FixVault
Home › Toyota › 2007 › Yaris Base, 2D Hatchback, Automatic › Repair and Diagnosis › External Pages › Different car › Section 34 (Body Control System) › BCM (Body Control Module) › Configuration › Write Configuration Procedure

Write Configuration Procedure

WARNING: This page is about a different car, the 2007 Nissan Versa. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION: If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be detected in self-diagnosis depending on control unit which carries out CAN communication.
  1. With ignition switch OFF, connect CONSULT-II and CONSULT-II CONVERTER to data link connector and turn ignition switch ON.
    Fig 1: Connecting CONSULT-II And CONSULT-II Converter To Data Link Connector
    G04811544
  2. Touch "START (NISSAN BASED VHCL)".
    Fig 2: CONSULT-II Function Screen Display - START (NISSAN BASED VHCL)
    G04811545
  3. Touch "BCM" on "SELECT ITEM" screen. If "BCM" is not indicated, go to GENERAL INFORMATION section to check CONSULT II data link connector (DLC) circuit. Refer to " CONSULT-II DATA LINK CONNECTOR (DLC) CIRCUIT  "  .
    Fig 3: CONSULT-II Function Screen Display - Select System
    G04811546
  4. Touch "BCM" on "SELECT TEST ITEM" screen.
    Fig 4: CONSULT-II Function Screen Display - SELECT TEST ITEM
    G04815645
  5. Touch "CONFIGURATION" on "SELECT DIAG MODE" screen.
    Fig 5: CONSULT-II Function Screen Display - SELECT DIAG MODE
    G04811547
  6. Touch "C11 (SPEC1)" and "OK" on "VEHICLE SELECT" screen. For canceling, touch "CANCEL" on "VEHICLE SELECT" screen.
    NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to " MODEL VARIATION  "  .
    Fig 6: CONSULT-II Function Screen Display - SELECT DIAG MODE
    G04815647
  7. Touch "WRITE CONFIGURATION" on "SELECT CONFIG ITEM" screen.
    Fig 7: CONSULT-II Function Screen Display - SELECT CONFIG ITEM
    G04815648
  8. Touch "YES".

    For canceling, touch "NO".

    Fig 8: CONSULT-II Function Screen Display - CONFIGURATION
    G04815658
  9. Using the following flow chart, identify the correct model and configuration list. Confirm and/or change setting value for each item according to the configuration list.

    Depending on CONSULT-II software version being used, some or all of the write configuration items shown in the following configuration lists may be displayed. If an item does not appear on the CONSULT-II "WRITE CONFIGURATION" screen(s), then it is an auto setting item and it cannot be manually set or changed.

    NOTE: Confirm vehicle model on IDENTIFICATION PLATE. Refer to " MODEL VARIATION  "  .
    MODEL VARIATION CHART

    ITEM SET VAL
    KEYLESS ENTRY WITH <=> WITHOUT
    I-KEY WITH <=> WITHOUT
    DTRL WITH <=> WITHOUT
    THEFT ALARM WITH <=> WITHOUT
  10. Touch "CHNG SETTING" on "WRITE CONFIGURATION" screen.
    CAUTION: Make sure to touch "CHNG SETTING" even if the indicated configuration of brand-new BCM is same as the desirable configuration.
    If not, configuration which is set automatically by selecting vehicle model cannot be memorized.
  11. Touch "OK" on "WRITE CONFIGURATION" screen.

    If "CANCEL" is touched, it will return to previous screen.

    Fig 9: CONSULT-II Function Screen Display - WRITE CONFIGURATION
    G04815659
  12. Wait until the next screen during setting.
    Fig 10: CONSULT-II Function Screen Display - WRITE CONFIGURATION
    G04815660
  13. WRITE CONFIGURATION results are printed out automatically. Confirm "WRITE CONFIGURATION" is correctly executed by comparing sheet automatically printed out with applicable configuration list shown in step  9.
    Fig 11: CONSULT-II Function Screen Display - WRITE CONFIGURATION
    G04815661
  14. Touch "OK" on "WRITE CONFIGURATION" screen. WRITE CONFIGURATION is completed.
    Fig 12: CONSULT-II Function Screen Display - WRITE CONFIGURATION
    G04815662
About FixVault