FixVault
Home › Tesla › 2021 › Model S Performance › Repair and Diagnosis › External Pages › Different car › Section 33 (Instrument Panel -- Model Y) › Instrument Panel › IP Carrier - Remove And Install › Install

IP Carrier - Remove And Install: Install

WARNING: This page is about a different car, the 2024 Tesla Model Y, 2023 Tesla Model Y, 2022 Tesla Model Y, 2021 Tesla Model Y, and 2020 Tesla Model Y. However, it is still accessible from the selected car via links, so may be relevant.
  1. Install IP carrier onto cross car beam
    NOTE: Recommend assistance, Be cautious to clear harness clipped at top center of HVAC assembly
    G00651151Courtesy of TESLA, INC.
  2. Install screw securing IP carrier to cross car beam on upper RH side
    NOTE: 1x screw, T20, 2.3 Nm
    G00651150Courtesy of TESLA, INC.
  3. Install screws securing IP carrier to cross car beam at upper center
    NOTE: 2x screws, T20, 2.3 Nm
    G00651149Courtesy of TESLA, INC.
  4. Install screws securing IP carrier to cross car beam at lower center
    NOTE: 2x screws, T20, 2.3 Nm
    G00651152Courtesy of TESLA, INC.
  5. Install screw securing IP carrier to cross car beam on upper LH side
    NOTE: 1x screw, T20, 2.3 Nm
    G00651147Courtesy of TESLA, INC.
  6. Install screws securing IP carrier to cross car beam on lower LH side
    NOTE: 2x screws, T20, 2.3 Nm
    G00651146Courtesy of TESLA, INC.
  7. Install screws securing LH side of IP carrier to cross car beam near passenger air bag
    NOTE: 2x screws, T20, 2.3 Nm
    G00651153Courtesy of TESLA, INC.
    G00651154Courtesy of TESLA, INC.
  8. Install passenger air bag into IP carrier and secure bolts
    NOTE: 4x patch bolts, E10, 8 Nm, Install new patch bolts
    G00651155Courtesy of TESLA, INC.
  9. Install connectors for passenger air bag
    NOTE: 3x connectors, 2x connectors for regions other than North America
    G00651156Courtesy of TESLA, INC.
  10. Install RH speaker to IP carrier
    NOTE: 3x screws, T20, 2.3 Nm, 1x connector
    G00651142Courtesy of TESLA, INC.
    G00651135Courtesy of TESLA, INC.
  11. Secure center tweeter connector onto speaker harness
    NOTE: Do not install center tweeter, Use black tape, Yellow tape used in picture for demonstration purposes only
    G00651157Courtesy of TESLA, INC.
    G00651158Courtesy of TESLA, INC.
  12. Cover center tweeter hole
    NOTE: Cut butyl then install, Make sure butyl does not cover IP clips or interfere with speaker perimeter
    G00651159Courtesy of TESLA, INC.
    G00651160Courtesy of TESLA, INC.
    G00651161Courtesy of TESLA, INC.
    G00651162Courtesy of TESLA, INC.
  13. Install center speaker to IP
    NOTE: 3x screws, T20, 2.3 Nm, 1x connector
    G00651163Courtesy of TESLA, INC.
  14. Install LH speaker to IP carrier
    NOTE: 3x screws, T20, 2.3 Nm, 1x connector
    G00651164Courtesy of TESLA, INC.
  15. Position defroster grill and lower tabs into position on IP
    NOTE: 6x tabs
    G00651134Courtesy of TESLA, INC.
    G00651133Courtesy of TESLA, INC.
  16. Secure clips securing defroster grill

    9x clips

    G00651165Courtesy of TESLA, INC.
  17. Position LH air duct into IP and connect harness connector

    1x connector

    G00651166Courtesy of TESLA, INC.
  18. Install LH air duct into IP
    NOTE: 1x screw, T20, 2.3 Nm
    G00651167Courtesy of TESLA, INC.
  19. Position RH air duct into IP and connect harness connector
    NOTE: 1x connector
    G00651168Courtesy of TESLA, INC.
  20. Install RH air duct into IP
    NOTE: 1x screw, T20, 2.3 Nm
    G00651169Courtesy of TESLA, INC.
