Active Test
The active test is used to determine and identify details of a malfunction, based on self-diagnosis test results and data obtained in the DATA MONITOR. In response to instructions from CONSULT, instead of those from chassis control module on the vehicle, a drive signal is sent to the actuator to check its operation.
CAUTION:
- Never perform ACTIVE TEST while driving the vehicle.
- Always bleed air from brake system before active test.
- Never perform active test when system is malfunctioning.
NOTE:
During an active test, sometimes a chassis control warning is displayed and the master warning lamp illuminates on the information display in the combination meter; however, this is not a malfunction.
| Test item | Operation | Description |
|---|---|---|
| BRAKE ACTUATOR 1 MODE 1 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 1 MODE 2 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 1 MODE 3 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 2 MODE 1 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 2 MODE 2 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 2 MODE 3 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 3 MODE 1 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 3 MODE 2 | Start | Controls brake fluid pressure. |
| BRAKE ACTUATOR 3 MODE 3 | Start | Controls brake fluid pressure. |
| FR TIRE DISP | On | Displays the front RH tire on the information display in the combination meter. |
| Off | Does not display the front RH tire on the information display in the combination meter. | |
| RR TIRE DISP | On | Displays the rear RH tire on the information display in the combination meter. |
| Off | Does not display the rear RH tire on the information display in the combination meter. | |
| STOP LAMP OFF RELAY 2 ACTIVE | On | Displayed, but not use. |
| Off | Displayed, but not use. | |
| MASTER WARNING ACTIVE | On | If touching "On" with the master warning lamp not illuminated, the master warning lamp illuminates. Stops in approximately 1 minute. |
| Off | The master warning lamp turns OFF. (vehicle in normal state) | |
| HDC DISP | On | Displayed, but not use. |
| Off | Displayed, but not use. | |
| BRAKE HOLD DISP | INACT | Does not display the operating status of hill start assist function displayed on the information display in the combination meter. |
| ACTIVE | Displays the operating status of hill start assist function displayed on the information display in the combination meter. | |
| READY | Displays the ready status of hill start assist function displayed on the information display in the combination meter. | |
| ERROR | Does not display the operating status of hill start assist function displayed on the information display in the combination meter. | |
| AEB DISP | On | Displays the operating status of active engine brake (brake control) function displayed on the information display in the combination meter. |
| Off | Does not display the operating status of active engine brake (brake control) function displayed on the information display in the combination meter. | |
| FL TIRE DISP | On | Displays the front LH tire on the information display in the combination meter. |
| Off | Does not display the front LH tire on the information display in the combination meter. | |
| RL TIRE DISP | On | Displays the rear LH tire on the information display in the combination meter. |
| Off | Does not display the rear LH tire on the information display in the combination meter. | |
| VEHICLE DISP | On | Displays the operating status of active ride control (brake control) function displayed on the information display in the combination meter. |
| Off | Does not display the operating status of active ride control (brake control) function displayed on the information display in the combination meter. | |
| INTERRUPT DISP | NO REQ | Does not display the interrupt of hill start assist function displayed on the information display in the combination meter. |
| READY | Displays the interrupt of ready status of hill start assist function displayed on the information display in the combination meter. | |
| ACT | Displays the interrupt of operating status of hill start assist function displayed on the information display in the combination meter. | |
| HDC | Displayed, but not use. | |
| TURN DISP | NO DISP | Does not display the turning status on the information display in the combination meter. |
| LH | Displays the LH turning status on the information display in the combination meter. | |
| RH | Displays the RH turning status on the information display in the combination meter. | |
| ATC 1 DISP | On | Displays the active trace control function on the information display in the combination meter. |
| Off | Does not display the active trace control function on the information display in the combination meter. | |
| ATC 2 DISP | On | Displays the active trace control function on the information display in the combination meter. |
| Off | Does not display the active trace control function on the information display in the combination meter. | |
| ARC DISP | On | Displays the active ride control (brake control) function on the information display in the combination meter. |
| Off | Does not display the active ride control (brake control) function on the information display in the combination meter. | |
| ATC 3 DISP | On | Displays the active trace control function on the information display in the combination meter. |
| Off | Does not display the active trace control function on the information display in the combination meter. | |
| ATC 4 DISP | On | Displays the active trace control function on the information display in the combination meter. |
| Off | Does not display the active trace control function on the information display in the combination meter. | |
| ATC 5 DISP | On | Displays the active trace control function on the information display in the combination meter. |
| Off | Does not display the active trace control function on the information display in the combination meter. |