General Orphan Data (2 Of 2)

• Switch block - manual transmission
• Removing and installing (replacing) function carrier on instrument panel trim
• Switch block - automatic transmission
• Remove left and right side center console trim panel
• Removing the selector lever
• Installing the selector lever
• Install left and right side center console trim panel
• Install rear cup holder
• Installing clutch cover (7DCT300)
• Remove front wheel
• Mount the front wheel
• Drain oil from the double-clutch transmission (DCT) (7DCT300)
• Fill oil in the double-clutch transmission (DCT) (7DCT300)
• Tie rods
• Wishbone
• Removing underbody planking on left and right side
• Disconnecting the wiring harness of the electromechanical steering gear
• Releasing the heat pump heat exchanger from the front axle support
• Releasing the electrical heating from the front axle support
• Releasing the engine pendulum support
• Releasing the wishbone and the tie rod from the swivel bearing
• Preparing the special tool
• Fastening the wishbone and the tie rods on the swivel bearing
• Secure mounted parts on the front axle support
• Fastening the engine pendulum support
• Securing the electrical heating on the front axle support
• Connecting the wiring harness of the electromechanical steering gear
• Remove underbody protection at side right and left
• Electric components
• Steering
• Anti-roll bar
• Front bumper
• Steering column
• Perform chassis alignment check
• Checking the airbag for function
• Spring strut
• Front Brake
• Wheel Bearings and Steering Knuckle
• Output shaft
• Releasing the output shaft, right, from the wheel bearing
• Fastening the right output shaft on the wheel bearing
• Certification of: _____
• Measuring vehicle ride height
• Chassis/wheel alignment - normal position, MINI, F55
• Wishbone/trailing arm and struts
• Teaching in end stop software for electric steering gear (EPS)
• Replacement: Commissioning (initialization) of the electromechanical steering
• Steering wheel
• Shock Absorbers
• Rear axle carrier
• Brake lines
• Removing the rear left and right wheels
• Removing the underbody shield for rear axle on left and right
• Release the potential equalization line
• Disconnect the high-voltage plug connection
• Prepare the mobile table lift
• Removing the cover on the left and right trailing arm
• Release cable from the rear axle support
• Detach ride height sensor from the top wishbone
• Removing left and right coil spring
• Mounting the trailing arm on the left and right of the shock absorber
• Releasing the brake hose on the left and right of the trailing arm
• Install brake pedal tensioner
• Releasing the brake hose on the left and right of the rear axle support
• Securing the brake hose on the left and right of the rear axle support
• Remove the brake pedal tensioner
• Securing the brake hose on the left and right of the trailing arm
• Releasing the trailing arm on the left and right of the shock absorber
• Installing left and right coil spring
• Fasten the ride height sensor on the top wishbone
• Securing the cable to the rear axle support
• Installing the cover on the left and right trailing arm
• Checking undercoating for damage
• Connect high-voltage connector
• Secure the potential equalization line
• Installing the underbody shield for rear axle on left and right
• Vent braking system
• Install the rear left and right wheels
• Tighten the screw connection on the left and right on the trailing arm
• Removing the wishbone at the bottom on the left and right
• Removing the wishbone at the top on the left and right
• Installing the wishbone at the top on the left and right
• Installing the wishbone on the bottom left and right
• Tightening the screw connections on the rear axle support on the left and right
• Tightening the screw connections on the lower wishbone on the left and right
• Detach the anti-roll bar link from trailing arm on left and right
• Secure the anti-roll bar link on the left and right to the trailing arm
• Rear brakes
• Wheel Bearings
• Slip control system (DSC)
• Tighten the screw connection on the rear axle support
• Removing the cover on the trailing arm
• Tighten the screw connections on the bottom wishbone
• Main group 34
• Brake test and bleeding
• 3.0 Approved brake fluids
• Remove the front left and right wheels
• Partly loosening the wheel arch cover in front
• Removing the front brake pad wear sensor (fixed caliper brake)
• Installing front brake pad wear sensor (fixed caliper brake)
• Installing the front wheel arch cover
• Installing the front left and right wheels
• Commissioning or bedding in (brake) of new brake pads and discs (high brake)
• Removing and installing/replacing the windshield panel cover, left
• Tandem brake master cylinder
• Removing and installing (replacing) lower left instrument panel trim
• Brake booster
• Removing and installing/replacing EMF actuator
• Removing and installing/replacing the windshield panel cover, right
• Pedal bracket
• Foot controls
• Wheels
• Resetting the Tire Pressure Monitor
• Disc wheels (rims)
• Notes on mounting tires
