Torque Specification
2AZ-FE
TORQUE SPECIFICATION - 2AZ-FE
| Part Tightened | N.m | kgf.cm | ft.lbf | |
|---|---|---|---|---|
| Engine mounting bracket No. 2 RH x Timing chain cover | 52 | 531 | 38 | |
| Engine moving control rod w/ bracket x Engine mounting bracket No. 2 RH | 64 | 653 | 47 | |
| Engine moving control rod w/ bracket x Fender apron RH | 64 | 653 | 47 | |
| Engine mounting stay No. 2 RH x Cylinder head | 64 | 653 | 47 | |
| Engine mounting stay No. 2 RH x Engine mounting bracket No. 2 RH | 64 | 653 | 47 | |
| Drain plug (A/T) | 49 | 500 | 36 | |
| Drain plug (M/T) | 49 | 500 | 36 | |
| Engine hanger No. 1 x Cylinder head | 38 | 387 | 28 | |
| Engine hanger No. 2 x Cylinder head | 38 | 387 | 28 | |
| ECT sensor x Cylinder head | 20 | 204 | 15 | |
| Knock sensor x Cylinder block | 39 | 398 | 29 | |
| Engine oil pressure switch assy x Cylinder head | 15 | 153 | 11 | |
| Water by-pass pipe No. 1 x Cylinder block | 9.0 | 92 | 80 in..lbf | |
| Transverse engine engine mounting bracket x Cylinder block | 54 | 551 | 40 | |
| Drive shaft bearing bracket x Cylinder block | 64 | 653 | 47 | |
| V-ribbed belt tensioner assy x Timing chain cover | 59.5 | 607 | 44 | |
| Ignition coil assy x Cylinder head | 9.0 | 92 | 80 in..lbf | |
| Water inlet x Cylinder block | 9.0 | 92 | 80 in..lbf | |
| Exhaust manifold converter x Cylinder head | 37 | 378 | 27 | |
| Exhaust manifold stay x Exhaust manifold converter | 44 | 449 | 32 | |
| Manifold converter insulator No. 1 x Exhaust manifold converter | 12 | 122 | 9 | |
| Oil level gage guide x Water by-pass pipe No. 1 | 9.0 | 92 | 80 in..lbf | |
| Intake manifold x Cylinder head | 30 | 306 | 22 | |
| Drive plate & ring gear (A/T) x Crankshaft | 98 | 1,000 | 72 | |
| Flywheel sub-assy (M/T) x Crankshaft | 130 | 1,330 | 96 | |
| Starter assy x Automatic transaxle assy | 39 | 398 | 29 | |
| Starter assy x Manual transaxle assy | 39 | 398 | 29 | |
| Engine mounting insulator LH x Automatic transaxle assy | 95 | 969 | 70 | |
| Engine mounting insulator LH x Manual transaxle assy | 143 | 1,459 | 105 | |
| Engine mounting insulator RH x Engine mounting bracket RH | 95 | 969 | 70 | |
| Engine mounting insulator FR x Engine mounting bracket FR | 87 | 888 | 64 | |
| Engine mounting bracket rear No. 2 x Engine lateral control rod (M/T) | 89 | 910 | 66 | |
| Vane pump assy x Timing chain cover | 43 | 439 | 32 | |
| Frame side plate x Front frame assy | Bolt A | 85 | 867 | 63 |
| Frame side plate x Body | Bolt B | 32 | 326 | 24 |
| Front suspension member brace rear x Front frame assy | Bolt C | 85 | 867 | 63 |
| Front suspension member brace rear x Body | Bolt D | 32 | 326 | 24 |
| Steering intermediate shaft | 35 | 357 | 26 | |
| Drive plate & ring gear x Torque converter | 41 | 418 | 30 | |
| Front suspension arm sub-assy lower No. 1 x Lower ball joint | 75 | 764 | 55 | |
| Tie rod assy x Steering knuckle | 49 | 500 | 36 | |
| Speed sensor front LH (w/ ABS) x Steering knuckle | 8.0 | 82 | 71 in..lbf | |
| Speed sensor front RH (w/ ABS) x Steering knuckle | 8.0 | 82 | 71 in..lbf | |
| Front axle hub LH nut x Front drive shaft | 294 | 3,000 | 217 | |
| Front stabilizer link assy x Front | suspension 74 | 755 | 55 | |
