FixVault
Home › Toyota › 2007 › 4Runner Limited, 4.0 U, 4WD › Repair and Diagnosis › Engine Performance › Engine Control System (1GR-FE) › SFI System › VC Output Circuit › Inspection Procedure

Inspection Procedure

  1. CHECK MIL 
    1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.

      OK: MIL lights up 

    OK: SYSTEM OK 

    NG: GO TO NEXT STEP 

  2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM 
    1. Connect an intelligent tester to the DLC3.
    2. Turn the ignition switch ON and turn the tester ON.
    3. Check the communication between an intelligent tester and ECM.

      Result 

      RESULT CHART

      Result Proceed to
      Communication Is possible A
      Communication is not possible B

    A: GO TO  MIL CIRCUIT 

    B: GO TO NEXT STEP 

  3. CHECK MIL (THROTTLE BODY) 
    1. Disconnect the throttle body connector.
    2. Turn the ignition switch ON.
    3. Check the MIL. Result
      RESULT CHART

      Result Proceed to
      MIL Illuminates A
      MIL does not Illuminate B
    4. Reconnect the throttle body connector.

    A: REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY 

    B: GO TO NEXT STEP 

  4. CHECK MIL (ACCELERATOR PEDAL) 
    1. Disconnect the accelerator pedal connector.
    2. Turn the ignition switch ON.
    3. Check the MIL.

      Result 

      RESULT CHART

      Result Proceed to
      MIL illuminates A
      MIL does not Illuminate B
    4. Reconnect the accelerator pedal connector.

    A: REPLACE ACCELERATOR PEDAL ROD ASSEMBLY 

    B: GO TO NEXT STEP 

  5. CHECK MIL (CANISTER PUMP MODULE) 
    1. Disconnect the canister pump module connector.
    2. Turn the ignition switch ON.
    3. Check the MIL

      Result 

      RESULT CHART

      Result Proceed to
      MIL illuminates A
      MIL does not illuminate B
    4. Reconnect the canister pump module connector.

    A: REPLACE CHARCOAL CANISTER ASSEMBLY 

    B: GO TO NEXT STEP 

  6. CHECK MIL (VVT SENSOR FOR BANK 1) 
    1. Disconnect the VVT sensor (bank 1) connector.
    2. Turn the ignition switch ON.
    3. Check the MIL.

      Result 

      RESULT CHART

      Result Proceed to
      MIL illuminates A
      MIL does not illuminate B
    4. Reconnect the VVT sensor (bank 1) connector.

    A: REPLACE WT SENSOR FOR BANK 1 

    B: GO TO NEXT STEP 

  7. CHECK MIL (VVT SENSOR FOR BANK 2) 
    1. Disconnect the VVT sensor (bank 2) connector.
    2. Turn the ignition switch ON.
    3. Check the MIL.

      Result 

      RESULT CHART

      Result Proceed to
      MIL illuminates A
      MIL does not illuminate B
    4. Reconnect the VVT sensor (bank 2) connector.

    A: REPLACE VVT SENSOR FOR BANK 2 

    B: GO TO NEXT STEP 

  8. CHECK HARNESS AND CONNECTOR (VC OUTPUT CIRCUIT) 
    1. Disconnect the throttle body connector.
    2. Disconnect the accelerator pedal connector.
    3. Disconnect the canister pump module connector.
    4. Disconnect the VVT sensor (bank 1) connector.
    5. Disconnect the VVT sensor (bank 2) connector.
    6. Disconnect the ECM connector.
      Fig 1: Checking Harness And Connector (VC Output Circuit)
      G04968602Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
    7. Check the resistance.

      Standard Resistance (Check for short) 

      TESTER CONNECTIONS SPECIFIED CONDITIONS

      Tester Connections Specified Conditions
      VC(E4-23)-Body ground 10 kΩ or higher
      VCPA (E8-26) - Body ground
      VCP2 (E8-27) - Body ground
    8. Reconnect the throttle body connector.
    9. Reconnect the accelerator pedal connector.
    10. Reconnect the canister pump module connector.
    11. Reconnect the VVT sensor (bank 1) connector.
    12. Reconnect the VVT sensor (bank 2) connector.
    13. Reconnect the ECM connector.

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: REPLACE ECM 

About FixVault