FixVault

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Accessory Drive Belt Tensioner Bolt/Nut
Bolt 51 (69)
Nut 21 (29)
A/C Compressor Bolt 18 (25)
Axle Shaft Nut 166 (225)
Ball Joint-To-Lower Control Arm Bolt/Nut 105 (142)
Camshaft Bearing Cap Bolt (1)
Camshaft Sprocket Bolt 40 (54)
Coolant Drain Union 14 (20)
Connecting Rod Bolt
Step 1 15 (20)
Step 2 Additional 90 Degrees
Crankshaft Pulley Bolt 102 (138)
Cylinder Head Bolt (2)
Step 1 36 (49)
Step 2 Additional 90 Degrees
Drive Belt Tensioner-To-Timing Chain Cover
Bolt 51 (69)
Nut 21 (29)
Drive Belt Idler Pulley 32 (43)
Drive Shaft Heat Insulator Bolt 13 (18)
Engine Coolant Temperature Sensor 15 (20)
Engine Hanger Bolt 28 (38)
Exhaust Manifold Nut 27 (37)
Exhaust Manifold Support Bracket Bolt 36 (49)
Exhaust Pipe 32 (43)
Flywheel/Drive Plate Bolt
A/T 65 (88)
M/T
Step 1 36 (49)
Step 2 Additional 90 Degrees
Front Exhaust Pipe-To-Center Exhaust Pipe Clamp Bolt 24 (33)
Front Exhaust Pipe-To-Exhaust Manifold Bolt 46 (62)
Front (Radiator Side) Engine Mount Bracket-To-Cylinder Block Bolt 57 (77)
Front (Radiator Side) Engine Mount Through-Bolt/Nut 69 (93)
Fuel Rail-To-Cylinder Head Bolt 14 (19)
Generator Mounting Bolt
Small Bolt 18 (24)
Large Bolt 40 (54)
Intake Manifold Bolt/Nut 22 (30)
Knock Sensor 29 (39)
Left Side Engine Mount 59 (80)
Left (Transaxle Side) Engine Mount Through-Bolt/Nut 64 (87)
Left (Transaxle Side) Engine Mount-To-Transaxle Bolt 48 (65)
Main Bearing Cap Subassembly-To-Cylinder Block Bolt
12-Point Bolt (3)
Step 1 16 (22)
Step 2 32 (43)
Step 3 Additional 45 Degrees
Step 4 Additional 45 Degrees
6-Point Bolt 14 (19)
Oil Control Valve Filter 22 (29)
Oil Filter Union 22 (30)
Oil Pan Drain Plug 27 (37)
Oxygen Sensor-To-Front Exhaust Pipe Nut 15 (20)
Rear Engine Mount-To-Transaxle Bolt 47 (64)
Rear Engine Mount Bracket-To-Cylinder Block Bolt 57 (77)
Rear Engine Mount Through-Bolt/Nut 69 (93)
Rear Suspension Member Bolts 59 (80)
Rear Suspension Upper Brace
Bolts 55 (74)
Nuts 59 (80)
Relief Valve Plug 27 (37)
Right Engine Mount Bracket-To-Timing Chain Cover Bolt 35 (47)
Right Engine Mount Insulator-To-Engine Mount Bracket 38 (52)
Support Bracket-To-Left (Transaxle Side) Engine Mount Bolt 15 (20)
Throttle Body Bolt/Nut 15 (20)
Timing Chain Cover Bolt/Nut & Stud Bolt (4)
Timing Chain Tensioner Slipper Bolt 14 (19)
Valve Timing Controller Assembly 40 (54)
Water Pump Bolt (5)
Wheel Lug Nut 76 (103)
INCH Lbs. (N.m) 
ABS Speed Sensor Bolt 71 (8)
Camshaft Position Sensor Bolt 80 (9)
Chain Tensioner-To-Timing Chain Cover Bolt 80 (9)
Clutch Release Cylinder Bolt 106 (12)
Coolant Bypass Pipe 80 (9)
Coolant Inlet Housing Nut 80 (9)
Crankshaft Position Sensor Bolt 80 (9)
Fuel Pipe Clamp-To-Cylinder Head Bolt 80 (9)
Heat Insulator-To-Exhaust Manifold Bolt 106 (12)
Ignition Coil-To-Cylinder Head Bolt/Nut 62 (7)
Oil Control Valve 80 (9.0)
Oil Pan Bolt/Nut 80 (9)
Oil Pressure Switch 80 (9)
Oil Pump Body Cover Screw 93 (10.5)
Oil Pump Pick-Up Tube Bolt/Nut 80 (9)
Oil Pump-To-Cylinder Block Bolt 80 (9)
Timing Chain Cover-To-Cylinder Head Bolts
10-mm Bolt 89 (10)
10-mm Nut 97 (11)
Stud 84 (9.5)
Timing Chain Cover-To-Cylinder Block Bolts
10-mm 97 (11)
12-mm (6)
Timing Chain Vibration Damper 80 (9)
Valve Cover Bolt/Nut (7)
With Washer 80 (9)
Without Washer 97 (11)
Water Bypass Pipe 80 (9)
(1) Tighten bolts to specification in sequence. See Fig 2. Tighten bolts on front camshaft bearing cap to 17 ft. lbs. (23 N.m). Tighten bolts for all other camshaft bearing caps to 115 INCH lbs. (13.0 N.m).
(2) Tighten bolts to specification in sequence. See Fig 3.
(3) Tighten bolts to specification in sequence. See Fig 4.
(4) Tighten all bolts with 12-mm head to 14 ft. lbs. (19 N.m). Tighten bolt "A" with 10-mm head to 115 INCH lbs. (13 N.m). See Fig 5. Tighten bolt "C" with 10-mm head to 80 INCH lbs. (9.0 N.m). Tighten all others to 97 INCH lbs. (11.0 N.m).
(5) Tighten bolt "B" to 97 INCH lbs. (11.0 N.m) and bolt "C" to 80 INCH lbs. (9.0 N.m). See Fig 5.
(6) Tighten to 14 Ft. Lbs (18.5 N.m).
(7) Tighten bolts to specification in sequence. See Fig 6.
Fig 1: Locating Cylinder Block, Crankshaft & Main Bearing Size Marks
G98D07786Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Fig 2: Identifying Camshaft Bearing Cap Bolt Removal & Installation Sequence
G98E07777Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Fig 3: Identifying Cylinder Head Bolt Removal & Installation Sequence
G98A07978Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Fig 4: Identifying Main Bearing Cap Bolt Removal & Installation Sequence
G98I07784Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Fig 5: Identifying Timing Chain Cover & Water Pump Bolt Location & Length
G98A11254Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Fig 6: Identifying Valve Cover Bolt/Nut Installation Sequence
G98B11222Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002