| Air cleaner assy x Body | 5.0 | 51 | 44 in..lbf | |
| Balanceshaft housing x Stiffening crankcase assy | 1st | 22 | 220 | 16 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Stiffening crankcase assy x Cylinder block | 33 | 332 | 24 | |
| w/ head taper screw plug No. 1 x Cylinder block | 26 | 265 | 19 | |
| Oil control valve filter x Cylinder block | 30 | 306 | 22 | |
| Cylinder block water drain cock x Stiffening crankcase assy | 25 | 255 | 18 | |
| Cylinder head x Cylinder block | 1st | 79 | 806 | 58 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Camshaft timing gear assy x Camshaft | 54 | 551 | 40 | |
| Camshaft timing sprocket x Camshaft | 54 | 551 | 40 | |
| Camshaft bearing cap No. 1 x Cylinder head | 30 | 301 | 22 | |
| Camshaft bearing cap No. 2 x Cylinder head | 30 | 301 | 22 | |
| Camshaft bearing cap No. 3 x Cylinder head | 9.0 | 92 | 80 in..lbf | |
| Oil pump assy x Stiffening crankcase assy | 19 | 194 | 14 | |
| Chain tensioner plate x Stiffening crankcase assy | 12 | 122 | 9 | |
| Oil pump drive sprocket x Oil pump | 30 | 301 | 22 | |
| Chain vibration damper No. 1 x Cylinder head | 9.0 | 92 | 80 in..lbf | |
| Chain vibration damper No. 1 x Cylinder block | 9.0 | 92 | 80 in..lbf | |
| Chain tensioner slipper x Cylinder block | 19 | 194 | 14 | |
| Timing chain guide x Crankshaft bearing cap No. 1 | 9.0 | 92 | 80 in..lbf | |
| Timing chain cover (See CHAIN (2AZ-FE)(FROM JULY, 2003) ) | Bolt A | 9.0 | 92 | 80 in..lbf |
| Bolt B | 21 | 214 | 15 | |
| Bolt C | 43 | 438 | 32 | |
| Nut | 9.0 | 92 | 80 in..lbf | |
| Oil pan x Stiffening crankcase assy | 9.0 | 92 | 80 in..lbf | |
| Oil pan drain plug x Oil pan | 25 | 250 | 18 | |
| Water pump assy x Cylinder block | 9.0 | 92 | 80 in..lbf | |
| Water pump pulley x Water pump assy | 26 | 265 | 19 | |
| Crankshaft position sensor x Timing chain cover | 9.0 | 92 | 80 in..lbf | |
| Crankshaft pulley x Crankshaft | 170 | 1,733 | 125 | |
| Chain tensioner assy No. 1 x Timing chain cover | 9.0 | 92 | 80 in..lbf | |
| Camshaft position sensor x Cylinder head | 9.0 | 92 | 80 in..lbf | |
| Cylinder head cover x Cylinder head | 11 | 110 | 8 | |
| Oil filter union x Stiffening crankcase assy | 30 | 306 | 22 | |
| Spark plug x Cylinder head | 19 | 194 | 14 | |
| Ventilation valve x Cylinder head cover | 19 | 194 | 14 | |
| Front suspension brace x Body | 80 | 816 | 59 | |
| Stud bolt (See OVERHAUL ) | Bolt A | 5 | 51 | 44 in..lbf |
| Bolt B | 5 | 51 | 44 in..lbf | |
| Bolt C | 10 | 97 | 84 in..lbf | |
| Bolt D | 10 | 97 | 84 in..lbf | |
| Stud bolt (See OVERHAUL ) Stud bolt A | Bolt A | 5.0 | 51 | 44 in..lbf |
| Bolt B | 10 | 97 | 84 in..lbf | |
| Bolt C | 5.0 | 51 | 44 in..lbf | |
| Crankshaft bearing cap x Cylinder block | 1st | 20 | 204 | 15 |
| 2nd | 40 | 408 | 29 | |
| Connecting rod cap x Connecting rod | 1st | 25 | 250 | 18 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
1MZ-FE/3MZ-FE
TORQUE SPECIFICATION - 1MZ-FE/3MZ-FE
| Part Tightened | N.m | kgf.cm | ft.lbf | |
| Engine hanger No. 2 x Cylinder head | 20 | 204 | 15 | |
| Knock sensor x Cylinder block 1MZ-FE | 1MZ-FE | 39 | 398 | 39 |
| 3MZ-FE | 20 | 204 | 15 | |