• Prepare the tires for disassembly
• Prepare the tires for installation
• Fill/inflate tire
• Optimizing the tire bead fit
• Stationary wheel balance
• Resetting the RDC
• Observe the notes on mounting RSCs
• Preparing runflat tires for disassembly
• Cosmetic repairs on rims
• Vehicle identification number, general
• Note on the Dealer Equipment Catalog
• Filler S1
• Safety instructions and general information
• Information/warning labels
• Removing and installing/replacing left or right actuator (active pedestrian protection)
• Reinforcement plate
• Products for the repair of aluminum
• Smart Repair for pressing out dents
• Products for the repair of steel
• Tail cowling
• Rear seats
• Removing and installing/replacing trim on front left or right wheel arch
• Side panels
• Detaching and attaching/replacing trim panel for left or right door sill
• Door, front
• Front Door Locks
• Rear door
• Door locks, rear
• Hood
• Removing and installing/replacing rear spoiler
• Removing and installing/replacing the cover for the rear window frame at top
• Removing and installing or replacing trim for rear lid
• Tailgate
• Removing and installing or replacing headlining (with sliding/tilting sunroof)
• Removing and installing/replacing striker for tailgate lock
• Adjusting rear lid lock
• Adjusting/replacing bump stops
• Cord for separating adhesions
• Removing the trim on the left and right air duct
• Installing the trim on the left and right air duct
• Remove the left and right fog light brackets
• Removing the ornamental grille on the front left and right side
• Installing the ornamental grille on the front left and right side
• Installing the fog light bracket on the left and right
• Remove fog lamp holders
• Installing fog light support
• Partially releasing the right wheel arch trim panel
• Remove washer fluid reservoir
• Remove impact absorber
• Install the impact absorber
• Installing washer fluid reservoir
• Removing the left and right front fog light
• Installing the mount for the left and right front fog lights
• Installing the mount for the front fog light on the left and right
• Installing the left and right front fog light
• Removing the left and right tail lights
• Remove rear bumper panel
• Installing the rear bumper cover
• Install the left and right tail lights
• Removing and installing rear bumper panel
• Remove the left and right front fog light
• Install the left and right front fog light
• Removing the decorative strip on the driver's side
• Removing the decorative strip on the passenger's side
• Removing the ring trim
• Installing the ring trim
• Installing the right decorative strip
• Installing the left decorative strip
• Remove side center console trim panel
• Install trim panel center console laterally
• Air conditioning, refrigerant amounts, BMW, F20, F21, F22, F23, F30, F31, F32, F33, F34, F35, F36, F54, F55, F56, F57, F80, F82, F83, F87
• Draw off and dispose of contaminated refrigerant R1234yf
• Adapter
• Partially removing the vacuum pump
• Removing the air conditioning condenser partially
• Visual inspection of the drained refrigerant oil from the air conditioning compressor
• Carry out a visual inspection of the drained refrigerant oil in the A/C service station oil reservoir
• Releasing the rear intake pipe
• Removing the non-return valve
• Installing the non-return valve
• Mounting the intake pipe at the rear
• Partially installing the vacuum pump
• Reading out the fault memory
• Store tools
• Refrigerant Lines and Expansion Valve
• Air conditioning compressor
• Partially installing the air conditioning condenser
• Running in the new air conditioning compressor
• Partially remove the electric A/C compressor (EKK)
• Partially installing the electric A/C compressor (EKK)
• Remove left and right wiper blade
• Install the left and right wiper blade
• Radio
• Removing and installing/replacing left trunk wheel arch trim
• Loudspeakers
• Roof antenna
• Airbag control unit
• Control of airbag deployment
• Removing and installing/replacing rear left or right side trim panel
• Removing and installing/replacing the door lock in the left or right rear door
• Removing and installing/replacing tailgate lock
• Removing and installing/replacing complete rear left or right power electric windows
• Power windows, rear
• Removing and installing/replacing trim panel for storage shelf
• Remove and install/replace top dashboard storage compartment
• Overview of clips and release tools for head airbag fastening
• Removing and installing/replacing center armrest
• When replacing the gasoline particulate filter: Register the gasoline particulate filter
• 12.0 Transmission oil for automatic transmissions GACVT16Z (CVT)/GA6F21WA (AISIN)/GA8F22AW (AISIN)
• Transmission Case, Oil Sump
• 13.0 Engine oil consumption measurement
• 14.0 Record for motor oil consumption measurement
• Checking/topping up oil level in automatic transmission (AISIN GA8G45)
• Removing right headlight
• Remove front right wheel
• Installing the front right wheel
• Install right headlight
• Partially detaching wheel arch trim panel on left and right
