Inspection Procedure

1. Disconnect the G7 connector.
2. Measure the voltage according to the value(s) in the table below.

   Standard voltage 

   VOLTAGE SPECIFICATION TABLE
   
   

   Tester Connection	Condition	Specified Condition
   G7-3 (B) - Body ground	Ignition switch on (IG)	11 to 14 V

   Fig 1: Identifying Power Window Switch Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step. 

1. Measure the resistance when the switch is operated according to the value(s) in the table below.

   Standard resistance 

   RESISTANCE SPECIFICATION TABLE
   
   

   Tester Connection	Switch Condition	Specified Condition
   1 (D) - 2 (SD)	UP	Below 1 Ω
   3 (B) - 4 (U)		Below 1 Ω
   1 (D) - 2 (SD)	OFF	Below 1 Ω
   4 (U) - 5 (SU)		Below 1 Ω
   4 (U) - 5 (SU)	DOWN	Below 1 Ω
   1 (D) - 3 (B)		Below 1 Ω

   Fig 2: Identifying Power Window Switch Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPLACE POWER WINDOW SWITCH (FRONT PASSENGER SIDE)  (See REMOVAL  )

OK: Go to next step. 

1. Disconnect the G7 and G1 connectors.
2. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   RESISTANCE SPECIFICATION TABLE
   
   

   Tester Connection	Condition	Specified Condition
   G7-4 (U) - G1-2 (U)	Always	Below 1 Ω
   G7-1 (D) - G1-1 (D)	Always	Below 1 Ω
   G7-4 (U) - Body ground	Always	10 kΩ or higher
   G7-1 (D) - Body ground	Always	10 kΩ or higher

   Fig 3: Identifying Power Window Switch & Power Window Regulator Motor Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next step. 

1. Check power window regulator motor operation.
   1. Remove the power window regulator motor. (See REMOVAL  )
   2. Apply battery voltage to the motor connector according to the table below.
      NOTE: Do not apply battery voltage to any terminals except terminals 1 and 2.

      OK 

      MEASUREMENT CONDITION AND SPECIFIED CONDITION TABLE
      
      

      Measurement Condition	Specified Condition
      Battery negative (-) → Terminal 2 Battery positive (+) → Terminal 1	Motor gear rotates clockwise
      Battery negative (-) → Terminal 1 Battery positive (+) → Terminal 2	Motor gear rotates counterclockwise

2. Check PTC operation:
   Fig 4: Identifying Power Window Regulator Motor Assembly (Front Passenger Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   NOTE: The work must be performed with the power window regulator and door glass installed on the vehicle.
   1. Install the power window regulator motor. (See INSTALLATION  )
   2. Connect an electrical tester DC 400 A probe to the wire harness of terminal 2.
      NOTE: Match the arrow mark of the probe with the direction of the current flow.
   3. Fully close the door glass by pressing the power window UP switch. Wait for approximately 60 seconds.
   4. Continue to press the power window UP switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (Inspection of current shut-off).

      Standard: 4 to 90 seconds 

   5. 60 seconds after the previous step, press the power window DOWN switch (passenger side).
      Fig 5: Identifying Power Window Regulator Motor Connector Terminals

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK: The passenger side window goes down. 

NG: REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER SIDE)  (See REMOVAL  )

OK: Go to next step. 

1. Disconnect the M1 and G7 connectors.
2. Measure the resistance according to the value(s) in the table below.

   Standard resistance 

   RESISTANCE SPECIFICATION TABLE
   
   

   Tester Connection	Condition	Specified Condition
   M1-16 (U) - G7-5 (SU)	Always	Below 1 Ω
   M1-15 (D) - G7-2 (SD)	Always	Below 1 Ω
   M1-16 (U) - Body ground	Always	10 kΩ or higher
   M1-15 (D) - Body ground	Always	10 kΩ or higher

   Fig 6: Identifying Power Window Master Switch & Power Window Switch Connector Terminals

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: REPLACE POWER WINDOW MASTER SWITCH  (See REMOVAL  )