Check Power Rear Gate Lock Button
- CHECK BODY INTEGRATED UNIT SETTING
.
- Turn the ignition switch to ON.
- Display the [Power rear gate setting] data using Subaru Select Monitor. Ref. to BODY CONTROL (DIAGNOSTICS)>CUSTOMIZE .
Is the setting in the [Support]?
YES: Go to 2.
NO: Turn the setting to [X].
- CHECK DTC
.
Read DTCs of [Body Control], [Power Rear Gate] and [Keyless Access with Push Button Start] using the Subaru Select Monitor. Ref. to COMMON (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .
Is a DTC detected for each system?
YES: Perform a check according to the DTC.
NO: Go to 3.
- CHECK KEYLESS ACCESS CONTROL MODULE
.
Display the [Rear Gate Request SW] data using Subaru Select Monitor. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DATA MONITOR .
Does the display change to [OFF] ←→> [ON], when the button is operated [OFF] ←→> [ON] position for power rear gate?
YES: Go to 4.
NO: Replace the keyless access control module. Ref. to SECURITY AND LOCKS>KEYLESS ACCESS CONTROL MODULE .
- CHECK POWER REAR GATE LOCK BUTTON
.
- Turn the ignition switch to OFF.
- Disconnect the power rear gate lock switch connector.
- Measure the resistance between rear gate lock button terminals. Ref. to POWER REAR GATE SYSTEM>POWER REAR GATE INNER SWITCH>INSPECTION .
Is power rear gate lock button normal?
YES: Go to 5.
NO: Replace the power rear gate lock button. Ref. to POWER REAR GATE SYSTEM>POWER REAR GATE INNER SWITCH .
- CHECK HARNESS
.
Measure the resistance between power rear gate lock button and keyless access control module.
Connector & terminal
(D162) No. 4 - (i75) No. 17:
Is the resistance less than 10 Ω?
YES: Go to 6.
NO: Repair or replace the harness.
- CHECK HARNESS
.
Measure the resistance between power rear gate lock button and chassis ground.
Connector & terminal
(D162) No. 1 - Chassis ground:
Is the resistance less than 10 Ω?
YES: Go to 7.
NO: No Repair or replace the harness.
- CHECK POWER REAR GATE CONTROL MODULE
.
- Turn the ignition switch to ON.
- Display the [PRG State 2] data using Subaru Select Monitor. Ref. to POWER REAR GATE (DIAGNOSTICS)>DATA MONITOR .
Is [Fully open] displayed on [PRG State] by operating the rear gate to fully open?
YES: Go to 8.
NO: No Refer to "Basic Diagnostic Procedure" of "POWER REAR GATE SYSTEM (DIAGNOSTICS)". Ref. to POWER REAR GATE (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
- CHECK POWER REAR GATE CONTROL MODULE
.
Display the [PRG State 2] data using Subaru Select Monitor. Ref. to POWER REAR GATE (DIAGNOSTICS)>DATA MONITOR .
Is [Half Stop] displayed on [PRG State] by operating the rear gate to the middle stop position?
YES: Go to 9.
NO: No Refer to "Basic Diagnostic Procedure" of "POWER REAR GATE SYSTEM (DIAGNOSTICS)". Ref. to POWER REAR GATE (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
- CHECK POWER REAR GATE CONTROL MODULE
.
Display the [PRG State 2] data using Subaru Select Monitor. Ref. to POWER REAR GATE (DIAGNOSTICS)>DATA MONITOR .
Is [Totally-enclosed] displayed on [PRG State] by operating the rear gate to fully closed?
YES: Go to 10.
NO: No Refer to "Basic Diagnostic Procedure" of "POWER REAR GATE SYSTEM (DIAGNOSTICS)". Ref. to POWER REAR GATE (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
- CHECK POWER REAR GATE CONTROL MODULE
.
Display the [PRG State 2] data using Subaru Select Monitor. Ref. to POWER REAR GATE (DIAGNOSTICS)> DATA MONITOR .
Is [Operating] displayed on [PRG State] by keeping the rear gate in operation?
YES: Go to 11.
NO: No Refer to "Basic Diagnostic Procedure" of "POWER REAR GATE SYSTEM (DIAGNOSTICS)". Ref. to POWER REAR GATE (DIAGNOSTICS)>BASIC DIAGNOSTIC PROCEDURE .
- CHECK OPERATION OF POWER REAR GATE LOCK BUTTON FUNCTION
.
- Turn the ignition switch to OFF and close all doors.
- Press the power rear gate lock button while carrying the access key with you with the rear gate fully open.
Do all the doors lock?
YES: Finish this operation because it is normal.
NO: Ref. to SECURITY AND LOCKS>DOOR LOCK CONTROL SYSTEM>INSPECTION>CHECK DOOR SWITCH .