| Oil pressure switch assy x Cylinder block | 15 | 152 | 11 | |
| Compressor mounting bracket No.1 x Cylinder block | 25 | 255 | 18 | |
| Generator bracket No. 1 x Cylinder block | 58 | 591 | 43 | |
| Pump bracket x Cylinder head | 32 | 326 | 24 | |
| Drive shaft bearing bracket x Cylinder block | 64 | 653 | 47 | |
| Exhaust manifold converter sub-assy No. 2 x Cylinder head | 49 | 500 | 36 | |
| Exhaust manifold heat insulator No. 2 x Cylinder head | 8.5 | 87 | 75 in..lbf | |
| Exhaust manifold converter sub-assy RH x Cylinder head | 49 | 500 | 36 | |
| Intake manifold x Cylinder head | 15 | 153 | 11 | |
| Ignition coil assy x Cylinder head cover | 8.0 | 82 | 71 in..lbf | |
| Intake air surge tank x Intake manifold | 28 | 286 | 21 | |
| Surge tank stay bolt | 20 | 204 | 15 | |
| Engine hanger No. 2 x Cylinder head | 39 | 398 | 29 | |
| Engine hanger No. 1 x Intake air surge tank | 39 | 398 | 29 | |
| Manifold stay No. 2 x Exhaust manifold converter sub-assy | 49 | 500 | 36 | |
| Manifold stay No. 2 x Automatic transaxle assy | 49 | 500 | 36 | |
| Engine mounting insulator RH x Engine mounting bracket | 95 | 969 | 70 | |
| Engine mounting insulator LH x Automatic transaxle assy | 95 | 969 | 70 | |
| Engine mounting insulator FR x Automatic transaxle assy | 87 | 887 | 64 | |
| Vane pump assy x Pump bracket | 43 | 439 | 32 | |
| Vane pump assy x Engine mounting bracket | 43 | 439 | 32 | |
| Frame side rail plate sub-assembly x Front frame assy | ||||
| (See REPLACEMENT ) | Bolt A | 85 | 867 | 63 |
| Bolt B | 32 | 326 | 24 | |
| Nut | 32 | 326 | 24 | |
| Front suspension member brace rear x Front frame assy | ||||
| (See REPLACEMENT ) | ||||
| (See REPLACEMENT ) | Bolt A | 85 | 867 | 63 |
| Bolt B | 32 | 326 | 24 | |
| Nut | 32 | 326 | 24 | |
| Compressor and magnetic clutch x Compressor mounting bracket No.1 | ||||
| (See REPLACEMENT ) | Bolt | 25 | 250 | 18 |
| Nut | 26 | 260 | 19 | |
| Generator belt adjusting bar x Cylinder block | ||||
| (See REPLACEMENT ) | Nut A | 43 | 438 | 32 |
| Bolt B | 18 | 184 | 13 | |
| Bolt C | 8.0 | 82 | 71 in..lbf | |
| Generator bracket No. 2 x Transverse engine engine mounting bracket | 28 | 286 | 21 | |
| Intermediate shaft sub-assy | 35 | 357 | 26 | |
| Drive plate & ring gear x Torque converter | 41 | 418 | 30 | |
| Flywheel housing under cover x Automatic transaxle assy | 7.8 | 80 | 69 in..lbf | |
| Front suspension arm x Lower ball joint | 75 | 764 | 55 | |
| Tie rod end x Steering knuckle | 49 | 500 | 36 | |
| Front axle hub nut x Front drive shaft | 294 | 2,998 | 217 | |
| Front stabilizer link assy x Front suspension | 74 | 755 | 55 | |
| V-bank cover x Cylinder head cover | 7.9 | 81 | 70 in..lbf | |
| Engine mounting stay No. 2 RH x Engine engine mounting bracket | 64 | 653 | 47 | |
| Engine moving control rod (See REPLACEMENT ) | Bolt A | 64 | 653 | 47 |
| Bolt B | 23 | 235 | 17 | |
| Camshaft sub-gear x Main gear | 5.4 | 55 | 48 in..lbf | |
| Engine rear oil seal retainer x Cylinder block | 8.0 | 82 | 71 in..lbf | |
| Oil pump assy x Cylinder block (See OVERHAUL ) | 10 mm head | 8.0 | 82 | 71 in..lbf |
| 12 mm head | 20 | 204 | 15 | |
| 14 mm head | 43 | 439 | 32 | |