  21. Install IP brow finisher into vehicle
    NOTE: 16x clips, Need to lift top pad up slightly to slide IP brow finisher into position
    G00651128Courtesy of TESLA, INC.
  22. Install screws securing RH side of IP brow finisher
    NOTE: 4x screws, T20, 2.3 Nm, Fastener count may vary, Older production vehicles may have 5x screws
    G00651127Courtesy of TESLA, INC.
  23. Install screws securing LH side of IP brow finisher
    NOTE: 4x screws, T20, 2.3 Nm, Fastener count may vary, Older production vehicles may have 5x screws
    G00651126Courtesy of TESLA, INC.
  24. Install the RH IP air wave duct
    NOTE: 2x push clips
    G00651170Courtesy of TESLA, INC.
  25. Install the passenger footwell air duct
    NOTE: 1x push clip
    G00650851Courtesy of TESLA, INC.
  26. Install the glove box into IP carrier
    NOTE: 3x clips
    G00651123Courtesy of TESLA, INC.
  27. Connect glove box assembly connectors
    NOTE: 3x connectors, New puddle lamp harness routing prevent blocking movement of pawls
    G00650852Courtesy of TESLA, INC.
  28. Install screws securing glove box assembly to IP carrier
    NOTE: 6x screws, T20, 2.3 Nm
    G00650853Courtesy of TESLA, INC.
    G00650854Courtesy of TESLA, INC.
    G00650855Courtesy of TESLA, INC.
  29. Position center display neck housing into vehicle
    G00650856Courtesy of TESLA, INC.
  30. Position center display into vehicle
    G00651117Courtesy of TESLA, INC.
  31. Connect center display
    NOTE: 1x connector
    G00650857Courtesy of TESLA, INC.
  32. Install retaining clip to center display connector
    NOTE: 1x clip
    G00650858Courtesy of TESLA, INC.
  33. Slide down neck housing and install bolts securing neck housing to center display
    NOTE: 2x bolts, T30, 3 Nm,
    G00650859Courtesy of TESLA, INC.
    G00650860Courtesy of TESLA, INC.
  34. Install center display to IP carrier
    NOTE: 2x patch bolts, 10mm, 16 Nm, Install new patch bolts, Slide towards front of vehicle
    G00650861Courtesy of TESLA, INC.
  35. Connect temperature sensor connector and install IP service panel into IP
    NOTE: 4x clips, 4x tabs, 1x connector
    G00650862Courtesy of TESLA, INC.
    G00650863Courtesy of TESLA, INC.
  36. Install SCCM onto steering column
    G00650864Courtesy of TESLA, INC.
  37. Install bolt securing SCCM to steering column
    NOTE: 1x bolt, 5mm allen, 9 Nm
    G00650865Courtesy of TESLA, INC.
  38. Connect steering column control module (SCCM) assembly connector
    NOTE: 1x connector, Install new orange retaining clip to connector then install SCCM connector, Perform push-pull-push to make sure connector is seated properly
    G00650866Courtesy of TESLA, INC.
    G00650867Courtesy of TESLA, INC.
  39. Install lower shroud onto steering column
    G00650868Courtesy of TESLA, INC.
    G00650869Courtesy of TESLA, INC.
  40. Install lower screw securing lower shroud to steering column
    NOTE: 1x screw, T20, 1.5 Nm
    G00651105Courtesy of TESLA, INC.
  41. Install upper screws securing lower shroud to steering column
    NOTE: 2x screws, T20, 1.5 Nm
    G00650870Courtesy of TESLA, INC.
  42. Align the clips then press downward to install upper shroud onto lower shroud
    NOTE: 4x clips
    G00650871Courtesy of TESLA, INC.
  43. Install main decor assembly
    NOTE: 15x clips, 1x center clip
    G00651102Courtesy of TESLA, INC.
  44. Install RH air wave bezel cap to main decor assembly
    NOTE: 2x clips
    G00651101Courtesy of TESLA, INC.
  45. Install LH air wave bezel cap to main decor assembly
    NOTE: 2x clips
    G00651100Courtesy of TESLA, INC.
  46. Align steering wheel to steering column then position it for installation
    NOTE: Steering wheel and column are keyed
    G00650872Courtesy of TESLA, INC.
