FixVault
Home › Saturn › 2005 › Relay AWD › Repair and Diagnosis › External Pages › Different car › Section 18 (Supplemental Inflatable Restraint System) › Repair Instructions › SIR Disabling and Enabling Zone 8 › Enabling Procedure

Enabling Procedure

WARNING: This page is about a different car, the 2005 Chevrolet Malibu. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove the key from the ignition switch.
    2. Fig 1: Locating Roof Rail Module Connector
    GM899820Courtesy of GENERAL MOTORS CORP.
  2. Connect the roof rail module-left connector to the vehicle harness connector.
  3. Install the CPA to the roof rail module-left connector.
  4. Install the garnish molding to the left upper lock pillar. Refer to Garnish Molding Replacement - Rear Corner Upper in Interior Trim.
    5. Fig 2: View Of Seat Belt Pretensioner Connector And Wiring Harness Routing
    GM899818Courtesy of GENERAL MOTORS CORP.
  5. Connect the seat belt pretensioner-LF connector.
  6. Install the CPA to the seat belt pretensioner-LF connector.
  7. Install the left/driver lower center pillar trim. Refer to Garnish Molding Replacement - Center Pillar Lower in Interior Trim.
    8. Fig 3: View Of Door Switch & Air Bag Electrical Connectors Behind Left Trim Panel
    GM877766Courtesy of GENERAL MOTORS CORP.
  8. Connect the steering wheel module coil connector to the vehicle harness connector.
  9. Install the CPA to the steering wheel module coil connector.
  10. Install the driver/left outer trim cover to the I/P. Refer to Instrument Panel (I/P) Outer Trim Cover Replacement in Instrument Panel, Gages, and Console.
    11. Fig 4: Identifying I/P Module Connector To Vehicle Harness Connector
    GM816857Courtesy of GENERAL MOTORS CORP.
  11. Connect the I/P module connector (1) to the vehicle harness connector (2).
  12. Install the CPA to the I/P module connector (1).
  13. Install the passenger/right outer trim cover to the I/P (3). Refer to Instrument Panel (I/P) Outer Trim Cover Replacement in Instrument Panel, Gages, and Console.
    14. Fig 5: View Of Seat Belt Pretensioner Connector And Wiring Harness Routing
    GM899818Courtesy of GENERAL MOTORS CORP.
  14. Connect the seat belt pretensioner-RF connector.
  15. Install the CPA to the seat belt pretensioner-RF connector.
  16. Install the right lower center pillar trim. Refer to Garnish Molding Replacement - Center Pillar Lower in Interior Trim.
    17. Fig 6: Locating Roof Rail Module Connector
    GM899820Courtesy of GENERAL MOTORS CORP.
  17. Connect the roof rail module-right connector to the vehicle harness connector.
  18. Install the CPA to the roof rail module-right connector.
  19. Install the garnish molding to the right upper lock pillar. Refer to Garnish Molding Replacement - Rear Corner Upper in Interior Trim.
    20. Fig 7: Locating AIR BAG (IGN) And AIR BAG (BATT) Fuses In Fuse Center
    GM1316302Courtesy of GENERAL MOTORS CORP.
  20. Install the AIR BAG (IGN) and AIR BAG (BATT) fuses into the BCM fuse center.
  21. Install the BCM fuse center cover.
  22. Use caution while reaching in and turn the ignition switch to the ON position.

    The AIR BAG indicator will flash then turn OFF.

  23. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described. Refer to Diagnostic System Check - Vehicle in Vehicle DTC Information.
About FixVault