| Crank position sensor x Oil pump assy | 8.0 | 82 | 71 in..lbf | |
| Oil pan baffle plate x Oil pan sub-assy | 8.0 | 82 | 71 in..lbf | |
| Oil pan sub-assy x Cylinder block (See OVERHAUL ) | 10 mm head | 8.0 | 82 | 71 in..lbf |
| 12 mm head | 20 | 204 | 15 | |
| Oil strainer sub-assy x Oil pan sub-assy | 8.0 | 82 | 71 in..lbf | |
| Oil pan sub-assy No. 2 x Oil pan sub-assy | 8.0 | 82 | 71 in..lbf | |
| Oil pan drain plug x Oil pan sub-assy No. 2 | 45 | 459 | 33 | |
| Water inlet housing x Cylinder block | 8.0 | 82 | 71 in..lbf | |
| Cylinder head x Cylinder block | 12 pointed head 1st | 54 | 551 | 40 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Recessed head | 19 | 189 | 14 | |
| Camshaft bearing cap x Cylinder head | 16 | 163 | 12 | |
| Timing belt plate x Oil pump assy | 8.0 | 82 | 71 in..lbf | |
| Water pump assy x Cylinder block | 8.0 | 82 | 71 in..lbf | |
| Oil level gage guide x Cylinder block | 8.0 | 82 | 71 in..lbf | |
| Oil filter union x Cylinder block | 30 | 306 | 22 | |
| Timing belt idler bracket x Cylinder block | 28 | 286 | 21 | |
| Timing belt No. 3 cover x Cylinder head | 8.5 | 87 | 76 in..lbf | |
| Camshaft timing pulley x Camshaft | 125 | 1,275 | 92 | |
| Timing belt idler sub-assy No. 2 x Timing belt idler bracket | 43 | 438 | 32 | |
| Timing belt idler sub-assy No. 1 x Cylinder block | 34 | 347 | 25 | |
| Chain tensioner assy No. 1 x Oil pump assy | 27 | 280 | 20 | |
| Transverse engine engine mounting bracket x Cylinder block | 28 | 286 | 21 | |
| Timing belt No. 2 cover x Timing belt No. 3 cover | 8.5 | 87 | 76 in..lbf | |
| Timing belt No. 1 cover x Oil pump assy | 8.5 | 87 | 76 in..lbf | |
| Crankshaft pulley x Crankshaft | 215 | 2,192 | 159 | |
| Camshaft position sensor x Cylinder head | 8.0 | 82 | 71 in..lbf | |
| Cylinder head cover x Cylinder head | 8.0 | 82 | 71 in..lbf | |
| Spark plug x Cylinder head | 18 | 184 | 13 | |
| Vane pump assy x Adjusting strut | 43 | 439 | 32 | |
| Generator x Generator bracket | 58 | 591 | 43 | |
| Generator x Adjusting bar | 18 | 184 | 13 | |
| Front suspension brace upper x Body | 80 | 816 | 59 | |
| Water outlet x Cylinder head | 15 | 153 | 11 | |
| Exhaust manifold heat insulator No. 2 x Exhaust manifold LH | 8.5 | 87 | 55 in..lbf | |
| Exhaust pipe support bracket No. 1 x Automatic transaxle assy | 21 | 214 | 15 | |
| Drive plate & ring gear sub-assy x Crankshaft | 83 | 846 | 61 | |
| w/ head straight screw plug No. 1 x Cylinder head | 44 | 449 | 32 | |
| w/ head straight screw plug No. 2 x Cylinder head | 44 | 449 | 32 | |
| Main bearing cap x Cylinder block | 12 pointed head 1st | 22 | 224 | 16 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| 6 pointed head | 27 | 275 | 20 | |
| Connecting rod cap x Connecting rod | 1st | 25 | 250 | 18 |
| 2nd | Turn 90° | Turn 90° | Turn 90° | |
| Cylinder block w/ head straight screw No. 1 plug x Cylinder block | 30 | 306 | 22 | |
| Cylinder block w/ head straight screw No. 2 plug x Cylinder block | 50 | 510 | 37 | |
| Cylinder block w/head straight screw No. 3 plug x Cylinder block | 30 | 306 | 22 | |
| Water seal plate x Cylinder block | 18 | 184 | 13 | |
| Cylinder block water drain cock sub-assy x Cylinder block | 39 | 398 | 29 | |