    G00650873Courtesy of TESLA, INC.
  47. Install bolt securing steering wheel to steering column
    NOTE: 1x patch bolt, 10mm hex, 80 Nm, Install new patch bolt
    G00650874Courtesy of TESLA, INC.
  48. Connect steering wheel connector
    NOTE: 1x connector
    G00650875Courtesy of TESLA, INC.
  49. Connect driver air bag connector
    NOTE: 1x connector, 2x tabs, Make sure air bag harness doesn't get caught between driver air bag and horn mechanism
    G00650876Courtesy of TESLA, INC.
  50. Secure driver air bag assembly to steering wheel and verify it is fully engaged
    NOTE: 3x datums, 1x spring clip, Inspect to make sure lower horn bracket is properly secured to steering wheel before installing driver air bag
    G00650877Courtesy of TESLA, INC.
    G00650878Courtesy of TESLA, INC.
  51. Install center console onto vehicle
    NOTE: Recommend assistance, Tilt front of console downward, Slide assembly towards front of vehicle and tilt rear of console down into place
    G00650879Courtesy of TESLA, INC.
  52. Open front console rotating lid
    NOTE: Push down lightly to open
    G00651082Courtesy of TESLA, INC.
  53. Install console lid interior fasteners
    NOTE: 2x bolts, T20, 1.7 Nm, Top photo is early production vehicles, Bottom is for later production vehicles
    G00651088Courtesy of TESLA, INC.
    G00651089Courtesy of TESLA, INC.
  54. Install the phone dock tray with lower trim to the center console
    NOTE: 5x clips
    G00650880Courtesy of TESLA, INC.
  55. Install fasteners securing phone dock tray to center console
    NOTE: 2x screws, T20, 1 Nm, This step is only for early production vehicles
    G00651088Courtesy of TESLA, INC.
  56. Install charge cables into the USB ports
    NOTE: 2x cables
    G00651085Courtesy of TESLA, INC.
  57. Lower phone dock to original position
    G00650881Courtesy of TESLA, INC.
  58. Close rear console rotating lid
    G00651083Courtesy of TESLA, INC.
  59. Close front console rotating lid
    NOTE: This will avoid lid getting hung up on center display upon removal
    G00651082Courtesy of TESLA, INC.
  60. Install passenger knee air bag
    NOTE: 1x connector, Engage locking tab, Use caution not to damage connector/harness, Support air bag while connecting connector
    G00651079Courtesy of TESLA, INC.
  61. Install fasteners securing passenger knee air bag to vehicle
    NOTE: 4x patch bolts, E10, 8 Nm, 2x screws, T20, 2 Nm, 1x push clip, Install new patch bolts
    G00651076Courtesy of TESLA, INC.
    G00651077Courtesy of TESLA, INC.
    G00651078Courtesy of TESLA, INC.
  62. Install RH front exterior hardware to center console
    NOTE: 2x bolts, 10mm, 7 Nm
    G00651075Courtesy of TESLA, INC.
  63. nstall RH console side panel carpet
    NOTE: 12x clips, 2x locating pins, Position side panel and align the front locator, then the rear locator, Push side panel towards console to install
    G00651074Courtesy of TESLA, INC.
    G00650882Courtesy of TESLA, INC.
  64. Install RH front floor mat
    G00651072Courtesy of TESLA, INC.
  65. Connect the RH footwell assembly connectors
    NOTE: 2x connectors
    G00651071Courtesy of TESLA, INC.
  66. Install clips securing RH footwell assembly
    NOTE: 4x push clips
    G00651070Courtesy of TESLA, INC.
  67. Install RH lower A-pillar trim
    NOTE: 6x clips, 2x locating pins, Align front locating pin first
    G00650883Courtesy of TESLA, INC.
  68. Install clip securing RH lower A-pillar trim
    NOTE: 1x clip
    G00651068Courtesy of TESLA, INC.
  69. Install RH upper A-pillar trim
    NOTE: 3x clips, 1x tether, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
    G00650884Courtesy of TESLA, INC.
    G00650885Courtesy of TESLA, INC.
    G00651066Courtesy of TESLA, INC.
    G00650886Courtesy of TESLA, INC.
