Inspection Mode 2
WARNING: This page is about a different variant/trim than selected.
| Code | Note | Number of driving cycles on the detecting condition |
|---|---|---|
| P0D5611 | - | 1 |
| P0E5E49 | - | 1 |
| P0E5E87 | - | 1 |
| P1C1F49 | - | 1 |
| P1CED1C | - | 1 |
| P1CF01C | - | 1 |
| P1CF31C | - | 1 |
| P0D2A19 | - | 1 |
| P0D3812 | - | 1 |
| P0D3814 | - | 1 |
| P0D3828 | - | 1 |
| P0D389E | - | 1 |
| P0D3D16 | - | 1 |
| P0D3D17 | - | 1 |
| P0D4C12 | - | 1 |
| P0D4C14 | - | 1 |
| P0D5C00 | - | 1 |
| P1C0012 | - | 1 |
| P1C0014 | - | 1 |
| P1C0016 | - | 1 |
| P1C009E | - | 1 |
| P1C0512 | - | 1 |
| P1C0514 | - | 1 |
| P1C0A12 | - | 1 |
| P1C0A14 | - | 1 |
| P1C1012 | - | 1 |
| P1C1014 | - | 1 |
| P1C1028 | - | 1 |
| P1C109E | - | 1 |
| P1C1516 | - | 1 |
| P1C1517 | - | 1 |
| P1C1B00 | - | 1 |
| P1C1C00 | - | 1 |
| P1C1D00 | - | 1 |
| P1C1E00 | - | 1 |
| P1C2617 | - | 1 |
| P1C2717 | - | 1 |
| P1C2819 | - | 1 |
| P1CA400 | - | 1 |
| P1CCD9E | - | 1 |
| P1CCD9F | - | 1 |
| P1CCE14 | - | 1 |
| P1CF662 | - | 1 |
Diagnostic procedure:
- Using the Subaru Select Monitor, perform the clear memory of [Plug-in Battery Charger]. Ref. to COMMON (DIAG)>CLEAR MEMORY .
- Turn to IG OFF, and wait for two minutes or more.
- Using the Subaru Select Monitor, read the DTC of [Plug-in Battery Charger] to check that there is no DTC displayed. Ref. to PLUG-IN BATTERY CHARGER (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .NOTE: If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs. After solving the DTC, repeat from step 1.
- Using the Subaru Select Monitor, check [Data Monitor] of [P-HEV High Voltage Battery] to see if [Hybrid Battery SOC] is less than 70%. Ref. to P-HEV HIGH VOLTAGE BATTERY (DIAGNOSTICS)>DATA MONITOR .
- Turn to IG OFF, and wait for two minutes or more.
- Connect Electric vehicle charger cable assembly, and charge it for 30 seconds or more.
- Disconnect Electric vehicle charger cable assembly and wait for 10 seconds or more.
- Read the [Readiness code] of [Plug-in Battery Charger] using Subaru Select Monitor and check that the concerned self-diagnosis is completed. Ref. to PLUG-IN BATTERY CHARGER (DIAGNOSTICS)>ALL READINESS DIAGNOSTIC CODE(S) .NOTE: If the concerned DTC is displayed, the self-diagnosis of the DTC is not complete. Repeat from step 4.
- Using the Subaru Select Monitor, read the DTC of [Plug-in Battery Charger] to check that there is no DTC displayed. Ref. to PLUG-IN BATTERY CHARGER (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .NOTE: If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.