Data List / Active Test

READ DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.

Check the values by referring to the table below.

Tilt & Telescopic

TILT & TELESCOPIC - DATA LIST

Tester Display	Measurement Item/Range	Normal Condition
Tilt Position	Current tilt position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Telesco Position	Current telescopic position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Tilt Return Position	Memorized tilt return position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Telesco Return Position	Memorized telescopic return position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Tilt Memory Pos 1	Tilt data of memory position 1/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Telesco Memory Pos 1	Telescopic data of memory position 1/ min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Tilt Memory Pos 2	Tilt data of memory position 2/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Telesco Memory Pos 2	Telescopic data of memory position 2/ min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Tilt Memory Pos 3	Tilt data of memory position 3/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Telesco Memory Pos 3	Telescopic data of memory position 3/ min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Tilt Up Limit	Uppermost tilt position/Not Mem or Mem	Not Mem: Position not memorized Mem: Position memorized
Tilt Up Limit Position	Uppermost tilt position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Tilt Down Limit	Lowermost tilt position/Not Mem or Mem	Not Mem: Position not memorized Mem: Position memorized
Tilt Down Limit Position	Lowermost tilt position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Telesco Short Limit	Shortest telescopic position/Not Mem or Mem	Not Mem: Position not memorized Mem: Position memorized
Telesco Short Limit Pos	Shortest telescopic position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Telesco Long Limit	Longest telescopic position/Not Mem or Mem	Not Mem: Position not memorized Mem: Position memorized
Telesco Long Limit Pos	Longest telescopic position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)	7000 to 9000 H (28672 to 36864 edges)
Tilt Up Switch	Input state of tilt up by manual switch/ ON or OFF	ON: Tilt up activated by manual switch OFF: Tilt up not activated by manual switch
Tilt Up SW (CAN)	Input state of tilt up by manual switch/ ON or OFF	ON: Tilt up activated by manual switch OFF: Tilt up not activated by manual switch
Tilt Down Switch	Input state of tilt down by manual switch/ON or OFF	ON: Tilt down activated by manual switch OFF: Tilt down not activated by manual switch
Tilt Down SW (CAN)	Input state of tilt down by manual switch/ON or OFF	ON: Tilt down activated by manual switch OFF: Tilt down not activated by manual switch
Telesco Short Switch	Input state of telescopic short by manual switch/ON or OFF	ON: Telescopic short activated by manual switch OFF: Telescopic short not activated by manual switch
Telesco Short SW (CAN)	Input state of telescopic short by manual switch/ON or OFF	ON: Telescopic short activated by manual switch OFF: Telescopic short not activated by manual switch
Telesco Long Switch	Input state of telescopic long by manual switch/ON or OFF	ON: Telescopic long activated by manual switch OFF: Telescopic long not activated by manual switch
Telesco Long SW (CAN)	Input state of telescopic long by manual switch/ON or OFF	ON: Telescopic long activated by manual switch OFF: Telescopic long not activated by manual switch
T&T Manual SW Data	Voltage data of manual switch/min.: 0 V, max.: 5 V	Neutral position: Below 0.2 V Tilt up: 1.67 to 2.13 V Tilt down: 0.54 to 0.74 V Telescopic contract: 1.08 to 1.40 V Telescopic extend: 2.22 to 2.77 V
S/B Mem 1	Tilt and telescopic memory position 1/ Not Mem or Mem	Not Mem: Position not memorized Mem: Position memorized
S/B Mem 2	Tilt and telescopic memory position 2/ Not Mem or Mem	Not Mem: Position not memorized Mem: Position memorized
S/B Mem 3	Tilt and telescopic memory position 3/ Not Mem or Mem	Not Mem: Position not memorized Mem: Position memorized
T&T Autoaway Function	Auto away/return function/ON or OFF	ON: Auto away/return function allowed OFF: Auto away/return function prohibited
Power Source Voltage	Voltage data of power supply/min.: 0 V, max.: 20 V	Actual power supply voltage 11 to 14 V
Freeze Speed Info	Vehicle speed data/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)	Actual vehicle speed
IG Switch(CAN)	Communication state of engine switch/ ON or OFF	ON: Communication normal OFF: Communication interrupted
IG Switch	Input state of engine switch/ON or OFF	ON: Input signal normal OFF: Input signal interrupted
Key Code Confirm(CAN)	Communication state of key code confirmation signal/ON or OFF	ON: Communication normal OFF: Communication interrupted
Receive from Meter	Communication state of combination meter signal/OK or Interruption	OK: Communication normal Interruption: Communication interrupted
Receive from Seat ECU	Communication state of position control ECU signal/OK or Interruption	OK: Communication normal Interruption: Communication interrupted
Receive from Combi	Communication state of combination switch ECU signal/OK or Interruption	OK: Communication normal Interruption: Communication interrupted
J/B	Communication state of main body ECU signal/OK or Interruption	OK: Communication normal Interruption: Communication interrupted
B/B	Communication state of optional after parts ECU signal/OK or Interruption	OK: Communication normal Interruption: Communication interrupted
The Number of DTCs	Number of diagnostic trouble codes / min.: 0, max.: 255	Actual number of diagnostic trouble codes

PERFORM ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.

Check the values by referring to the table below.

Tilt & Telescopic

TILT & TELESCOPIC - ACTIVE TEST REFERENCE

Tester Display	Test Part	Control Range
Tilt Operation	Tilt operation	Up/Down
Telesco Operation	Telescopic operation	Long/Short