  70. Install RH mid A-pillar assembly
    NOTE: 1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Make sure the seal seat on top of the trim
    G00650887Courtesy of TESLA, INC.
  71. Install RH IP end cap
    NOTE: 3x clips
    G00650888Courtesy of TESLA, INC.
  72. Install driver knee air bag
    NOTE: 1x connector, Engage locking tab, Use caution not to damage connector/harness, Support air bag while connecting connector
    G00651059Courtesy of TESLA, INC.
    G00650889Courtesy of TESLA, INC.
  73. Install fasteners securing driver knee air bag to vehicle
    NOTE: 4x patch bolts, E10, 8 Nm, Install new patch bolts, 2x screws, T20, 2 Nm, 2x push clips
    G00650890Courtesy of TESLA, INC.
    G00650891Courtesy of TESLA, INC.
    G00650892Courtesy of TESLA, INC.
    G00650893Courtesy of TESLA, INC.
  74. Install LH front exterior hardware to center console
    NOTE: 2x bolts, 10mm, 7 Nm
    G00650894Courtesy of TESLA, INC.
  75. Install LH console side panel carpet
    NOTE: 11x clips, 2x locating pins, Position side panel and align the front into front locator, then the rear locator, Push side panel towards console to install
    G00651074Courtesy of TESLA, INC.
    G00650895Courtesy of TESLA, INC.
  76. Install LH console side panel carpet
    NOTE: 11x clips, 2x locating pins, Position side panel and align the front into front locator, then the rear locator, Push side panel towards console to install
    G00651074Courtesy of TESLA, INC.
    G00650895Courtesy of TESLA, INC.
  77. Install LH front floor mat
    G00650896Courtesy of TESLA, INC.
  78. Install connectors to LH footwell cover and position for installation
    NOTE: 3x tabs, 1x Ethernet connector, 1x puddle light connector
    G00650897Courtesy of TESLA, INC.
    G00650898Courtesy of TESLA, INC.
    G00650899Courtesy of TESLA, INC.
  79. Install screw and clips securing LH footwell cover
    NOTE: 1x screw, T20, 2.5 Nm, 2x push clips
    G00650900Courtesy of TESLA, INC.
  80. Install LH lower A-pillar trim
    NOTE: 6x clips, 2 locating pins, Align front locating pin first
    G00650901Courtesy of TESLA, INC.
  81. Install clip securing LH lower A-pillar trim
    NOTE: 1x push clip
    G00650902Courtesy of TESLA, INC.
  82. Reseat LH front door seal along lower A-pillar trim
    G00650903Courtesy of TESLA, INC.
  83. Install LH mid A-pillar assembly
    NOTE: 1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Pull seal over trim
    G00650904Courtesy of TESLA, INC.
  84. Install LH IP end cap
    NOTE: 3x clips
    G00650905Courtesy of TESLA, INC.
  85. Connect the First Responder Loop and 12V negative battery cable.
    G00650906Courtesy of TESLA, INC.
    G00650907Courtesy of TESLA, INC.
  86. Install the rear apron.
    G00650908Courtesy of TESLA, INC.
    G00650909Courtesy of TESLA, INC.
  87. Close the hood.
    G00650910Courtesy of TESLA, INC.
  88. Move LH front seat forward
    G00650911Courtesy of TESLA, INC.
  89. Move RH front seat forward
    G00650912Courtesy of TESLA, INC.
  90. Install RH rear exterior hardware to center console
    NOTE: 1x bolt, 10mm, 7 Nm
    G00650913Courtesy of TESLA, INC.
  91. Install LH rear exterior hardware to center console
    NOTE: 1x bolt, 10mm, 7 Nm
    G00650914Courtesy of TESLA, INC.
  92. Connect harness to rear of center console
    NOTE: 1x connector
    G00650915Courtesy of TESLA, INC.
  93. Install console lower rear panel
    NOTE: 5x clips
    G00650916Courtesy of TESLA, INC.
  94. Move the RH front seat to its original position.
  95. Move LH front seat to original position
    G00650917Courtesy of TESLA, INC.
  96. Raise all four windows
    G00650918Courtesy of TESLA, INC.
  97. Close all four doors
    NOTE: If 12V is powered up, Unlatch rear doors before closing
    G00651022Courtesy of TESLA, INC.
About FixVault