Front Seat (Bench Type): Reassembly

1. Connect the equalizing wire to the seat adjuster RH as shown in the illustration.
2. Tighten the adjusting nuts.

   HINT:

   When tighten the nuts, while holding one nuts, tighten the other.

3. Stake the claws.
   Fig 1: Installing Equalizing Wire To Seat Adjuster RH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Connect the equalizing wire to the seat adjuster LH as shown in the illustration.

Install the 2 spacers with the 2 bolts to the seat cushion frame.

Torque: 47 N.m (479 kgf.cm, 35 ft.lbf) 

Fig 2: Installing Equalizing Wire To Seat Adjuster LH

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the seat cushion cover with new hog rings to the seat cushion pad.

HINT:

When installing hog rings, take care to prevent wrinkles as little as possible.

1. Install the seat cushion frame to the seat cushion cover with pad.
   Fig 3: Installing Seat Cushion Cover with New Hog Rings

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the seat cushion frame with new hog rings and latch the seat cushion cover hooks.

   HINT:

   When installing hog rings, take care to prevent wrinkles as little as possible.

   Fig 4: Installing Seat Cushion Frame with New Hog Rings

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the cushion with the screw.

   HINT:

   Employ the same manner described above to the other side.

   Fig 5: Installing Cushion with Screw

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the seat cushion assembly with the 4 bolts to the seat adjusters.

Torque: 18 N.m (185 kgf.cm, 13 ft.lbf) 

1. Install the seatback frame to the seatback pad.
2. Install the seatback cover to the seatback pad with the frame.
   Fig 6: Installing Seat Cushion Assembly with 4 Bolts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the 4 headrest supports.

   HINT:

   Do not mistake the direction of the 2 LH headrest supports with the button.

4. Install the seatback cover with new hog rings to the seat-back pad.

   HINT:

   When installing hog rings, take care to prevent wrinkles as little as possible.

   Fig 7: Installing 4 Headrest Supports

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the armrest with the 2 nuts.
   Fig 8: Installing Armrest with 2 Nuts

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the new hog rings as shown in the illustration.

   HINT:

   When installing hog rings, take care to prevent wrinkles as little as possible.

   Fig 9: Installing New Hog Rings

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the seatback assembly with the 2 bolts.

   Torque: 39 N.m (400 kgf.cm, 29 ft.lbf) 

2. Install the nut to the rear side of the seat cushion.

   Torque: 18 N.m (185 kgf.cm, 13 ft.lbf) 

Install the seat cushion inner shield with the screw.

Fig 10: Installing Seat Cushion Inner Shield Screw

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install the seat cushion outer shield with the screw.

Check that the outer and inner tracks are locked at the same position.

If the sliding lock positions slip off, pull the sliding seat lever and slide the inner and outer tracks at the same sliding lock positions.

Fig 11: Installing Seat Cushion Outer Shield Screw

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002