Without Intelligent Key

SYMPTOM 1: 

• Selector lever cannot be moved from "P" position with ignition switch in ON position and brake pedal depressed. 
• Selector lever can be moved from "P" position with ignition key in ON position and brake pedal released. 
• Selector lever can be moved from "P" position when ignition switch is removed from key cylinder. 

SYMPTOM 2: 

• Ignition key cannot be removed when selector lever is set to "P" position. 
• Ignition key can be removed when selector lever is set to any position except "P" position. 

1. CHECK KEY INTERLOCK CABLE

   Check key interlock cable for damage.

   OK or NG 

   OK: GO TO 2.

   NG: Repair key interlock cable. Refer to "REMOVAL AND INSTALLATION ".

2. CHECK CVT POSITION

   Check CVT position. Refer to "CHECKING OF CVT POSITION ".

   OK or NG 

   OK: GO TO 3.

   NG: Adjust control cable. Refer to "ADJUSTMENT OF CVT POSITION ".

3. CHECK SHIFT LOCK SOLENOID AND PARK POSITION SWITCH
   1. Turn ignition switch ON. (Do not start engine.)
   2. Selector lever is set in "P" position.
   3. Check operation sound.
      SHIFT LOCK SOLENOID AND PARK POSITION SWITCH
      
      

      Condition	Brake pedal	Operation sound
      When ignition switch is turned to ON position and selector lever is set in "P" position.	Depressed→Released	Yes
      	Released→Depressed

      OK or NG 

      OK: INSPECTION END 

      NG: GO TO 4.

4. CHECK POWER SOURCE

   Check voltage between CVT shift selector connector M38 terminal 3 and ground.

   OK or NG 

   OK: GO TO  6.

   NG: GO TO 5.

   Fig 1: Checking Voltage Between CVT Shift Selector Connector M38 Terminal 3 And Ground

   Courtesy of NISSAN MOTOR CO., U.S.A.
5. DETECT MALFUNCTIONING ITEM

   Check the following. If any items are damaged, repair or replace damaged parts.

   • Harness for short or open between ignition switch and CVT shift selector connector
   • 10A fuse [No. 12, located in the fuse block (J/B)]
   • Ignition switch, Refer to POWER SUPPLY ROUTING CIRCUIT .

     OK or NG 

     OK: INSPECTION END 

     NG: Repair or replace damaged parts.

6. CHECK STOP LAMP SWITCH POWER SOURCE
   1. Turn ignition switch OFF.
   2. Disconnect stop lamp switch connector E60.
   3. Turn ignition switch ON.
   4. Check voltage between stop lamp switch connector E60 terminal 3 and ground.

      3 - ground : Battery voltage 

      Fig 2: Checking Voltage Between Stop Lamp Switch Connector E60 Terminal 3 And Ground

      Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG 

      OK: GO TO  8.

      NG: GO TO 7.

7. CHECK STOP LAMP SWITCH SUPPLY CIRCUIT
   1. Turn ignition switch OFF.
   2. Disconnect CVT shift selector connector M38.
   3. Check continuity between CVT shift selector connector M38 (A) terminal 4 and stop lamp switch connector E60 (B) terminal 3.

      Continuity should exist. 

   4. Check continuity between CVT shift selector connector M38 (A) terminal 4 and ground.

      Continuity should not exist. 

      Fig 3: Checking Continuity Between stop lamp switch connector E60 (B) terminal 3 And CVT Shift Selector Connector M38 (A) Terminal 4 And Ground

      Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG 

      OK: Replace shift lock solenoid assembly.

      NG: Repair or replace harness as necessary.

8. CHECK GROUND CIRCUIT
   1. Turn ignition switch OFF.
   2. Check continuity between stop lamp switch connector E60 terminal 4 and ground.

      Continuity should exist. 

      Fig 4: Checking Continuity Between Stop Lamp Switch Connector E60 Terminal 4 And Ground

      Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG 

      OK: GO TO 9.

      NG: Repair or replace harness as necessary.

9. CHECK STOP LAMP SWITCH

   Check continuity between stop lamp switch terminals 3 and 4.

   CONTINUITY REFERENCE CHART
   
   

   Condition	Continuity
   When brake pedal is depressed	Yes
   When brake pedal is released	No

   Fig 5: Checking Continuity Between Stop Lamp Switch Terminals 3 And 4

   Courtesy of NISSAN MOTOR CO., U.S.A.

   Check stop lamp switch after adjusting brake pedal.  Refer to BRAKE PEDAL .

   OK or NG 

   OK: INSPECTION END.

   NG: Replace stop lamp switch.