Check continuity between front power window motor RH connector D104 terminal 3 and ground.

      3 - Ground: Continuity should exist. 

    Fig 2: Checking Continuity Between Front Power Window Motor LH Connector D9 Terminal 3 And Ground
    G04917098Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO  4.

    NG: GO TO 3.

  3. CHECK HARNESS CONTINUITY 
    1. Disconnect power window and door lock/unlock switch RH.
    2. Check continuity between front power window motor RH connector D104 terminal 3 and power window and door lock/unlock switch RH connector D105 terminal 3.

      3 - 3: Continuity should exist. 

    Fig 3: Checking Harness Continuity
    G04917105Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Replace power window and door lock/unlock switch RH. Refer to "FRONT DOOR ".

    NG: Repair or replace harness.

  4. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH OUTPUT SIGNAL 
    1. Turn ignition switch ON.
    2. Check voltage between power window and door lock/unlock switch RH connector D105 terminal 15 and ground.

      15 - Ground: Approx. 5V 

    Fig 4: Checking Voltage Between Power Window And Door Lock/Unlock Switch RH Connector D105 Terminal 15 And Ground
    G04902754Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 5.

    NG: Replace power window and door lock/unlock switch RH. Refer to "FRONT DOOR ".

  5. CHECK HARNESS CONTINUITY 
    1. Turn ignition switch OFF.
    2. Disconnect power window and door lock/unlock switch RH.
    3. Check continuity between power window and door lock/unlock switch RH connector D105 terminal 15 and front power window motor RH connector D104 terminal 4.

      15 - 4: Continuity should exist. 

    Fig 5: Checking Harness Continuity
    G04917107Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: GO TO 6.

    NG: Repair or replace harness.

  6. CHECK LIMIT SWITCH 
    1. Connect front power window motor RH and power window and door lock/unlock switch RH connector.
    2. Turn ignition switch ON.
    3. Check continuity between front power window motor RH connector D104 terminals 3 and 4.
      FRONT POWER WINDOW MOTOR RH CONNECTOR D104 TERMINALS 3 AND 4

      Connector Terminals Condition Continuity
      D104 4 3 Front power window RH is between fully-open and just before fully-closed position (ON) Yes
      Front power window RH is between just before fully-closed position and fully-closed position (OFF) No
      Fig 6: Checking Continuity Between Front Power Window Motor RH Connector D104 Terminal 3 And 4
      G04917102Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK: Repair or replace harness.

    NG: Replace front power window motor RH. Refer to "FRONT DOOR GLASS AND REGULATOR ".

About FixVault