FixVault
Home › Toyota › 2009 › 4Runner Limited, 4.7 T, AWD › Repair and Diagnosis › Body & Frame › Windows › Windshield/Window Glass › Power Window Control System › Data List/Active Test

Data List/Active Test

  1. DATA LIST 

    HINT:

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch ON.
    3. Turn the Techstream on.
    4. Enter the following menus:
      1. Select: Body Electrical/(desired system)/Data List.
    5. According to the display on the Techstream, read the Data List.

      Back Door: 

      NORMAL CONDITION REFERENCE CHART

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Wiper Turn Position SW Rear wiper turn position switch signal/ON or OFF ON: Rear wiper turn position switch is in ON position
      OFF: Rear wiper turn position switch is in OFF position      		 -
      Wiper Retracting SW Rear wiper retract switch signal/ON or OFF ON: Rear wiper retract switch is in ON position
      OFF: Rear wiper retract switch is in OFF position      		 -
      Door Key Linked Unlock SW Back door key lock and unlock switch signal/ON or OFF ON: Back door lock key cylinder is turned to unlock
      OFF: Key is in back door lock key cylinder (original position)      		 -
      Door Key Linked Lock SW Back door key lock and unlock switch signal/ON or OFF ON: Back door lock key cylinder is turned to unlock
      OFF: Key is in back door lock key cylinder (original position)      		 -
      Closer Position SW Closer position switch signal/ON or OFF ON: Closer position switch is in ON position
      OFF: Closer position switch is in OFF position      		 -
      Power Window Position Back door glass position signal/CLOSE or OPEN CLOSE: Back door glass is in CLOSE position
      OPEN: Back door glass is in OPEN position      		 -
      Glass Position (Close-1/4) Door glass position (Fully closed - 1/4 open) signal/OK or CAUTION OK: Power window is going UP by manual operation
      CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position
      		 -
      Glass Position (1/4-2/4) Door glass position (1/4 open - 2/4 open) signal/OK or CAUTION OK: Power window is going UP by manual operation
      CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position
      		 -
      Glass Position (2/4-3/4) Door glass position (2/4 open - 3/4 open) signal/OK or CAUTION OK: Power window is going UP by manual operation
      CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position
      		 -
      Glass Position (3/4-Open) Door glass position (3/4 open - Fully open) signal/OK or CAUTION OK: Power window is going UP by manual operation
      CAUTION: CAUTION may be displayed when resistance is applied in each position. In this case, there must be a foreign object stuck in that position
      		 -
      Number of Trouble Codes Number of diagnosis codes/Min.: 0, Max.: 255 Number of DTCs will be displayed -

      Body: 

      NORMAL CONDITION REFERENCE CHART

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      IG SW Ignition switch signal/ON or OFF ON: Power source mode is on (IG)
      OFF: Power source mode is off or on (ACC)      		 -
      D Door Courtesy SW Driver side door courtesy switch signal/ON or OFF ON: Driver side door is open
      OFF: Driver side door is closed      		 -
      P Door Courtesy SW Front passenger side door courtesy switch signal/ON or OFF ON: Front passenger side door is open
      OFF: Front passenger side door is closed      		 -
  2. ACTIVE TEST 
    NOTE: When a Rear Junction Block ECU and Multiplex Network Front Light ECU (Front Controller) related vehicle switch is ON, Active Test items related to the vehicle switch are prohibited (double operation prohibition). Check that the vehicle switches are OFF before performing Active Tests.

    HINT:

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch ON.
    3. Turn the Techstream on.
    4. Enter the following menus:
      1. Select: Body Electrical/Back Door/Active Test.
    5. According to the display on the Techstream, perform the Active Test.

      Back Door 

      TESTER DISPLAY REFERENCE CHART

      Tester Display Test Part Control Range Diagnostic Note
      Power Window Back door power window UP/DOWN (OFF) -
About FixVault