Special Tools

Special tools and workshop equipment required 

• Engine Support Bridge 10-222 A
• Engine Support Feet 10-222 A/8
• Hose Clamps up to 25 mm Dia. 3094
• Transmission Support 3282
• Sleeve 3160
• Bracket 30-211A
• Thrust Piece T10042
• Thrust Piece T40008
• Hot Air Blower V.A.G 1416
• Extractor Lever VW 681
• Thrust Piece T10143
• Press Tool for Shaft Seal T10180
• Driving Sleeve VW 244B
• Thrust Plate VW 401
• Thrust Plate VW 402
• Punch VW 407
• Tube 37 mm Dia. VW 416 B
• Guide Piece VW 436 A
• Guide Pin VW 439
• Holding Fixture VW 801
• Guide Piece 10-15
• Thrust Pad 3124
• Punch VW 411
• Tube Trans. Drive Shaft VW 426
• Thrust Pad 16.5/28 mm Dia. VW 431
• Triple Square Socket Driver 3357
  Fig 1: 3357 Triple Square Socket Driver

  Courtesy of VOLKSWAGEN UNITED STATES, INC.
• Connecting Pin T10027 A
  Fig 2: Identifying Connecting Pin T10027 A

  Courtesy of VOLKSWAGEN UNITED STATES, INC.
• Hose Clamp Pliers V.A.G 1275
  Fig 3: Identifying Hose Clamp Pliers V.A.G 1275

  Courtesy of VOLKSWAGEN UNITED STATES, INC.
• Special Hook 3370
  Fig 4: Front End Hook VAS 3370

  Courtesy of VOLKSWAGEN UNITED STATES, INC.
• Sleeve VW 423
  Fig 5: Identifying Sleeve VW 423

  Courtesy of VOLKSWAGEN UNITED STATES, INC.
• Extractor Lever T20143/1
  Fig 6: Extractor Hook T20143

  Courtesy of VOLKSWAGEN UNITED STATES, INC.
• Thrust Block T10083
  Fig 7: Identifying Pressing Support T10083

  Courtesy of VOLKSWAGEN UNITED STATES, INC.
• Drift T10169 or T10362
  Fig 8: Identifying Drift T10362

  Courtesy of VOLKSWAGEN UNITED STATES, INC.
• Socket and Extended Bit T10107 or T10107 A
  Fig 9: Identifying Multi-Point Socket T10107 A

  Courtesy of VOLKSWAGEN UNITED STATES, INC.

Special tools and workshop equipment required 

• -1- Kukko Extractor 14.5-18.5 mm 21/2
• -1- Kukko Extractor 23.5-30 mm 21/4
• -1- Kukko Puller 12-14.5 mm 21/1
• -1- Kukko Extractor 18.5-23.5 mm 21/3
• -3- Kukko Separating Tool 5-60 mm 17/0
• -4- Kukko Support 22/2
• -4- Kukko Support 22/1
  Fig 10: Identifying Kukko Tools

  Courtesy of VOLKSWAGEN UNITED STATES, INC.

Special tools and workshop equipment required 

• Transmission Support Elements (Pin 3289/29) (determine when mounting the adjustment plate on the transmission support)
• Adjustment Plate 3282/33
• Transmission Support Jig 3336
• Torque Wrench (5-50 Nm) V.A.G 1331
• Torque Wrench (40-200 Nm) V.A.G 1332
• Engine/Transmission Jack V.A.G 1383 A

Special tools and workshop equipment required 

• Holding Plate VW 309
• Holding Fixture VW 313
• Transmission Support VW 353
• Thrust Tube VW 455
• Slide Hammer-Complete Set VW 771
• Sleeve 30-21