FixVault
Home › Subaru › 2006 › Impreza Outback Sport, Automatic › Repair and Diagnosis › Transmission › Automatic Trans › Automatic Transmission › Front Vehicle Speed Sensor › Installation

Front Vehicle Speed Sensor: Installation

  1. Pass the harness assembly through the hole in the transmission case.
    Fig 1: Identifying Harness Connector And Transmission Ground
    G05002532
  2. Connect the harness connector and transmission ground.

    Tightening torque: 8 N.m (0.8 kgf-m, 5.8 ft-lb) 

    Fig 2: Identifying Transmission Ground And Harness Connector
    G05002533
  3. Apply proper amount of liquid gasket to the entire oil pan mating surface.

    Liquid gasket: THREE BOND 1217B (Part No. K0877YA020) 

    Fig 3: Identifying Area Of Liquid Gasket To Entire Oil Pan Mating Surface
    G05002534
  4. Apply liquid gasket fully to three holes other than screw holes on transmission case.

    Liquid gasket: THREE BOND 1217B (Part No. K0877YA020) 

    Fig 4: Locating Oil Pan
    G05002535
  5. Install the oil pan.

    Tightening torque: 5 N.m (0.5 kgf-m, 3.6 ft-lb) 

  6. Connect the connector of rear vehicle speed sensor. (MP-T model)
    Fig 5: Identifying Rear Vehicle Speed Sensor
    G05002536
  7. Connect the connector of rear vehicle speed sensor. (VTD model)
    Fig 6: Identifying Rear Vehicle Speed Sensor
    G05002537
  8. Install the front vehicle speed sensor and torque converter turbine speed sensor, and then fasten the harness.

    Tightening torque: 7 N.m (0.7 kgf-m, 5.1 ft-lb) 

    Fig 7: Identifying Front Vehicle Speed Sensor And Torque Converter Turbine Speed Sensor
    G05002538
  9. Install the inlet pipe.
    NOTE: Be sure to use a new copper washer.

    Tightening torque: 

    T1: 25 N.m (2.5 kgf-m, 18.4 ft-lb) 

    T2: 45 N.m (4.6 kgf-m, 33 ft-lb) 

    T3: 40 N.m (4.1 kgf-m, 29.5 ft-lb) 

    Fig 8: Identifying Inlet Pipe
    G05002539
  10. Install the transmission rear crossmember bolts.

    Tightening torque: 70 N.m (7.1 kgf-m, 51 ft-lb) 

  11. Install the propeller shaft. < Ref. to INSTALLATION , Propeller Shaft. >
  12. Install the front, center, rear exhaust pipes and muffler. (Non-turbo model)

    < Ref. to INSTALLATION , Front Exhaust Pipe. > < Ref. to INSTALLATION , Rear Exhaust Pipe. > < Ref. to INSTALLATION , Muffler. >

  13. Install the center, rear exhaust pipes and muffler. (Turbo model)

    < Ref. to INSTALLATION , Center Exhaust Pipe. > < Ref. to INSTALLATION , Rear Exhaust Pipe. > < Ref. to INSTALLATION , Muffler. >

  14. Lower the vehicle.
  15. Install the transmission connector to the stay.
  16. Install the pitching stopper. < Ref. to INSTALLATION , Transmission Mounting System. >
  17. Install the air intake chamber. (Non-turbo model) < Ref. to INSTALLATION , Air Intake Chamber. >
  18. Install the intercooler. (Turbo model)

    < Ref. to INSTALLATION , Intercooler. >

About FixVault