Front Power Window RH Circuit Check (Power Window and Door Lock/Unlock Switch RH Operation)

1. Turn ignition switch OFF.
2. Disconnect front power window motor RH.
3. Turn ignition switch ON.
4. Check voltage between front power window motor RH connector and ground.
   CONNECTOR TERMINAL VOLTAGE SPECIFICATION
   
   

   Connector	Terminals		Condition	Voltage (V) (Approx.)
   	(+)	(-)
   D104	1	Ground	UP	Battery voltage
   			DOWN	0
   	2		UP	0
   			DOWN	Battery voltage

   Fig 1: Checking Voltage Between Front Power Window Motor RH Connector And Ground

   

OK or NG 

OK: Replace front power window motor RH. Refer to "REGULATOR ASSEMBLY ".

NG: GO TO 2.

1. Turn ignition switch ON.
2. Check voltage between power window and door lock/unlock switch RH connector and ground.

   8 - Ground : Battery voltage 

OK or NG 

OK: GO TO  4.

NG: GO TO 3.

Fig 2: Checking Power Supply Circuit

1. Turn ignition switch OFF.
2. Disconnect BCM and power window and door lock/unlock switch RH.
3. Check continuity between BCM connector (A) and power window and door lock/unlock switch connector (B).
   CONNECTOR TERMINAL CONTINUITY SPECIFICATION
   
   

   A		B		Continuity
   Connector	Terminal	Connector	Terminal
   M20	68	D104	8	Yes

4. Check continuity between BCM connector (A) and ground.
   CONNECTOR TERMINAL CONTINUITY SPECIFICATION
   
   

   A		Ground	Continuity
   Connector	Terminal
   M20	68		No

   Fig 3: Checking Continuity Between BCM And Ground

   

OK or NG 

OK: Check the condition of the harness and the connector.

NG: Repair or replace harness.

1. Turn ignition switch ON.
2. Check voltage between power window and door lock/unlock switch RH connector and ground.
   CONNECTOR TERMINAL VOLTAGE SPECIFICATION
   
   

   Connector	Terminals		Condition	Voltage (V) (Approx.)
   	(+)	(-)
   D104	7	Ground	UP	Battery voltage
   			DOWN	0
   	6		UP	0
   			DOWN	Battery voltage

   Fig 4: Checking Voltage Between Power Window And Door Lock/Unlock Switch RH Connector D104 Terminals 6, 7 And Ground

   

OK or NG 

OK: GO TO 5.

NG: GO TO  6.

1. Turn ignition switch OFF.
2. Disconnect front power window motor RH and power window and door lock/unlock switch RH.
3. Check continuity between power window and door lock/unlock switch RH connector D104 (A) terminals 6, 7 and front power window motor RH connector D105 (B) terminals 1, 2.

   7 - 1 : Continuity should exist. 

   6 - 2 : Continuity should exist. 

4. Check continuity between power window and door lock/unlock switch RH connector D104 (A) terminals 6, 7 and ground.

   6 - Ground : Continuity should not exist. 

   7 - Ground : Continuity should not exist. 

   Fig 5: Checking Continuity Between Power Window And Door Lock/Unlock Switch RH Connector D104 Terminals 6, 7 And Ground

   

OK or NG 

OK: Replace front power window motor RH. Refer to "REGULATOR ASSEMBLY ".

NG: Repair or replace harness.

1. Turn ignition switch OFF.
2. Check continuity between power window and door lock/unlock switch RH terminals.
   CONNECTOR TERMINAL CONTINUITY SPECIFICATION
   
   

   Power window and door lock/unlock switch RH	Terminals		Condition	Continuity
   	6	8	DOWN	Yes
   			NEUTRAL or UP	No
   		11	NEUTRAL or UP	Yes
   			DOWN	No0
   	7	8	UP	Yes
   			NEUTRAL or DOWN	No
   		12	NEUTRAL or DOWN	Yes
   			UP	No

   Fig 6: Checking Continuity Between Power Window And Door Lock/Unlock Switch RH Terminals

   

OK or NG 

OK: GO TO 7.

NG: Replace power window and door lock/unlock switch RH. refer to "FRONT DOOR ".

Check continuity between power window and door lock/unlock switch connector and ground.

Fig 7: Checking Continuity Between Power Window And Door Lock/Unlock Switch Connector And Ground

OK or NG 

OK: Check the condition of the harness and the connector.

NG: GO TO 8.

1. Disconnect main power window and door lock/unlock switch and power window and door lock/unlock switch RH.
2. Check continuity between main power window and door lock/unlock switch connector (A) and power window and door lock/unlock switch RH connector (B).
   CONNECTOR TERMINAL CONTINUITY SPECIFICATION
   
   

   A		B		Continuity
   Connector	Terminal	Connector	Terminal
   D5	2	D104	11	Yes
   	3		12	Yes

3. Check continuity between main power window and door lock/unlock switch connector (A) and ground.
   CONNECTOR TERMINAL CONTINUITY SPECIFICATION
   
   

   A		Ground	Continuity
   Connector	Terminal
   D5	2		No
   	3		No

   Fig 8: Checking Ground Supply Circuit

   

OK or NG 

OK: GO TO 9.

NG: Repair or replace harness.

Check continuity between main power window and door lock/unlock switch terminals.

Fig 9: Checking Continuity Between Main Power Window And Door Lock/Unlock Switch Terminals

OK or NG 

OK: Repair or replace harness.

NG: Replace main power window and door lock/unlock switch. Refer to "FRONT DOOR ".