Data Monitor

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.

: Application : Optional selection

Monitored item	(Unit)	Monitor item selection		Remarks
Monitored item	(Unit)	MAIN SIGNALS	ECU INPUT SIGNALS	Remarks
VSP SENSOR	(km/h or mph)		*	Displays the vehicle speed calculated from the CVT output shaft speed.
ESTM VSP SIG	(km/h or mph)		*	Displays the vehicle speed signal (ABS) received through CAN communication.
PRI SPEED SEN	(RPM)		*	Displays the primary pulley speed calculated from the pulse signal of the primary speed sensor.
SEC REV SENSOR	(RPM)		*	Displays the secondary pulley speed calculated from the pulse signal of the secondary speed sensor.
VHCL/S SE (REV)	(RPM)		*	Displays the CVT output shaft speed calculated from the pulse signal of the output speed sensor.
ENG SPEED SIG	(RPM)		*	Displays the engine speed received through CAN communication.
LINE PRESSURE SEN	(V)		*	Displays the signal voltage of the line pressure sensor.
ATF TEMP SEN	(V)		*	Displays the signal voltage of the CVT fluid temperature sensor.
G SENSOR	(V)		*	Displays the signal voltage of the G sensor.
VIGN SEN	(V)		*	Displays the battery voltage applied to TCM.
VEHICLE SPEED	(km/h or mph)	*		Displays the vehicle speed recognized by TCM.
INPUT REV	(RPM)			Displays the input shaft speed of CVT recognized by TCM.
PRI SPEED	(RPM)	*		Displays the primary pulley speed recognized by TCM.
SEC SPEED	(RPM)			Displays the secondary pulley speed recognized by TCM.
OUTPUT REV	(RPM)			Displays the output shaft speed of CVT recognized by TCM.
ENG SPEED	(RPM)	*		Displays the engine speed recognized by TCM.
SLIP REV	(RPM)	*		Displays the speed difference between the input shaft speed of CVT and the engine speed.
TOTAL GEAR RATIO		*		Displays the total CVT gear ratio calculated from input shaft speed/output shaft speed of CVT.
PULLEY GEAR RATIO		*		Displays the pulley gear ratio calculated from primary pulley speed/secondary pulley speed.
AUX GEARBOX				Displays the gear position of the auxiliary gearbox recognized by TCM.
G SPEED	(G)			Displays the acceleration and deceleration speed of the vehicle calculated from vehicle speed change.
ACCEL POSI SEN 1	(deg)	*	*	Displays the estimated throttle position received through CAN communication.
VENG TRQ	(Nm)	*		Display the engine torque recognized by TCM.
PRI TRQ	(Nm)			Display the input shaft torque of CVT.
TRQ RTO				Display the torque ratio of torque converter.
LINE PRESSURE	(MPa)	*		Displays the secondary pressure (line pressure) calculated from the signal voltage of the secondary pressure sensor.
FLUID TEMP	(°C or °F)	*		Displays the CVT fluid temperature calculated from the signal voltage of the CVT fluid temperature sensor.
DSR REV	(RPM)			Displays the target primary pulley speed calculated from processing of gear shift control.
TRGT GEAR RATIO				Displays the target gear ratio from the input shaft to the output shaft of CVT calculated from processing of gear shift control.
TGT PLLY GR RATIO				Displays the target gear ratio of the pulley from processing of gear shift control.
TRGT AUX GEARBOX				Displays the target gear of the auxiliary gearbox calculated from processing of gear shift control.
LU PRS	(MPa)			Displays the target oil pressure of the torque converter clutch solenoid valve calculated from oil pressure processing of gear shift control.
LINE PRS	(MPa)			Displays the target oil pressure of the line pressure solenoid valve calculated from oil pressure processing of gear shift control.
TRGT PRI PRESSURE	(MPa)			Displays the target oil pressure of the primary pressure solenoid valve calculated from oil pressure processing of gear shift control.
TRGT HC/RB PRESS	(MPa)			Displays the target oil pressure of the high clutch & reverse brake solenoid valve calculated from oil pressure processing of gear shift control.
TRGT LB PRESSURE	(MPa)			Displays the target oil pressure of the low brake solenoid valve calculated from oil pressure processing of gear shift control.
ISOLT1	(A)	*		Displays the command current from TCM to the torque converter clutch solenoid valve.
ISOLT2	(A)	*		Displays the command current from TCM to the line pressure solenoid valve.
PRI SOLENOID	(A)	*		Displays the command current from TCM to the primary pressure solenoid valve.
HC/RB SOLENOID	(A)	*		Displays the command current from TCM to the high clutch & reverse brake solenoid valve.
L/B SOLENOID	(A)	*		Displays the command current from TCM to the low brake solenoid valve.
SOLMON 1	(A)	*	*	Monitors the command current from TCM to the torque converter clutch solenoid valve and displays the monitored value.
