Menu "Read Values"
READ VALUES
| Text | Unit | Min. | Max. | Description |
|---|---|---|---|---|
| Engine Speed (Bus from Trionic) | RPM | 0 | 7000 | |
| Vehicle Speed (Output RPM) | km/h | 0 | 250 | Shows the output shaft speed converted to an approximate vehicle speed. The speed is measured with a hall-effect sensor at the toothed wheel on the transmission parking brake. |
| Gearbox Input RPM | RPM | 0 | 7000 | Shows the input shaft speed.The speed is measured at the C1 clutch drum with a halleffect sensor. |
| Solenoid SLT | inactive/active | The solenoid is controlled by the control module with a 300 Hz PWM signal. It is controlled by variations in current and is in the first instance dependent on the throttle position. | ||
| Solenoid SLT Requested pressure |
bar | The TCM calculates the desired value of hydraulic pressure which must be achieved by the valve. The value is the transmission system pressure. The value is controlled so that it is not higher than that which at the present time is required by the clutch or brake in the transmission. | ||
| Solenoid SLT Requested current |
mA | The TCM calculates the desired pressure value. The value is converted to required current. The value is the current which shall flow through the solenoid in order to achieve the correct pressure. | ||
| Solenoid SLT Instantaneous current |
mA | The TCM has calculated the solenoid current in order to achieve the correct pressure. The TCM then regulates the PWM duty cycle so that the instantaneous current is the same as that requested. The value is the instantaneous solenoid current. | ||
| Solenoid SLS | inactive/active | The solenoid is controlled by the control module with a 300 Hz PWM signal. It is controlled by variations in current and is in the first instance dependent on the throttle position. | ||
| Solenoid SLU Requested pressure |
bar | The TCM calculates the desired value of hydraulic pressure which must be achieved by the valve. The value is the pressure which is used by the torque converter. The pressure is modulated so that the input drive is fully or partially engaged or disengaged. | ||
| Solenoid SLU Requested current |
mA | The TCM calculates the desired value of hydraulic pressure which must be achieved by the valve. The value is converted to required current. The value is the current which shall flow through the solenoid in order to achieve the correct pressure. | ||
| Solenoid SLU Instantaneous current |
mA | The TCM has calculated the solenoid current in order to achieve the correct pressure. The TCM then regulates the PWM duty cycle so that the instantaneous current is the same as that requested. The value is the instantaneous solenoid current. | ||
| Solenoid SLU | inactive/active | The solenoid is energized via the control module with B+, depending upon accelerator position and vehicle speed. | ||
| Solenoid SLS Requested pressure |
bar | The TCM calculates the desired value of hydraulic pressure which must be achieved by the valve. The value is the pressure which is used for the clutch or brake currently engaged. The pressure is adjusted so that the accumulator function is obtained (not C1). | ||
| Solenoid SLS Requested current |
mA | The TCM calculates the desired value of hydraulic pressure which must be achieved by the valve. The value is converted to required current. The value is the current which shall flow through the solenoid in order to achieve the correct pressure. | ||
| Solenoid SLS Instantaneous current |
mA | The TCM has calculated the solenoid current in order to achieve the correct pressure. The TCM then regulates the PWM duty cycle so that the instantaneous current is the same as that requested. The value is the instantaneous solenoid current. | ||
| Solenoid S1 Requested status |
ON/OFF | 0 | 1 | The value indicates which solenoid status the TCM requires. With status ON, the control module connects the solenoid, which is grounded via the valve housing, to B+. S1 is normally open and is energized in the following selector lever positions: D and M in 1st gear and R at speeds 7 km/h |
| Solenoid S2 Requested status |
ON/OFF | 0 | 1 | The value indicates which solenoid status the TCM requires. With status ON, the control module connects the solenoid, which is grounded via the valve housing, to B+. S2 is normally open and is energized in the following selector lever positions: D and M in 2nd, 3rd and 4th gears. |
| Solenoid S3 Requested status |
ON/OFF | 0 | 1 | The value indicates which solenoid status the TCM requires. With status ON, the control module connects the solenoid, which is grounded via the valve housing, to B+. S3 is normally closed and is energized in the following selector lever positions: D and M in 1st, 2nd and 3rd gears and R at speeds < 7 km/h. |
| Solenoid S4 Requested status |
ON/OFF | 0 | 1 | The value indicates which solenoid status the TCM requires. With status ON, the control module connects the solenoid, which is grounded via the valve housing, to B+. S4 is normally open and is energized in the following selector lever positions: D and M in 3rd, 4th and 5th gears. |
| Solenoid S5 Requested status |
ON/OFF | 0 | 1 | The value indicates which solenoid status the TCM requires. With status ON, the control module connects the solenoid, which is grounded via the valve housing, to B+. S5 is normally closed and is energized in the following selector lever positions: M in 1st gear and R at speeds < 7 km/h. |
