Section 28 (Brake System Components - Removal And Installation)
WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2007 Volvo V70, 2006 Volvo V70, 2005 Volvo V70, 2004 Volvo V70, and 2003 Volvo V70. However, it is still accessible from the selected car via links, so may be relevant.
- Front Brake
- Brake calipers, front, replacing
- Brake disc front, replacing
- Brake pads front, replacing
- Brake pipe hydraulic unit / junction / front wheel, replacing
- Front wheel hub, replacing
- Replacing front wheel hub, Steel & Aluminium
- Rear Brake
- Brake Control
- Active yaw control sensor, replacing
- Brake Control Module (BCM), replacing
- Connecting the breakout box
- Contact reel / steering wheel angle sensor, replacing
- Notes
- Removal
- Preparations
- Removing steering wheel module
- Removing the center screw from the steering wheel
- Locking the contact reel
- Marking the position of the steering wheel
- Removing the steering wheel
- Removing steering column covers
- Removing the contact reel and steering wheel angle sensor
- Resetting the contact reel and steering wheel angle sensor (Only to be carried out when the default position has been changed)
- Checking the locking screw
- Installation
- Control module (ABS), replacing
- Hydraulic unit, replacing
- Master cylinder, replacing (left-hand drive)
- Notes
- Preparatory work
- Removal
- Installation
- Finishing
- Brake pipe master cylinder / ABS unit, replacing
- Notes
- Replacing the brake pipe for the left-hand front wheel / ABS unit
- Preparatory work
- Removing the air cleaner (ACL) housing
- Removing the integrated relay / fusebox
- Removing the left-hand brake pipe
- Installing the brake pipe for the left-hand front wheel / ABS unit
- Installing the integrated relay / fusebox
- Installing the air cleaner (ACL) housing
- Finishing
- Testing the pressure of the brake system
- Replacing the brake pipe for the right-hand front wheel / ABS unit
- Notes
- Preparatory work
- Removing the air cleaner (ACL) housing
- Removing the integrated relay / fusebox
- Removing the brake pipe for the right-hand front wheel / ABS unit
- Installing the brake pipe for the right-hand front wheel / ABS unit
- Installing the integrated relay / fusebox
- Installing the air cleaner (ACL) housing
- Finishing
- Testing the pressure of the brake system
- Master cylinder, replacing (right-hand drive)
- Pedal sensor power brake booster, replacing
- Power brake booster, replacing
- Notes
- Removal
- Preparations for removing the power brake booster
- Remove the master cylinder
- Remove Soundproofing Panel
- Remove the nuts for the power brake booster at the pedal box
- Remove the splash guard under the engine
- Remove the mounting screw for the cable conduit
- Remove the three cross members under the car
- Remove the locking screw and lock from the steering gear
- Cars with passenger compartment heaters
- Preparations for removing sub-frame screws
- Lower the sub-frame
- Lower the car. Remove the power brake booster
- Installation
- Transfer the terminals and seals to the new power brake booster
- Install the power brake booster with the terminals for the check valve
- Tighten the power brake booster
- Install the master cylinder
- Install the connections on the master cylinder
- Lift the sub-frame
- Install the steering components
- Secure the sub-frame
- Install the cross members
- Pressure sensor, master cylinder, replacing
- Replacing ABS / DSTC (dynamic stability and traction control) control module
- Replacing the control module
- Replacing the control module for ABS and dynamic stability and traction control (DSTC)
- Replacing the power brake booster (DSTC)
- Notes
- Removal
- Preparations for removing the power brake booster
- Remove the master cylinder
- Remove the nuts for the power brake booster at the pedal box
- Remove the splash guard under the engine
- Remove the mounting screw for the cable conduit
- Remove the three cross members under the car
- Remove the locking screw and lock from the steering gear
- Cars with passenger compartment heaters
- Preparations for removing sub-frame screws
- Lower the sub-frame
- Lower the car. Remove the power brake booster
- Installation
- Transfer the terminals and seals to the new power brake booster
- Install the power brake booster with the terminals for the check valve
- Tighten the power brake booster
- Install the master cylinder
- Install the connections on the master cylinder
- Lift the sub-frame
- Install the steering components
- Secure the sub-frame
- Install the cross members
- Replacing the yaw rate sensor (1) and the lateral acceleration sensor in the center console (DSTC)
- Replacing the yaw rate sensor (2) (DSTC)
- Steering wheel module (SWM), replacing
- Stop lamp switch, replacing
- Vacuum system, checking
- Wheel sensor, front, replacing
- Wheel sensors, rear, replacing
- Brake System
- Parking Brake