FixVault
Home › Porsche › 2004 › Cayenne Base › Repair and Diagnosis › Body & Frame › Door Locks › Rear/Door Convenience System › Fault code 0936 › Diagnosis/troubleshooting

Fault code 0936: Diagnosis/troubleshooting

NOTE: Visual inspection: In the next troubleshooting section, please check first that the affected pins on the passenger's door control module plug connection are neither damaged nor corroded. The wiring and plugs of the affected components must also be checked for external damage and correct contacts. Repair damaged or corroded pins if possible, otherwise replace affected pins. Repair or replace damaged wires.
NOTE: Sporadic faults: In the event of faults that occur sporadically, the wiring positions that are linked to moving parts on and in the vehicle must be checked for each system. Various statuses that can cause faults must be simulated with the help of the wiring diagram.
NOTE: Battery voltage: A battery voltage of between 11.4 and 14.5 V is required for the following troubleshooting procedure. This must be checked and provided, if necessary. On the vehicle electrical system, the voltage to the fuse (input side) must be guaranteed.
NOTE:
  • 'Short circuit to ground' → The fault is detected if there is ground potential for more than five minutes on plug A, pin 4.
  • 'Implausible signal → This fault is detected if the resistance between pins 4 and 19 on plug A is between 360 and 470 Ω.
WORK INSTRUCTION CHART

Work instruction Display OK If not OK
1 Check status of 'switch for passenger's power window'
  • Use the 9588 Porsche System Tester II to switch to the menu 'Input signals/Switch for passenger's power window'.
  • Press the switch in all possible positions.
 Status of 'switch for passenger's power window' stays in one of the following positions:
'Manual up'
'Manual down'
Go to step 2
Status of 'switch for passenger's power window' in at least one position changes to:
'Implausible signal'
Go to step 5
Status of 'switch for passenger's power window' (switch not pressed) is:
'Implausible signal'
Go to step 2
Status of 'switch for passenger's power window' changes according to switch actuation:
'Manual up'
'Automatic Up'
'Manual down'
'Automatic down'
Go to step 8
2 Check switch for passenger's power window
  • Pull plug off 'switch for passenger's power window'.
 Status of 'switch for passenger's power window' changes to:
'Not actuated'
Go to step 7		 Go to step 3
3 Check wiring from passenger's door control module to switch for short circuit to ground
  • Switch off ignition.
  • Measure resistance between control module plug A, pin 4 and ground.
 ∞ Ω
Go to step 4		 Repair wiring.
→ End
4 Check wiring from passenger's door control module to switch for short circuit
  • Measure resistance between pin 4 and pin 19 of control module plug A.
 ∞ Ω
Go to step 8		 Repair wiring.
→ End
5 Check operation of switch for passenger's power window
  • Pull plug off switch for passenger's power window.
  • Measure resistance at the switch between pins 1 and 2.
  • Press the switch in all possible positions.
 'Not actuated'
∞ Ω
'Manual up'
1750 to 1800 Ω
'Manual down'
150 to 170 Ω
Go to step 6		 Go to step 7
6 Check wiring from passenger's door control module to switch for continuity
  • Measure resistance between pin 4 of control module plug A and pin 1 of switch plug.
  • Measure resistance between pin 19 of control module plug A and pin 2 of switch plug.
 < 5 Ω
Go to step 8		 Repair wiring.
→ End
7 Replace switch for passenger's power window → End
8 Replace passenger's door control module → End
About FixVault