Section 6 (Engine Control System - 3.9L - Introduction (2 Of 2))
WARNING: This page is about a different variant/trim than selected.
- Specifications
- Temperature vs Resistance
- Temperature vs Resistance - Engine Coolant Temperature (ECT) Sensor
- Temperature vs Resistance - Intake Air Temperature (IAT) Sensor
- Altitude vs Barometric Pressure
- Ignition System Specifications
- Fastener Tightening Specifications
- Diagnostic Trouble Code (DTC) Type Definitions
- Diagnostic Trouble Code (DTC) Type(s)
- Schematic and Routing Diagrams
- Component Locator
- Engine Controls Component Views
- Engine Control Module (ECM) Connectors
- Engine Controls Connectors
- Accelerator Pedal Position (APP) Sensor
- Camshaft Position (CMP) Actuator Solenoid
- Camshaft Position (CMP) Sensor
- Crankshaft Position (CKP) Sensor
- Engine Coolant Temperature (ECT) Sensor
- Evaporative Emission (EVAP) Canister Purge Solenoid Valve
- Evaporative Emission (EVAP) Canister Vent Solenoid
- Fuel Injector 1
- Fuel Injector 2
- Fuel Injector 3
- Fuel Injector 4
- Fuel Injector 5
- Fuel Injector 6
- Fuel Pump And Sender Assembly
- Fuel Tank Pressure (FTP) Sensor
- Heated Oxygen Sensor (HO2S) 1
- Heated Oxygen Sensor (HO2S) 2
- Ignition Control Module (ICM)
- Intake Manifold Tuning (IMT) Valve Solenoid
- Knock Sensor (KS) Bank 1
- Knock Sensor (KS) Bank 2
- Manifold Absolute Pressure (MAP) Sensor
- Mass Air Flow (MAF)/Intake Air Temperature (IAT) Sensor
- Throttle Actuator Control (TAC) Module
- Diagnostic Information and Procedures
- Repair Instructions
- Engine Control Module (ECM) Replacement
- CKP System Variation Learn Procedure
- Engine Coolant Temperature (ECT) Sensor Replacement
- Mass Air Flow (MAF)/Intake Air Temperature (IAT) Sensor Replacement
- Manifold Absolute Pressure (MAP) Sensor Replacement
- Heated Oxygen Sensor Replacement - Position 1
- Heated Oxygen Sensor Replacement - Position 2
- Accelerator Pedal with Position Sensor Replacement
- Throttle Body Assembly Replacement
- Throttle Body Service
- Fuel Pressure Relief Procedure
- Fuel Pressure Gage Installation and Removal
- Quick Connect Fitting(s) Service (Metal Collar)
- Quick Connect Fitting(s) Service (Plastic Collar)
- Fuel Tank Draining Procedure
- Fuel Tank Replacement
- Fuel Tank Pressure Sensor Replacement
- Filler Tube Replacement
- Fuel Tank Module Replacement
- Fuel Level Sensor Replacement
- Fuel Hose/Pipes Replacement - Chassis
- Fuel System Cleaning
- Fuel Rail Assembly Replacement
- Fuel Injector Replacement
- Evaporative Emission (EVAP) Canister Purge Solenoid Valve Replacement
- Evaporative Emission (EVAP) Canister Vent Solenoid Valve Replacement
- Evaporative Emission (EVAP) Hoses/Pipes Replacement - Engine/Chassis
- Evaporative Emission (EVAP) Canister Replacement
- Evaporative Emission (EVAP) System Cleaning
- Ignition Coil(s) Replacement
- Spark Plug Wire Inspection
- Spark Plug Wire Replacement
- Spark Plug Inspection
- Spark Plug Replacement
- Camshaft Position (CMP) Sensor Replacement
- Crankshaft Position (CKP) Sensor Replacement
- Knock Sensor (KS) Replacement - Bank 1
- Knock Sensor (KS) Replacement - Bank 2
- Intake Manifold Tuning Valve Replacement
- Air Cleaner Element Replacement
- Air Cleaner Assembly Replacement
- Air Cleaner Outlet Duct Replacement
- Description and Operation
- Engine Control Module (ECM) Description
- Intake Manifold Tuning Valve System Description
- Throttle Actuator Control (TAC) System Description
- Camshaft Actuator System Description
- Fuel System Description
- Fuel System Overview
- Fuel Tank
- Fuel Fill Pipe
- Fuel Filler Cap
- Fuel Sender Assembly
- Fuel Level Sensor
- Fuel Pump
- Fuel Strainer
- Fuel Feed Pipe
- Nylon Fuel Pipe
- Quick-Connect Fittings
- Fuel Pipe O-Rings
- Fuel Rail Assembly
- Fuel Injectors
- Fuel Pressure Regulator
- Fuel Metering Modes of Operation
- Starting Mode
- Clear Flood Mode
- Run Mode
- Acceleration Mode
- Deceleration Mode
- Battery Voltage Correction Mode
- Fuel Cutoff Mode
- Short Term Fuel Trim
- Long Term Fuel Trim
- Evaporative Emission (EVAP) Control System Description
- Electronic Ignition (EI) System Description
- Special Tools and Equipment