Rear Speed Sensor: Installation

HINT:

• Use the same procedure for the LH side and RH side.
• The following procedure is for the LH side.
• If the sensor rotor needs to be replaced, replace it together with the outboard joint shaft assembly.

  (See INSTALLATION )

  Fig 1: Locating Rear Speed Sensor With Bolt

  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. INSTALL REAR SPEED SENSOR 
   1. Install the rear speed sensor with the bolt.

      Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf) 

      NOTE: Keep the rear speed sensor tip and sensor installation hole free from foreign matter.
      Fig 2: Locating Rear Speed Sensor With Bolt

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   2. Install the No. 1 clamp and No. 2 clamp with the 2 bolts.

      Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

      Fig 3: Locating No. 1 And No. 2 Clamp With Bolts

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: Do not twist the rear speed sensor wire when installing the clamp.
   3. Insert the connector and grommet to the inside of the vehicle through the hole in the wheel well.
      NOTE: Make sure that the grommet's band clamp remains on the outside of the vehicle.
   4. Hold the grommet and pull it from the inside of the vehicle to the outside of the vehicle. Then, secure it in place so that it is not tilted.
      NOTE: When pulling out the grommet, do not grip the sensor wire.
   5. Connect the rear speed sensor connector.
   Fig 4: Locating Rear Speed Sensor Connector
   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH  (See INSTALLATION )
3. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH  (See INSTALLATION )
4. INSTALL FRONT DECK SIDE TRIM COVER LH  (See INSTALLATION )
5. INSTALL NO. 2 DECK SIDE TRIM HOOK  (See INSTALLATION )
6. INSTALL ROPE HOOK ASSEMBLY (for LH Side)  (See INSTALLATION )
7. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)  (See INSTALLATION )
8. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)  (See INSTALLATION )
9. INSTALL REAR POWER OUTLET SOCKET COVER  (See INSTALLATION )
10. INSTALL REAR POWER POINT SOCKET ASSEMBLY  (See INSTALLATION )
11. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH  (See INSTALLATION )
12. INSTALL SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)  (See INSTALLATION )
13. INSTALL POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)  (See INSTALLATION )
14. INSTALL DECK SIDE TRIM LH  (See INSTALLATION )
15. INSTALL DECK SIDE TRIM COVER LH  (See INSTALLATION )
16. INSTALL REAR FLOOR FINISH PLATE  (See INSTALLATION )
17. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)  (See INSTALLATION )
18. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)  (See INSTALLATION )
19. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)  (See INSTALLATION )
20. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)  (See INSTALLATION )
21. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)  (See INSTALLATION )
22. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)  (See INSTALLATION )
23. INSTALL REAR MAT  (See INSTALLATION )
24. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)  (See INSTALLATION )
25. INSTALL DECK SIDE TRIM BOX LH  (See INSTALLATION )
26. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)  (See INSTALLATION )
27. INSTALL DECK SIDE TRIM BOX RH  (See INSTALLATION )
28. INSTALL JACK CARRIER ASSEMBLY  (See INSTALLATION )
29. INSTALL JACK ASSEMBLY  (See INSTALLATION )
30. INSTALL JACK CARRIER CUSHION  (See INSTALLATION )
31. INSTALL JACK CARRIER SUPPORT 
32. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)  (See INSTALLATION )
33. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)  (See INSTALLATION )
34. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)  (See INSTALLATION )
35. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY  (See INSTALLATION )
36. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY  (See INSTALLATION )
37. INSTALL DECK BOARD ASSEMBLY  (See INSTALLATION )
38. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH  (See INSTALLATION )
39. INSTALL REAR DOOR SCUFF PLATE LH  (See INSTALLATION )
40. INSTALL SERVICE PLUG GRIP  (See INSTALLATION )
41. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
42. CHECK FOR SPEED SENSOR SIGNAL 

    HINT:

    (See TEST MODE PROCEDURE )