FixVault
Home › Subaru › 2013 › BRZ Limited, Automatic Trans › Repair and Diagnosis › External Pages › Different car › Section 118 (Cruise Control System) › Cruise Control System › List Of Cancel Codes

List Of Cancel Codes

WARNING: This page is about a different car, the 2019 Subaru BRZ. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • The cancel code is registered even when cancel is performed intentionally by the driver.
  • Cancel codes are cleared if the ignition switch is turned to OFF.
  • If a different cancel code is input after a cancel code (latest code) has been input, the latest code is overwritten.
  • If the cruise indicator light turns yellow, a malfunction is occurring in the system or cruise control related switch. The cancel code at this time is saved even after ignition switch is OFF as a memory code of a past malfunction.
  • To display a cancel code, use the Subaru Select Monitor to read the code after the cruise control is deactivated during a driving test.
Cancel code Item Content of diagnosis Note
11 [Main switch] ON-OFF switch of cruise control main switch is turned to OFF, and then the cruise control is released. This code is displayed without operating the ON-OFF switch. Refer to CANCEL CODE 11 .
12 [Stop & Brake switch] Stop light switch or brake switch is turned to ON, and then the cruise control is released. This code is displayed without depressing the brake pedal. Refer to CANCEL CODE 12 .
13 [Clutch switch] Clutch switch is turned to ON, and then the cruise control is released. This code is displayed without depressing the clutch pedal. Refer to CANCEL CODE 13 .
14 [Neutral switch] Neutral position switch is turned to ON, and then the cruise control is released. This code is displayed without shifting to neutral position. Refer to CANCEL CODE 14 .
15 [Cancel switch] Cancel switch is turned to ON, and then the cruise control is released. This code is displayed without operating the cancel switch. Refer to CANCEL CODE 15 .
16 [Ignition Switch] Ignition switch is turned to OFF, and then the cruise control is released. This code is displayed without operating the ignition switch. Refer to CANCEL CODE 16 .
22 [Abnormality of change in vehicle speed] Malfunction of vehicle speed signal variation is detected. Refer to CANCEL CODE 22 .
24 [Abnormality of switches related to cruise control] Open circuit of cruise control switch is detected during cruise driving. (The system is judged as model without cruise control.) This code is displayed with normal operation. Refer to CANCEL CODE 24 .
31 [Abnormal engine speed Signal]
  • Abnormal increase of engine speed is detected.
  • Gear is placed in Neutral, 1st or Reverse position.
 Cruise in 2nd shift position or more. Refer to CANCEL CODE 31 .
32 [Cruse Control out of Range]
  • Controlled vehicle speed decreased under the limit during cruising.
  • Set operation was performed at vehicle speed unavailable for setting.
  • RESUME operation was performed without memorized vehicle speed.
 This code is displayed, though the vehicle speed is increased to the speed available for cruise set and set operation was performed again. Refer to CANCEL CODE 32 .
34 [Prohibition of cruise control at continuing big Accel. angle] The vehicle has been driven at higher speed than set vehicle speed for an abnormally long time (approximately 10 minutes) during cruise driving. This code is displayed when driving for a long period of time at higher speed than appropriate cruise set vehicle speed by operating accelerator pedal. In this case, the cruise setting is deactivated. Refer to CANCEL CODE 34 .
35 [Prohibition of cruise control at vehicle speed F/B malfunction] Set vehicle speed cannot be kept because of some reasons (steep uphill, parking brake, abnormal decrease of engine output, etc.) during cruise driving. This code is displayed when driving condition is not suitable for cruise control. Perform cruise set operation again after clearing the possible cause. Refer to CANCEL CODE 35 .
41 [VDC/TCS Operating] Vehicle dynamics control (VDC) or TCS is activated during cruise driving or cruise setting. This code is displayed when driving condition is not suitable for cruise control. Perform cruise set operation again after clearing the possible cause. Refer to CANCEL CODE 41 .
43 [ABS/VDC Failure]
  • During cruise driving or cruise setting, the situation that some or all functions for ABS or VDC can not work is detected.
  • CRUISE indicator does not illuminate even though you pressed the CRUISE switch before starting the engine.
 Refer to CANCEL CODE 43 .
45 [Meter Failure] Combination meter malfunction is detected during cruise driving or cruise setting. Refer to CANCEL CODE 45 .
49 [TCM Failure] Transmission control module (TCM) malfunction is detected during cruise driving or cruise setting. Refer to CANCEL CODE 49 .
61 [Brake switch abnormal] Malfunction in the stop light & brake switch is detected. Refer to CANCEL CODE 61 .
62 [Neutral Switch Failure] Neutral position switch malfunction is detected. Refer to CANCEL CODE 62 .
63 [Abnormality 1 of change in vehicle speed] Malfunction of vehicle speed signal variation is detected. Refer to CANCEL CODE 63 .
64 [Engine Sensor Failure 1] Malfunction related to engine is detected. Refer to CANCEL CODE 64 .
65 [Abnormality 1 of switches related to cruise control] Cruise control command switch malfunction is detected. (When the switch is pressed ON for a long time (approximately two minutes), stuck ON condition is detected.) Refer to CANCEL CODE 65 .
About FixVault