• If installed: Removing the right brake ventilation duct
• If installed: Install right brake ventilation duct
• Mounting wheel arch trim panel on left and right
• Observing the hardening time of the screw locking agent on the screw plug
• Disassembling the cylinder head from the special tool
• Disconnecting the transmission oil lines
• Fastening transmission oil lines
• Move the engine to the installation position
• Take engine out of installation orientation
• Block the crankshaft in he TDC firing position of cylinder 1
• Removing and installing/replacing front left or right wheel arch cover
• Removing and installing/replacing strip on rear left or right side window
• Mirrors, Decorative strips, Ashtrays, Consoles
• Remove mirror glass
• Installing the mirror glass
• Removing and installing/replacing the outside door handle on the left or right front door
• Removing and installing/replacing sound insulation in left or right front door
• Removing and installing left or right front door trim panel
• Vacuum lifting tool, Hazet
• "Spider" dismantling system for bonded glazing
• Wire pull handle with suction element
• Pinchweld scraper set
• Remove the windshield
• Dashboard protection for vehicle window removal
• Wire starter for window final assembly
• Removing and installing/replacing interior rearview mirror (overview)
• Front power electric windows
• Removing and installing/replacing the window channel strip on the outside of the front door
• Side trim panel with armrest
• Safety belt
• Trim panel, instrument panel
• Removing and installing/replacing airbag control unit
• Removing and installing/replacing top cover on tail panel
• Replacing cover on trim panel for cover on side member, left or right
• Front seats
• Airbag modules
• Removing the front strap fitting
• Installing the front strap fitting
• Removing seat cover with cushion
• Removing the seat cover with cushion
• Removing the backrest cover with the cushion
• Installing the backrest covering with the cushion
• Components of the slide/tilt sunroof mechanism
• Remove glass slide/tilt sunroof panel at rear
• Checking the setting of the panorama glass roof
• Adjusting rear glass slide/tilt sunroof panel
• Install rear glass slide/tilt sunroof panel
• Remove front glass slide/tilt sunroof panel
• Installing the front glass slide/tilt sunroof panel
• Adjusting front glass slide/tilt sunroof panel
• Initialize panorama glass roof
• Crimping tool for repairing the coaxial line RTK031
• Safety instructions for handling electric and hybrid vehicles
• Battery with terminal
• Removing the battery cover on the side
• Installing the battery cover at the side
• Recoding of spare parts (housings and contacts) from "Repair set 4 for vehicle electrical system" All
• New universal crimping die All
• New crimping pliers and interchangeable dies All
• New "MultiStrip 10" insulation strippers
• New release tools for electrical contacts All
• New release tools and insertion aids for electrical contacts All
• New release tools for electrical contacts MINI
• New release tool for electrical contacts MINI
• Wiring harness repair kit 4.0 (61 13 4 470 939) and associated special tools
• Removing and installing/replacing right glove compartment with housing
• F60 Power distribution box, current terminals
• Register battery change
• Perform EoS test
• Preparing the position plan
• Adjust charging voltage
• Removing and installing/replacing side panel on dashboard on left or right
• Removing and installing/replacing right trunk wheel arch panel
• Fanfare horn
• Enclosure 1 to SWS 01 08 09 (531)
• New main number for the antistatic mat
• Replacing the gel pad for rain light solar mist sensor
• Car Sharing Module
• Disconnecting the high-voltage plug connections
• Disconnect the plug connection
• Disconnecting the coolant lines
• Disconnect plug connections
• Disconnecting the high-voltage plug connection from the electrical machine electronics (EME)
• Closing the high-voltage plug connection at the EME
• Closing the plug connections
• Connecting the coolant lines
• Close plug connection
• Closing the high-voltage plug connections
• Windshield wiper system, front
• Rear wiper
• Instrument panel
• Removing and installing dashboard trim
• Head-Up Display (F 5x)
• Headlight
• Fog lights, marker light
• Removing and installing/replacing cover on left or right tail light
• Rear light
• Removing center rear undershield
• Removing the side rear undershield
• Installing the side rear undershield
• Installing center rear undershield
• Auxiliary stop lamp
• Removing and installing/replacing the trunk lid handle
• Remove and install left or right rear door trim panel
• Interior lights, MINI, F5x/F60
• Fog light, additional high-beam headlight, MINI, F5x
• Rear fog lights, MINI, F5x
• Turn signals, MINI, F5x/F60
• Removing and installing (replacing) side center console trim panel
• Removing the Electrical Digital Motor Electronics (EDME) partially
• Installing the Electrical Digital Motor Electronics (EDME) partially
• Repair notes on replacing the cylinder head