| S1 Current status | ON/OFF | The value indicates the current status on the control module solenoid pin. With status ON the TCM connects B+ to the solenoid which is grounded via the valve housing. | ||
| S2 Current status | ON/OFF | The value indicates the current status on the control module solenoid pin. With status ON the TCM connects B+ to the solenoid which is grounded via the valve housing. | ||
| S3 Current status | ON/OFF | The value indicates the current status on the control module solenoid pin. With status ON the TCM connects B+ to the solenoid which is grounded via the valve housing. | ||
| S4 Current status | ON/OFF | The value indicates the current status on the control module solenoid pin. With status ON the TCM connects B+ to the solenoid which is grounded via the valve housing. | ||
| S5 Current status | ON/OFF | The value indicates the current status on the control module solenoid pin. With status ON the TCM connects B+ to the solenoid which is grounded via the valve housing. | ||
| Accelerator Position (Bus from Trionic) | % | 0 | 100 | Information on the bus comes from the Trionic system. |
| Driver Torque (Bus from Trionic) | Nm | 0 | 400 | Information about the requested engine torque comes on the bus from Trionic |
| Engine Torque (Bus from Trionic) | Nm | -100 | 400 | Engine torque information comes on the bus from the Trionic system. |
| Max Torque Gearbox | Nm | -100 | 400 | The transmission's maximum engine torque. |
| Gearbox Fluid Temperature | °C | -50 | 200 | Shows the transmission fluid temperature. The value is calculated from the voltage measured across the NTC resistor of the sensor. |
| Gearbox Fluid Temperature Sensor | V | 0 | 5 | Shows the voltage measured over the NTC resistor of the sensor. One of the sensor pins is grounded internally and the other is fed with 5V via a resistor built into the control module. The voltage measured over the resistance sinks as the temperature increases. |
| Selector Lever Position 5 Speed | P R N D M L Undefined Failure |
Shows how the selector lever position is interpreted by the TCM on the basis of the status of the 4 contacts A, B, C, and PA. | ||
| Gear Engaged | 0= Gear changing is being carried out 1=GEAR 1 2=GEAR 2 3=GEAR 3 4=GEAR 4 5=GEAR 5 6=Not used 7=Not used 8=Reverse 9=Neutral |
Shows the current gear. | ||
| Special Shift Program | 0=NORMAL 1=SPORT 2=Warm Up Shift Pattern 3=WINTER 4=UP-HILL 1 5=UP-HILL 2 6=HOT 1 7=HOT 2 |
The value shows which type of gear change programme the TCM is using at the moment. | ||
| TCS Active | NO/YES | 0 | 1 | |
| TCC Status | 0=Engaged 1=Engage 2=Disengaged 3=Disengage |
Shows the torque converter status | ||
| TCC Current slipping | RPM | Shows the speed difference between the engine and the transmission input shaft. | ||
| TCC requested slipping | RPM | Shows the TCM requested speed difference between the engine and the transmission input shaft. This must only be compared with the current slipping as the TCM controls the slipping. | ||
| MIL Request | ON/OFF | 0 | 1 | Shows the CHECK ENGINE request from the TCM |
| Gear Position Switch A | ON/OFF | 0 | 1 | Shows the status of the contacts. The 4 contacts A, B, C, and PA are jointly fed with B+. ON is shown in selector lever positions P and R. |
| Gear Position Switch B | ON/OFF | 0 | 1 | Shows the status of thecontacts. The 4 contacts A, B, C, and PA are jointly fed with B+. ON is shown in selector lever positions R, N and D/M |
| Gear Position Switch C | ON/OFF | 0 | 1 | Shows the status of the contacts. The 4 contacts A, B, C, and PA are jointly fed with B+. ON is shown in selector lever position D/M. |
| Gear Position Switch PA | ON/OFF | 0 | 1 | Shows the status of the contacts. The 4 contacts A, B, C, and PA are jointly fed with B+. ON is shown in selector lever positions P and N. |
| Brake Light Switch (Bus from TWICE) | ON/OFF | 0 | 1 | Shows activation of the brake light switch. Depressing the brake pedal closes the brake light switch. Information comes on the bus from TWICE. |
| Kick-Down Status (Bus from Trionic) | ON/OFF | 0 | 1 | Shows if the operational mode is active. |
| SPORT Lamp | ON/OFF | 0 | 1 | The sport lamp comes on when the SPORT shifting programme is activated. |
| WINTER Lamp | ON/OFF | 0 | 1 | Shows if the TCM is requesting that the WINTER light shall be illuminated. |
| Winter Switch | ON/OFF | 0 | 1 | The WINTER shifting programme is activated via the winter switch on the console. The winter switch is spring-loaded. When pressed, ON is displayed. |
| Sport Switch | ON/OFF | 0 | 1 | The SPORT shifting programme is activated by means of the sport switch on the selector lever. The sport switch is spring-loaded. When pressed, ON is displayed. |
| CHECK GEARBOX Lamp | ON/OFF | 0 | 1 | |
| Sentronic gear change request | None/Up/Down | Shows if and in which direction Sentronic is gear changing. | ||
| Brake Mode | ON/OFF | 0 | 1 | Shows if the operational mode is active. |
| Sentronics Mode | ON/OFF | 0 | 1 | Shows if the operational mode is active. |
| Fuel shut-off (Fuel Cut Inhibit Mode) | ON/OFF | 0 | 1 | Shows if the operational mode is active. |
| Warm Up Shift Pattern Mode | ON/OFF | 0 | 1 | Shows if the operational mode is active. |
| Winter Mode | ON/OFF | 0 | 1 | Shows if the operational mode is active. |
| Sport Mode | ON/OFF | 0 | 1 | Shows if the operational mode is active. |
| Gear ratio situation (Gear Ratio) | Shows the current gear ratio situation. The value is calculated from the input and output shaft speeds. |