Control Valve Assembly: Assembly

Install upper, inter and lower body.
1. Place oil circuit of upper body face up. Install steel balls in their proper positions.
  
  Fig 1: Identifying Steel Balls
  Courtesy of NISSAN MOTOR CO., U.S.A.
2. Install reamer bolts f from bottom of upper body. Using reamer bolts as guides, install new separating plate as a set.
  CAUTION: Do not reuse separating plate.
  
  Fig 2: Identifying Reamer Bolts
  Courtesy of NISSAN MOTOR CO., U.S.A.
3. Install pilot filter.
  
  Fig 3: Identifying Pilot Filter
  Courtesy of NISSAN MOTOR CO., U.S.A.
4. Place lower body as shown (side of inter body face up). Install steel balls in their proper positions.
  
  Fig 4: Identifying Steel Balls
  Courtesy of NISSAN MOTOR CO., U.S.A.
5. Install inter body on upper body using reamer bolts f as guides.
  CAUTION: Be careful not to dislocate or drop steel balls.
  
  Fig 5: Identifying Inter Body
  Courtesy of NISSAN MOTOR CO., U.S.A.
6. Install check balls and oil cooler relief valve springs in their proper positions in lower body.
  
  Fig 6: Identifying Check Balls And Oil Cooler Relief Valve Springs
  Courtesy of NISSAN MOTOR CO., U.S.A.
7. Install bolts e from bottom of lower body. Using bolts e as guides, install new separating plate as a set.
  CAUTION: Do not reuse separating plate.
8. Temporarily install support plates on lower body.
  
  Fig 7: Identifying Bolts
  Courtesy of NISSAN MOTOR CO., U.S.A.
9. Install lower body on inter body using reamer bolts f as guides and tighten reamer bolts f slightly.
  
  Fig 8: Identifying Lower Body
  Courtesy of NISSAN MOTOR CO., U.S.A.
Install new O-rings to solenoid valves and terminal body.
CAUTION:
- Do not reuse O-rings.
- Apply ATF to O-rings.
  
  Fig 9: Identifying O-Rings
  Courtesy of NISSAN MOTOR CO., U.S.A.

Install and tighten bolts.

Bolt length, number and location:

BOLT SPECIFICATIONS

Bolt symbol	a	b	c	d	e	f	g
Bolt length "l" mm (in) Courtesy of NISSAN MOTOR CO., U.S.A.	13.5 (0.531)	58.0 (2.283)	40.0 (1.575)	66.0 (2.598)	33.0 (1.299)	78.0 (3.071)	18.0 (0.709)
Number of bolts	6	3	6	11	2	2	1

Fig 10: Tightening Bolts In Sequence

Courtesy of NISSAN MOTOR CO., U.S.A.

Install and tighten bolts b to specified torque.
Specified torque: Refer to " COMPONENTS ".

Fig 11: Tightening Bolts
Courtesy of NISSAN MOTOR CO., U.S.A.
Install solenoid valve assembly and line pressure solenoid valve to lower body.

Fig 12: Identifying Solenoid Valve Assembly
Courtesy of NISSAN MOTOR CO., U.S.A.
Set oil strainer, then tighten bolts a, d, f and nuts to specified torque.
Specified torque: Refer to " COMPONENTS ".

Fig 13: Tightening Bolts In Sequence
Courtesy of NISSAN MOTOR CO., U.S.A.
Tighten bolts e to specified torque.
Specified torque: Refer to " COMPONENTS ".

Fig 14: Tightening Bolts
Courtesy of NISSAN MOTOR CO., U.S.A.