Transaxle Specifications
TRANSAXLE SPECIFICATIONS
| Application | In. (mm) | ||
|---|---|---|---|
| Differential Assembly Side Gear-To-Differential Case Specified Clearance | .004-.008 (0.10-0.20) | ||
| Differential End Play | 0-.006 (0-.15) | ||
| Differential Side Bearing Preload (RL4F03V) | .002-.004 (.04-.10) | ||
| Final Drive End Play (RL4F03A) | 0-.006 (0-.15) | ||
| Forward & Overrun Clutches Dish Plate Thickness | |||
| Forward Clutch | .098 (2.50) | ||
| Overrun Clutch | .085 (2.15) | ||
| Drive Plate Thickness (Forward Clutch) | |||
| Standard Clearance | .071 (1.80) | ||
| Allowable Limit | .063 (1.60) | ||
| Drive Plate Thickness (Overrun Clutch) | |||
| Standard Clearance | .063 (1.60) | ||
| Allowable Limit | .055 (1.40) | ||
| Retaining Plate-To-Snap Ring | |||
| Specified Clearance | |||
| Forward Clutch | .018-.033 (.45-.85) | ||
| Overrun Clutch | .039-.055 (1.00-1.40) | ||
| Allowable Limit | |||
| Forward Clutch | .073 (1.85) | ||
| Overrun Clutch | .079 (2.00) | ||
| High Clutch | |||
| Dish Plate Thickness | .106 (2.70) | ||
| Drive Plate Thickness | .079 (2.00) | ||
| Allowable Limit | .071 (1.80) | ||
| Retaining Plate-To-Snap Ring | |||
| Specified Clearance | .055-.071 (1.40-1.80) | ||
| Allowable Limit | .094 (2.40) | ||
| Input Shaft Seal Ring-To-Ring Groove | |||
| Specified Clearance | .003-.009 (.08-.23) | ||
| Allowable Limit | .009 (.23) | ||
| Low-Reverse Brake | |||
| Drive Plate Thickness | |||
| Standard | .079 (2.00) | ||
| Allowable Limit | .071 (1.80) | ||
| Specified Clearance | |||
| Standard | .055-.071 (1.40-1.80) | ||
| Allowable Limit | .110 (2.80) | ||
| Oil Pump Seal Ring-To-Ring Groove | |||
| Specified Clearance | .004-.010 (.10-.25) | ||
| Allowable Limit | .010 (.25) | ||
| Oil Pump Side Clearance | .0008-.0016 (.020-.040) | ||
| Output Shaft Bearing Preload (RL4F03A) | .001-.003 (.03-.08) | ||
| Output Shaft End Play (RL4F03V) | 0-.020 (0-.50) | ||
| Output Shaft Seal Ring-To-Ring Groove | |||
| Specified Clearance | .004-.010 (.10-.25) | ||
| Allowable Limit | .010 (.25) | ||
| Pinion Washer-To-Planetary Gear | |||
| Specified Clearance | .006-.028 (.15-.70) | ||
| Allowable Limit | .031 (.80) | ||
| Reverse Clutch | |||
| Dish Plate Thickness | .110 (2.80) | ||
| Drive Plate Thickness | .079 (2.00) | ||
| Allowable Limit | .071 (1.80) | ||
| Retaining Plate-To-Snap Ring | |||
| Specified Clearance | .020-.031 (.50-.80) | ||
| Allowable Limit | .047 (1.20) | ||
| Reduction Gear Bearing Preload | .002 (.05) | ||
| Reverse Clutch End Play | .026-.039 (.65-1.00) | ||
| Total End Play | .010-.022 (.25-.55) | ||