Additional Service When Replacing Transaxle Assembly: Procedure

With CONSULT

1. Set parking brake.
2. Turn ignition switch ON.
3. Select "Work Support" in "TRANSMISSION".
4. Select "ERASE MEMORY DATA".
5. While maintaining the conditions below, touch "Start".
   • Vehicle stop status
   • With engine stopped
   • Selector lever: "R" position
   • Accelerator pedal: Depressed
   NOTE: Select "Start" and complete within approximately 20 seconds.

   Is "COMPLETED" displayed? 

   YES: GO TO 2.

   NO: Turn the ignition switch OFF and wait for a minimum of 10 seconds then perform the work again.

With CONSULT

1. Turn ignition switch OFF with the selector lever in "R" position and wait for 10 seconds or more.
2. Turn ignition switch ON with the selector lever in "R" position.
   CAUTION: Never start the engine.
3. Select "Special function" in "TRANSMISSION".
4. Select "CALIB DATA".
5. Check that indicated value of "CALIB DATA" is equal to the value shown in the following table.

   Item name	Display value	Item name	Display value
   UNIT CLB ID1	00	MAP NO HC/RB	00
   UNIT CLB ID2	00	MAP NO L/B	00
   UNIT CLB ID3	00	OFFSET2 LU	0
   UNIT CLB ID4	00	OFFSET2 PL	0
   UNIT CLB ID5	00	OFFSET2 PRI	0
   UNIT CLB ID6	00	OFFSET2 H/R	0
   UNIT CLB ID7	00	OFFSET2 L/B	0
   UNIT CLB ID8	00	INIT OFFSET H/R A	0
   UNIT CLB ID9	00	INIT OFFSET H/R B	0
   UNIT CLB ID10	00	INIT OFFSET H/R C	0
   UNIT CLB ID11	00	INIT OFFSET H/R D	0
   GAIN LU	256	INIT OFFSET H/R E	0
   GAIN PL	256	INIT OFFSET H/R F	0
   GAIN PRI	256	INIT OFSET LB A	0
   GAIN HC/RB	256	INIT OFSET LB B	0
   GAIN L/B	256	INIT OFSET LB C	0
   OFFSET LU	0	INIT OFSET LB D	0
   OFFSET PL	0	INIT OFSET LB E	0
   OFFSET PRI	0	INIT OFSET LB F	0
   OFFSET HC/RB	0	LB INITIALIZE LEARN	-1
   OFFSET L/B	0	HC INITIALIZE LEARN	-1
   MAP NO LU	00	LB INITIALIZE TEMP	FF
   MAP NO PL	00	LB INITIALIZE TEMP	FF
   MAP NO PRI	00

   Is the indicated value of "CALIB DATA" equal to the value shown in the table? 

   YES: GO TO 3.

   NO: GO TO  1.

1. Shift the selector lever to the "P" position.
2. Check that "P" is displayed on shift position indicator on combination meter.
   NOTE: Displayed approximately 4 - 5 seconds after the selector lever is moved to the "P" position.

   Does shift position indicator display "P"? 

   YES: GO TO  5.

   NO: GO TO 4.

Check the following items:

• Harness between the TCM and the ROM assembly inside the transaxle assembly is open or shorted.
• Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals

  Is the inspection result normal? 

  YES: GO TO  1.

  NO: Repair or replace the malfunctioning parts.

With CONSULT

1. Select "WORK SUPPORT" in "TRANSMISSION".
2. Select "CONFORM CVTF DETERIORTN".
3. Touch "Clear".

   : WORK END