FixVault
Home › Pontiac › 2007 › Grand Prix Base › Repair and Diagnosis › Brakes › Anti-Lock Brake System, Traction Control System & Stability Control System › Diagnostic Information and Procedures › DTC C0875 › Test Description

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step tests for specified voltage on the 5-volt reference signal circuit.
  2. 3:  This step checks to see if voltage was below specified voltage.
  3. 4:  This step checks to see if voltage was above specified voltage.
  4. 5:  This step tests for a short to ground in the 5-volt reference circuit of the yaw/lateral accelerometer sensor.
  5. 6:  This step tests for a short to voltage in the 5-volt reference circuit of the yaw/lateral accelerometer sensor.
  6. 7:  This step tests for a high resistance or an open in the ground circuit of the yaw/lateral accelerometer sensor.
  7. 8:  This step checks the yaw/lateral accelerometer sensor connector for poor connections.
  8. 9:  This step checks the EBCM connector for poor connections.
DTC C0875

Step Action Values Yes No
Schematic Reference: Antilock Brake System Schematics 
Connector End View Reference: Antilock Brake System Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Turn OFF the ignition.
  2. Disconnect the electronic brake control module (EBCM).
  3. Install the J 39700  Universal Pinout Box with the J 39700-530  Cable Adapter between the EBCM and the EBCM harness connector. See Special Tools .
  4. Turn ON the ignition, with the engine OFF.
  5. Using the DMM, measure the voltage between pin 16 and pin 15 of the J 39700  .
Is the voltage within the specified value?		 2.1-2.9 V Go to Diagnostic Aids Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the yaw/lateral accelerometer sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. Using the DMM, measure the voltage between pin 16 and pin 15 of the J 39700  .
Is the voltage greater than the specified value?		 2.1 V Go to Step 4  Go to Step 5 
4  Using the DMM, measure the voltage between pin 16 and pin 15 of the J 39700  .
Is the voltage less than the specified value?		 2.9 V Go to Step 8  Go to Step 6 
5  Test the 5-volt reference circuit of the yaw/lateral accelerometer sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 9 
6  Test the 5-volt reference circuit of the yaw/lateral accelerometer sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 7 
7  Test the ground circuit of the yaw/lateral accelerometer sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 9 
8  Inspect for poor connections at the harness connector of the yaw/lateral accelerometer sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 10 
9  Inspect for poor connections at the harness connector of the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 12  Go to Step 11 
10 Replace the yaw/lateral accelerometer sensor. Refer to Yaw Rate Sensor/Lateral Accelerometer Replacement .
Did you complete the replacement?		 - Go to Step 12  -
11 Replace the EBCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 12  -
12
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting test.
Does the DTC reset?		 - Go to Step 2  System OK
About FixVault