Mode 6 - 2005 Scion: XA
TID $04: HO2S HEATER
| TLT | CID | Unit Conversion | Description of Test Value | Description of Test Limit |
|---|---|---|---|---|
| 1 | $01 | Multiply by 0.000076 [A] | Maximum HO2S heater current (Bank 1 Sensor 1) | Malfunction threshold for HO2S heater |
| 1 | $02 | Multiply by 0.000076 [A] | Maximum HO2S heater current (Bank 1 Sensor 2) | Malfunction threshold for HO2S heater |
TID $08: THERMOSTAT
| TLT | CID | Unit Conversion | Description Test Value | Description of Test Limit |
|---|---|---|---|---|
| 0 | $01 | Multiply by 0.625 and subtract 40°C | ECT sensor output when estimated ECT has reached to malfunction criterion | malfunction criterion for thermostat |
O2S TEST RESULTS
| TID | Unit Conversion | Description of Test Value | Malfunction Criterion |
|---|---|---|---|
| $07 | Multiply by 0.005 (V) | Minimum sensor voltage | Less than 0.4 V |
| $08 | Multiply by 0.005 (V) | Minimum sensor voltage | More than 0.55 V |
| $81 | Multiply by 0.001 (Second) | Continuous time that HO2S voltage is outside operating range | Varies with operating conditions |
O2S TEST RESULT (MODE 05 DATA)
| TID | Unit Conversion | Description of Test Value | Malfunction Criterion |
|---|---|---|---|
| $03 | Multiply by 0.005 (V) | This value is used to calculate TID $31 and $32 | - |
| $04 | Multiply by 0.005 (V) | This value is used to calculate TID $31 and $32 | - |
| $31 | Multiply by 0.04 (Second) | Lean to Rich switch time | Less than 0.9 seconds |
| $32 | Multiply by 0.04 (Second) | Rich to Lean switch time | Less than 0.9 seconds |
| $38 | Multiply by 0.04 (Second) | Average time per one cycle of HO2S voltage | Varies with operating conditions |
O2S TEST RESULTS
| TID | Unit Conversion | Description of Test Value | Malfunction Criterion |
|---|---|---|---|
| $07 | Multiply by 0.005 (V) | Minimum sensor voltage | 0.4 V (or less) |
| $08 | Multiply by 0.005 (V) | Minimum sensor voltage | 0.5 V (or more) |
| $31 | Multiply by 0.04 (Second) | Lean to Rich switch time (This test value is not use malfunction determination) | - |
| $32 | Multiply by 0.04 (Second) | Rich to Lean switch time (This test value is not use malfunction determination) | - |
| $37 | Multiply by 0.04 (Second) | Rich to Lean switch time during fuel-cut (This test value is not use malfunction determination) | - |
| $39 | Multiply by 0.04 (Second) | Time that HO2S voltage drops from 0.35 V to 0.2 V during fuel-cut (This test value is not use malfunction determination) | - |
| $81 | Multiply by 0.39 (%) | Percentage in monitor time that sensor voltage is less than 0.05 V | 60% (or more) |
| $84 | Multiply by 0.39 (%) | Percentage in monitor time that sensor voltage is more than 0.7 V | 20% (or less) |
| $85 | Multiply by 0.26 (Second) | Duration that sensor voltage is 0.45 V or higher | 20 seconds (or less) |
| $87 | Multiply by 0.39 (%) | Percentage in monitor time that sensor voltage is more than 0.45 V | 40% (or less) |
TID $01: CATALYST TEST RESULT
| TLT | CID | Unit Conversion | Description of Test Value | Description of Test Limit |
|---|---|---|---|---|
| 0 | $01 | Multiply by 0.0078 [no dimension] Catalyst deterioration level bank 1: |
Determined by waveforms of HO2S sensor 1 and sensor 2 | Malfunction criteria for catalyst deterioration |
TID $02: EVAP - LEV II VACUUM MONITOR
| TLT | CID | Unit Conversion | Description of Test Value | Description of Test Limit |
|---|---|---|---|---|
| 1 | $01 | Multiply by 0.0183 [mmHg] | Test value of EVAP VSV stuck close: Determined by fuel tank pressure change during vacuum introduction |
Malfunction criteria for EVAP VSV stuck close |
| 0 | $02 | Multiply by 0.0655 [seconds] | Test value of EVAP VSV stuck open: Determined by duration that fuel tank pressure is higher than criteria |
Malfunction criteria for EVAP VSV stuck open |
| 0 | $03 | Multiply by 0.0655 [seconds] | Test value of canister closed valve (CCV): Determined by duration that fuel tank pressure is lower than criteria |
Malfunction criteria for CCV |
| 0 | $04 | Multiply by 0.0458 [mmHg] | Test value of 0.04 inch leak: Determined by fuel tank pressure change |
Malfunction criteria for 0.04 inch leak |
| 0 | $05 | Multiply by 0.0458 subtract 2.93 [mmHg] | Test value of 0.02 inch leak: Determined by fuel tank pressure change |
Malfunction criteria for 0.02 inch leak |