SOLMON 2	(A)	*	*	Monitors the command current from TCM to the line pressure solenoid valve and displays the monitored value.
PRI SOL MON	(A)	*	*	Monitors the command current from TCM to the primary pressure solenoid valve and displays the monitored value.
HC/RB SOL MON	(A)	*	*	Monitors the command current from TCM to the high clutch & reverse brake solenoid valve and displays the monitored value.
L/B SOL MON	(A)	*	*	Monitors the current command from TCM to the low brake solenoid valve and displays the monitored value.
D POSITION SW	(On/Off)		*	Displays the operation status of the transmission range switch (D position).
N POSITION SW	(On/Off)		*	Displays the operation status of the transmission range switch (N position).
R POSITION SW	(On/Off)		*	Displays the operation status of the transmission range switch (R position).
P POSITION SW	(On/Off)		*	Displays the operation status of the transmission range switch (P position).
BRAKES W	(On/Off)	*	*	Displays the reception status of the stop lamp switch signal received through CAN communication.
L POSITION SW	(On/Off)		*	Displays the operation status of the transmission range switch (L position).
IDLE SW	(On/Off)	*	*	Displays the reception status of the closed throttle position signal received through CAN communication.
SPORT MODE SW	(On/Off)	*	*	Displays the reception status of the overdrive control switch signal received through CAN communication.
STRDWNSW	(On/Off)		*	Displays the operation status of the paddle shifter (down switch). It is displayed although not equipped.
STRUPSW	(On/Off)		*	Displays the operation status of the paddle shifter (up switch). It is displayed although not equipped.
DOWNLVR	(On/Off)		*	Displays the operation status of the selector lever (down switch). It is displayed although not equipped.
UPLVR	(On/Off)		*	Displays the operation status of the selector lever (up switch). It is displayed although not equipped.
NONMMODE	(On/Off)		*	Displays if the selector lever position is not at the manual shift gate. It is displayed although not equipped.
MMODE	(On/Off)		*	Displays if the selector lever position is at the manual shift gate. It is displayed although not equipped.
INDLRNG	(On/Off)			Displays the transmission status of the shift position (L position) signal transmitted through CAN communication.
INDDRNG	(On/Off)			Displays the transmission status of the shift position (D position) signal transmitted through CAN communication.
INGNRNG	(On/Off)			Displays the transmission status of the shift position (N position) signal transmitted through CAN communication.
INGRRNG	(On/Off)			Displays the transmission status of the shift position (R position) signal transmitted through CAN communication.
INGPRNG	(On/Off)			Displays the transmission status of the shift position (P position) signal transmitted through CAN communication.
CVT LAMP	(On/Off)			Displays the transmission status of the OD OFF indicator lamp signal transmitted through CAN communication.
SPORT MODE IND	(On/Off)			Displays the transmission status of the OD OFF indicator lamp signal transmitted through CAN communication.
MMODE IND	(On/Off)			Displays the transmission status of the manual mode signal transmitted through CAN communication. It is displayed although not equipped.
VDC ON	(On/Off)		*	Displays the reception status of the VDC (ESP) operation signal received through CAN communication. It is displayed although not equipped.
TCS ON	(On/Off)		*	Displays the reception status of the TCS operation signal received through CAN communication. It is displayed although not equipped.
ABS FAIL SIGNAL	(On/Off)		*	Displays the reception status of the ABS malfunction signal received through CAN communication.
ABS ON	(On/Off)		*	Displays the reception status of the ABS operation signal received through CAN communication.
RANGE		*		Displays the gear position recognized by TCM.
M GEAR POS		*		Display the target gear of manual mode
G SEN SLOPE	(%)			Displays the gradient angle calculated from the G sensor signal voltage.
ENGBRKLVL	(On/Off)			Displays the setting of "ENGINE BRAKE ADJ" in "Work Support".
PVIGN VOLT	(V)		*	Displays the backup voltage of TCM.
TRGT AUX GR RATIO				Displays the target gear ratio of the auxiliary gearbox calculated from processing of gear shift control.
G SEN CALIBRATION	(YET/DONE)			Displays the status of "G SENSOR CALIBRATION" in "Work Support".
N IDLE STATUS	(On/Off)			Displays idle neutral status.
CVT-B				Displays CVT fluid temperature count. This monitor item does not use.
CVT-A				Displays CVT fluid temperature count. This monitor item does not use.