Rear Seat Outer Belt Assembly: Installation: Installation

INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY
1. Install the rear seat 3 point type belt assembly with the 2 bolts.
  
  Fig 1: Identifying Rear Seat 3 Point Type Belt Assembly And Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Bolt <A>
  
  Torque: 4.9 N*m (50 kgf*cm, 43 in.*lbf)
  
  Bolt <B>
  
  Torque: 41 N*m (420 kgf*cm, 30 ft.*lbf)
2. Connect the shoulder anchor of the rear seat 3 point type belt assembly with the bolt.
  
  Fig 2: Identifying Shoulder Anchor Of Rear Seat 3 Point Type Belt Assembly And Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 41 N*m (420 kgf*cm, 30 ft.*lbf)
3. Check if the ELR locks.
  NOTE:
  The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL ROOF SIDE INNER GARNISH LH . Refer to INSTALLATION - Step 20
INSTALL QUARTER PILLAR GARNISH LH . Refer to INSTALLATION - Step 21
INSTALL SIDE DECK TRIM PANEL ASSEMBLY LH . Refer to INSTALLATION - Step 22
INSTALL REAR COMBINATION LIGHT SERVICE COVER LH . Refer to INSTALLATION - Step 23
INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side) . Refer to INSTALLATION - Step 24
INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side) . Refer to INSTALLATION - Step 25
INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
1. Connect the floor anchor end of the rear seat 3 point type belt assembly LH and install the bolt.
  
  Fig 3: Identifying Floor Anchor End Of Rear Seat 3 Point Type Belt Assembly LH And Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 41 N*m (420 kgf*cm, 30 ft.*lbf)
  
  NOTE:
  Do not allow the anchor part of the rear seat 3 point type belt assembly LH to overlap the protruding part of the floor panel.
INSTALL REAR SEAT SIDE GARNISH LH . Refer to INSTALLATION - Step 27
INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY (for LH Side) . Refer to INSTALLATION - Step 28
INSTALL ROOF SIDE INNER GARNISH RH . Refer to INSTALLATION - Step 29
INSTALL QUARTER PILLAR GARNISH RH . Refer to INSTALLATION - Step 30
INSTALL SIDE DECK TRIM PANEL ASSEMBLY RH . Refer to INSTALLATION - Step 31
INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side) . Refer to INSTALLATION - Step 32
INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side) . Refer to INSTALLATION - Step 33
INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
1. Connect the floor anchor end of the rear seat 3 point type belt assembly RH and install the bolt.
  
  Fig 4: Identifying Floor Anchor End Of Rear Seat 3 Point Type Belt Assembly RH Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 41 N*m (420 kgf*cm, 30 ft.*lbf)
  
  NOTE:
  Do not allow the anchor part of the rear seat 3 point type belt assembly RH to overlap the protruding part of the floor panel.
INSTALL REAR SEAT SIDE GARNISH RH . Refer to INSTALLATION - Step 35
INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY (for RH Side) . Refer to INSTALLATION - Step 36
INSTALL REAR DECK TRIM COVER . Refer to INSTALLATION - Step 37
INSTALL LUGGAGE COMPARTMENT TRAY . Refer to INSTALLATION - Step 38
INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR See step 1
INSTALL DECK FLOOR BOX RH . Refer to INSTALLATION - Step 40
INSTALL DECK FLOOR BOX LH . Refer to INSTALLATION - Step 41
INSTALL JACK ASSEMBLY . Refer to INSTALLATION - Step 42
INSTALL JACK CARRIER ASSEMBLY
INSTALL NO. 2 DECK BOARD . Refer to INSTALLATION - Step 44
INSTALL DECK BOARD ASSEMBLY . Refer to INSTALLATION - Step 45
INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH . Refer to INSTALLATION - Step 62
INSTALL REAR DOOR SCUFF PLATE LH . Refer to INSTALLATION - Step 63
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH . Refer to INSTALLATION - Step 68
INSTALL REAR DOOR SCUFF PLATE RH . Refer to INSTALLATION - Step 69
INSTALL REAR SEAT CENTER OUTER BELT ASSEMBLY
1. Install the rear seat center outer belt assembly with the bolt.
  
  Fig 5: Identifying Rear Seat Center Outer Belt Assembly Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
INSTALL REAR SEATBACK BOARD . Refer to REASSEMBLY - Step 10
INSTALL REAR SEAT SHOULDER BELT HOLE COVER
1. Engage the 2 claws and 2 guides to install the rear seat shoulder belt hole cover.
  
  Fig 6: Identifying Rear Seat Shoulder Belt Hole Cover Claws And Guides
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL SEAT BELT ANCHOR COVER CAP
1. Engage the 2 claws to install the seat belt anchor cover cap.
  
  Fig 7: Identifying Seat Belt Anchor Cover Cap Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR SEATBACK ASSEMBLY RH . Refer to INSTALLATION - Step 1
INSTALL REAR SEATBACK INNER HINGE COVER (for RH Side) . Refer to INSTALLATION - Step 2
INSTALL REAR SEATBACK OUTER HINGE COVER (for RH Side) . Refer to INSTALLATION - Step 3
CONNECT REAR SEAT CENTER OUTER BELT ASSEMBLY
1. Install the rear seat center outer belt assembly and the rear seat inner belt assembly with the bolt.
  
  Fig 8: Identifying Rear Seat Center Outer Belt Assembly Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  Torque: 41 N*m (420 kgf*cm, 30 ft.*lbf)
  
  NOTE:
  Do not allow the anchor part of the rear seat center outer belt assembly and rear seat inner belt assembly to overlap the protruding part of the floor panel.
INSTALL REAR SEAT CENTER HEADREST ASSEMBLY
INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)
INSTALL REAR SEATBACK ASSEMBLY LH . Refer to INSTALLATION - Step 7
INSTALL REAR SEATBACK INNER HINGE COVER (for LH Side) . Refer to INSTALLATION - Step 8
INSTALL REAR SEATBACK OUTER HINGE COVER (for LH Side) . Refer to INSTALLATION - Step 9
INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)
INSTALL REAR SEAT CUSHION ASSEMBLY . Refer to INSTALLATION - Step 11